Read the L2 doorbell size from the firmware and only map the portion
of the doorbell BAR for L2 use. This will leave the remaining doorbell
BAR available for the RoCE driver to use. The RoCE driver can map
the remaining portion as write-combining to support the push feature.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver provides completion ring or NQ doorbell offset for each
MSIX entry requested by the RDMA driver. The NQ offset on 57500
chips is different than legacy chips. Set it correctly based on
chip type for correctness. The RDMA driver is ignoring this field
for the 57500 chips so it is not causing any problem.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the 57500 chip doorbell offsets instead of using the magic
values in the C file.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel log messages for failed AP reset commands should be suppressed.
These are expected to fail on devices that do not have an AP. Add
missing driver reload message after AP reset and log it in a common
way without duplication.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool ABI specifies that the reset operation should only clear
the flags that were actually reset. Setting the flags to zero after
a chip reset violates this because it does not include resetting the
application processor complex. Similarly, components that are not yet
defined are also not necessarily being reset.
The fact that chip reset does not cover the AP also means that it is
inappropriate to treat these two components exclusively of one another.
The ABI provides a mechanism to report a failure to reset independent
components via the returned bitmask, so it is also wrong to fail hard
if one of a set of independent resets is not possible.
It is incorrect to rely on the passed by reference flags in bnxt_reset(),
which are being updated as components are reset. The initially requested
value should be used instead so that hard errors do not propagate if any
earlier components could have been reset successfully.
Note, AP and chip resets are global in nature. Dedicated resets are
thus not currently supported.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The case statement in bnxt_firmware_reset() dangerously mixes types.
This patch separates the application processor and whole chip resets
from the rest such that the selection is performed on a pure type.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract bnxt_hwrm_firmware_reset() for performing firmware reset
operations. This new helper function will be used in a subsequent
patch to separate unrelated reset types out of bnxt_firmware_reset().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware does not expect the CRC to be included in the length
passed from the driver. The firmware always configures the chip
to strip out the CRC.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current formulas to calculate the TQM slow path and fast path ring
context memory sizes are not quite correct. TQM slow path entry is
array index 0 of ctx->tqm_mem[]. The other array entries are for fast
path. Fix these sizes according to latest firmware spec. for 57500 and
newer chips.
Fixes: 3be8136ce1 ("bnxt_en: Initialize context memory to the value specified by firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware spec. will specify the number of TQM rings to allocate
context memory for. Use the firmware specified value and fall back
to the old value derived from bp->max_q if it is not available.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes include additional statistics, ECN support, context memory
interface change for better TQM context memory sizing, firmware
health status definitions, etc.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic in bnxt_fix_features() will inadvertently turn on both
CTAG and STAG VLAN offload if the user tries to disable both. Fix it
by checking that the user is trying to enable CTAG or STAG before
enabling both. The logic is supposed to enable or disable both CTAG and
STAG together.
Fixes: 5a9f6b238e ("bnxt_en: Enable and disable RX CTAG and RX STAG VLAN acceleration together.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_alloc_ctx_pg_tbls() should return error when the memory size of the
context memory to set up is zero. By returning success (0), the caller
may proceed normally and may crash later when it tries to set up the
memory.
Fixes: 08fe9d1816 ("bnxt_en: Add Level 2 context memory paging support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the slot reset sequence by disabling the device to prevent bad
DMAs if slot reset fails. Return the proper result instead of always
PCI_ERS_RESULT_RECOVERED to the caller.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom adapters support only maximum of 512 CQs per PF. If user sets
MSIx vectors more than supported CQs, firmware is setting incorrect value
for msix_vec_per_pf_max parameter. Fix it by reducing the BNXT_MSIX_VEC_MAX
value to 512, even though the maximum # of MSIx vectors supported by adapter
are 1280.
Fixes: f399e84978 ("bnxt_en: Use msix_vec_per_pf_max and msix_vec_per_pf_min devlink params.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic that sets the enable/disable flag for the source MAC
filter according to firmware spec 1.7.1.
In the original firmware spec. before 1.7.1, the VF spoof check flags
were not latched after making the HWRM_FUNC_CFG call, so there was a
need to keep the func_flags so that subsequent calls would perserve
the VF spoof check setting. A change was made in the 1.7.1 spec
so that the flags became latched. So we now set or clear the anti-
spoof setting directly without retrieving the old settings in the
stored vf->func_flags which are no longer valid. We also remove the
unneeded vf->func_flags.
