If firmware is in reset or in bad state, it won't be able to return
VPD data. Move bnxt_vpd_read_info() until after bnxt_fw_init_one_p1()
successfully returns. By then we would have established proper
communications with the firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first HWRM_VER_GET message to firmware during probe may timeout if
firmware is under reset. This can happen during hot-plug for example.
On P5 and newer chips, we can check if firmware is in the boot stage by
reading a status register. Retry 5 times if the status register shows
that firmware is not ready and not in error state.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing support for handling NO_MASTER crashes while ports are
administratively down (ifdown). On some SoC platforms, the driver
needs to assist the firmware to recover from a crash via OP-TEE.
This is performed in a similar fashion to what is done during driver
probe.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define macros to check for the various states in the lower 16 bits of
the health register. Replace the C code that checks for these values
with the newly defined macros.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Updates to backing store APIs, QoS profiles, and push buffer initial
index support.
Since the new HWRM_FUNC_BACKING_STORE_CFG message size has increased,
we need to add some compat. logic to fall back to the smaller legacy
size if firmware cannot accept the larger message size. The new fields
added to the structure are not used yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the FW tells the driver to retry the INSTALL_UPDATE command after
it has cleared the NVM area, the driver is not clearing the previously
used ALLOWED_TO_DEFRAG flag. As a result the FW tries to defrag the NVM
area a second time in a loop and can fail the request.
Fixes: 1432c3f6a6 ("bnxt_en: Retry installing FW package under NO_SPACE error condition.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e9 ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes: ac3158cb01 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current scheme allocates a DMA buffer as big as the requested
firmware package file and DMAs the contents to firmware in one
operation. The buffer size can be several hundred kilo bytes and
the driver may not be able to allocate the memory. This will cause
firmware upgrade to fail.
Improve the scheme by using smaller DMA blocks and calling firmware to
DMA each block in a batch mode. Older firmware can cause excessive
NVRAM erases if the block size is too small so we try to allocate a
256K buffer to begin with and size it down successively if we cannot
allocate the memory.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bnxt_flash_package_from_fw_obj(), if firmware returns the NO_SPACE
error, call __bnxt_flash_nvram() to create the UPDATE directory and
then loop back and retry one more time.
Since the first try may fail, we use the silent version to send the
firmware commands.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On NICs with a smaller NVRAM, FW installation may fail after multiple
updates due to fragmentation. The driver can retry when FW returns
a special error code. To faciliate the retry, we restructure the
logic that performs the flashing in a loop. The actual retry logic
will be added in the next patch.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function will be modified in the next patch to retry flashing
the firmware in a loop. To facilate that, we rearrange the code so
that the steps that only need to be done once before the loop will be
moved to the top of the function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor bnxt_flash_nvram() into __bnxt_flash_nvram() that takes an
additional dir_item_len parameter. The new function will be used
in subsequent patches with the dir_item_len parameter set to create
the UPDATE directory during flashing.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jump to init_err_release to cleanup. bnxt_unmap_bars() will also be
called but it will do nothing if the BARs are not mapped yet.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1605858271-8209-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605792621-6268-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c213eae8d3 ("bnxt_en: Improve VF/PF link change logic.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605701851-20270-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.
Fixes: 4933f6753b ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_add_one_ctr() adds a hardware counter to a software counter and
adjusts for the hardware counter wraparound against the mask. The logic
assumes that the hardware counter is always smaller than or equal to
the mask.
This assumption is mostly correct. But in some cases if the firmware
is older and does not provide the accurate mask, the driver can use
a mask that is smaller than the actual hardware mask. This can cause
some extra carry bits to be added to the software counter, resulting in
counters that far exceed the actual value. Fix it by masking the
hardware counter with the mask passed into bnxt_add_one_ctr().
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4c ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the commit b148bb238c
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59c ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds FW versions stored in the flash to devlink info_get
callback. Return the correct fw.psid running version using the
newly added bp->nvm_cfg_ver.
v2:
Ensure stored pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
If the FW call to get stored version fails for any reason, return
success immediately to devlink without the stored versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-10-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new function bnxt_dl_info_put() to simplify the code, as there
are more stored firmware version fields to be added in the next patch.
Also, rename fw_ver variable name to ncsi_ver for better naming while
copying to devlink info_get cb.
v2:
Ensure active_pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-9-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command. Use it to
get the running version of the NVM configuration information.
This new function will also be used in subsequent patches to get the
stored firmware versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
event_data1 and event_data2 are used when processing most events.
Store these in local variables at the beginning of the function to
simplify many of the case statements.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-5-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, bp->msg_enable has default value of 0. It is more useful
to have the commonly used NETIF_MSG_DRV and NETIF_MSG_HW enabled by
default.
v2: Change the fall back bnxt_reset_task() inside bnxt_rx_ring_reset()
to silent mode. With older fw, we would take the fall back path and
it would be very noisy.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-4-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If NVRAM resources are locked, NVM writes are not permitted. In such
scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to
firmware commands.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-2-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver will schedule RX ring reset when we get a buffer
error in the RX completion record. These RX buffer errors can be due
to normal out-of-buffer conditions or a permanent error in the RX
ring. Because the driver cannot distinguish between these 2
conditions, we assume all these buffer errors require reset.
This is very disruptive when it is just a normal out-of-buffer
condition. Newer firmware will now monitor the rings for the permanent
failure and will send a notification to the driver when it happens.
This allows the driver to reset only when such a notification is
received. In environments where we have predominently out-of-buffer
conditions, we now can avoid these unnecessary resets.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is logic in the RX path to detect unexpected handles in the
RX completion. We'll print a warning and schedule a reset. The
next expected handle is then set to 0xffff which is guaranteed to
not match any valid handle. This will force all remaining packets in
the ring to be discarded before the reset. There can be hundreds of
these packets remaining in the ring and there is no need to print the
warnings for these forced errors.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per ring rx_resets counter to count these RX resets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some older chips, it is necessary to do a reset when we get buffer
errors associated with an RX ring. These buffer errors may become
frequent if the RX ring underruns under heavy traffic. The current
code does a global reset of all reasources when this happens. This
works but creates a big disruption of all rings when one RX ring is
having problem. This patch implements a localized RX ring reset of
just the RX ring having the issue. All other rings including all
TX rings will not be affected by this single RX ring reset.
Only the older chips prior to the P5 class supports this reset.
Because it is not a global reset, packets may still be arriving
while we are calling firmware to reset that ring. We need to be
sure that we don't post any buffers during this time while the
ring is undergoing reset. After firmware completes successfully,
the ring will be in the reset state with no buffers and we can start
filling it with new buffers and posting them.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_init_one_rx_ring() includes logic to initialize the BDs for one RX
ring and to allocate the buffers. Separate the allocation logic into a
new bnxt_alloc_one_rx_ring() function. The allocation function will be
used later to allocate new buffers for one specified RX ring when we
reset that RX ring.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_free_rx_skbs() frees all the allocated buffers and SKBs for
every RX ring. Refactor this function by calling a new function
bnxt_free_one_rx_ring_skbs() to free these buffers on one specified
RX ring at a time. This is preparation work for resetting one RX
ring during run-time.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware does not come out of reset, log FW health status info
to provide more information on firmware status.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NS3 SoC platforms require assistance from the OP-TEE to recover
firmware if a crash occurs while no driver is bound. The
CRASHED_NO_MASTER condition is recorded in the firmware status register
during the crash to indicate when driver intervension is needed to
coordinate a firmware reload. This condition is detected during early
driver initialization in order to effect a firmware fastboot on
supported platforms when necessary.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now supports device independent discovery of the status
register location. This status register can provide more detailed
information about firmware errors, especially if problems occur
before the HWRM interface is functioning. Attempt to map this
register if it is present and report the firmware status on firmware
init failures.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocator for the firmware health structure conflates allocation
and capability checks, limiting the reusability of the code. This patch
separates out the capability check and disablement and improves the
warning message to better describe the consequences of an allocation
failure.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes is to extend hwrm_nvm_get_dev_info_output() for stored
firmware versions and a new flag is added to fw_status_reg.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic that calculates the preset maximum value for combined
channel does not take into account the rings used for XDP and mqprio
TCs. Each of these features will reduce the number of TX rings. Add
the logic to divide the TX rings accordingly based on whether the
device is currently in XDP mode and whether TCs are in use.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port. Firmware
will send notification to the driver for the disabled port when this
happens. Define a new field in the link_info structure to keep track
of this state. The new phy_state field replaces the unused loop_back
field.