Fixes: 8eb992e876 ("bnxt_en: Update firmware interface spec to 1.7.6.2.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b1 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware command returns error code as HWRM_ERR_CODE_BUSY, which
means it cannot handle the command due to a conflicting command
from another function, convert it to -EAGAIN. If it is an ethtool
operation, this error code will be returned to userspace.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return code is not needed in some of these functions, as the return
code from firmware message is ignored. Remove the unused rc variable
and also convert functions to void.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver stores a copy of the DCB settings that have been applied to
the firmware. After firmware reset, the firmware settings are gone and
will revert back to default. Clear the driver's copy so that if there
is a DCBNL request to get the settings, the driver will retrieve the
current settings from the firmware. lldpad keeps the DCB settings in
userspace and will re-apply the settings if it is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in continuous NAPI polling mode, the current code in
bnxt_poll_p5() will only process the completion rings and will not
process the NQ until interrupt is re-enabled. Tis logic works and
will not cause RX or TX starvation, but async events in the NQ may
be delayed for the duration of continuous NAPI polling. These
async events may be firmware or VF events.
Continue to handle the NQ after we are done polling the completion
rings. This actually simplies the code in bnxt_poll_p5().
Acknowledge the NQ so these async events will not overflow.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the function by removing tha 'all' parameter. In the current
code, the caller has to specify whether to update/arm both completion
rings with the 'all' parameter.
Instead of this, we can just update/arm all the completion rings
that have been polled. By setting cpr->had_work_done earlier in
__bnxt_poll_work(), we know which completion ring has been polled
and can just update/arm all the completion rings with
cpr->had_work_done set.
This simplifies the function with one less parameter and works just
as well.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_poll_p5(), the logic polls for up to 2 completion rings (RX and
TX) for work. In the current code, if we reach budget polling the
first completion ring, we will stop. If the other completion ring
has work to do, we will handle it when NAPI calls us back.
This is not optimal. We potentially leave an unproceesed entry in
the NQ. When we are finally done with NAPI polling and re-enable
interrupt, the remaining entry in the NQ will cause interrupt to
be triggered immediately for no reason.
Modify the code in bnxt_poll_p5() to keep looping until all NQ
entries are handled even if the first completion ring has reached
budget.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
Use of put_unaligned_le64 should be correct. pci_get_dsn() will perform
two pci_read_config_dword calls. The first dword will be placed in the
first 32 bits of the u64, while the second dword will be placed in the
upper 32 bits of the u64.
On Little Endian systems, the least significant byte comes first, which
will be the least significant byte of the first dword, followed by the
least significant byte of the second dword. Since the _le32 variations
do not perform byte swapping, we will correctly copy the dwords into the
dsn[] array in the same order as before.
On Big Endian systems, the most significant byte of the second dword
will come first. put_unaligned_le64 will perform a CPU_TO_LE64, which
will swap things correctly before copying. This should also end up with
the correct bytes in the dsn[] array.
While at it, fix a small typo in the netdev_info error message when the
DSN cannot be read.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
v3: adjust commit message for new member name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After bnxt_hwrm_do_send_message() was updated to return standard error
codes in a recent commit, a regression in bnxt_flash_package_from_file()
was introduced. The return value does not properly reflect all
possible firmware errors when calling firmware to flash the package.
Fix it by consolidating all errors in one local variable rc instead
of having 2 variables for different errors.
Fixes: d4f1420d36 ("bnxt_en: Convert error code in firmware message response to standard code.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If crashed kernel does not shutdown the NIC properly, PCIe FLR
is required in the kdump kernel in order to initialize all the
functions properly.
Fixes: d629522e1d ("bnxt_en: Reduce memory usage when running in kdump kernel.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Especially when bnxt_shutdown() is called during kexec, we need to
disable MSIX and disable Bus Master to completely quiesce the device.
Make these 2 calls unconditionally in the shutdown method.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently only calls netdev_set_tc_queue when the number of
TCs is greater than 1. Instead, the comparison should be greater than
or equal to 1. Even with 1 TC, we need to set the queue mapping.
This bug can cause warnings when the number of TCs is changed back to 1.
Fixes: 7809592d3e ("bnxt_en: Enable MSIX early in bnxt_init_one().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current logic that calls pci_disable_device() in __bnxt_close_nic()
during firmware reset is flawed. If firmware is still alive, we're
disabling the device too early, causing some firmware commands to
not reach the firmware.
Fix it by moving the logic to bnxt_reset_close(). If firmware is
in fatal condition, we call pci_disable_device() before we free
any of the rings to prevent DMA corruption of the freed rings. If
firmware is still alive, we call pci_disable_device() after the
last firmware message has been sent.
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after
firmware reset. Re-enabling SRIOV may consume all the resources and
may cause the RDMA driver to fail to get MSIX and other resources.
Fix it by calling bnxt_ulp_start() first before calling
bnxt_reenable_sriov().
We re-arrange the logic so that we call bnxt_ulp_start() and
bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and
bnxt_open(). The former is the normal coordinated firmware reset sequence
and the latter is firmware reset while the function is down. This new
logic is now more straight forward and will now fix both scenarios.
Fixes: f3a6d206c2 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.")
Reported-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