Log a message when the phy_state changes state. In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool PAM4 link modes for:
50000baseCR_Full
100000baseCR2_Full
200000baseCR4_Full
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware interface has added support for new link speeds using
PAM4 modulation. Expand the bnxt_link_info structure to closely
mirror the new firmware structures. Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.
Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong flag value caused the firmware call to return actual port
counters instead of the counter masks. This messed up the counter
overflow logic and caused erratic extended port counters to be
displayed under ethtool -S.
Fixes: 531d1d269c ("bnxt_en: Retrieve hardware masks for port counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix it to set the required fid input parameter. The firmware call
fails without this patch.
Fixes: d752d0536c ("bnxt_en: Retrieve hardware counter masks from firmware if available.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug firmware commands are not supported on VFs to read registers.
This patch avoids logging unnecessary access_denied error on VFs
when user calls ETHTOOL_GREGS.
By returning error in get_regs_len() method on the VF, the get_regs()
method will not be called.
Fixes: b5d600b027 ("bnxt_en: Add support for 'ethtool -d'")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All changes related to bp->link_info require the protection of the
link_lock mutex. It's not sufficient to rely just on RTNL.
Fixes: 163e9ef636 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning "unknown" as a temperature value violates the hwmon interface
rules. Appropriate error codes should be returned via device_attribute
show instead. These will ultimately be propagated to the user via the
file system interface.
In addition to the corrected error handling, it is an even better idea to
not present the sensor in sysfs at all if it is known that the read will
definitely fail. Given that temp1_input is currently the only sensor
reported, ensure no hwmon registration if TEMP_MONITOR_QUERY is not
supported or if it will fail due to access permissions. Something smarter
may be needed if and when other sensors are added.
Fixes: 12cce90b93 ("bnxt_en: fix HWRM error when querying VF temperature")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using strlcpy() to copy from VPD is not correct because VPD strings
are not necessarily NULL terminated. Use memcpy() to copy the VPD
length up to the destination buffer size - 1. The destination is
zeroed memory so it will always be NULL terminated.
Fixes: a0d0fd70fe ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These stats are already reported in ethtool -S.
Michael confirms they are equivalent to standard stats.
v2: - fix sparse warning about endian by using the macro
- use u64 for pointer type
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow drivers to call napi_hash_del() before calling
netif_napi_del() to batch RCU grace periods. This makes
the API asymmetric and leaks internal implementation details.
Soon we will want the grace period to protect more than just
the NAPI hash table.
Restructure the API and have drivers call a new function -
__netif_napi_del() if they want to take care of RCU waits.
Note that only core was checking the return status from
napi_hash_del() so the new helper does not report if the
NAPI was actually deleted.
Some notes on driver oddness:
- veth observed the grace period before calling netif_napi_del()
but that should not matter
- myri10ge observed normal RCU flavor
- bnx2x and enic did not actually observe the grace period
(unless they did so implicitly)
- virtio_net and enic only unhashed Rx NAPIs
The last two points seem to indicate that the calls to
napi_hash_del() were a left over rather than an optimization.
Regardless, it's easy enough to correct them.
This patch may introduce extra synchronize_net() calls for
interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on
free_netdev() to call netif_napi_del(). This seems inevitable
since we want to use RCU for netpoll dev->napi_list traversal,
and almost no drivers set IFF_DISABLE_NETPOLL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() which runs from a workqueue can race with
bnxt_remove_one(). For example, if firmware reset and VF FLR are
happening at about the same time.
bnxt_remove_one() already cancels the workqueue and waits for it
to finish, but we need to do this earlier before the devlink
reporters are destroyed. This will guarantee that
the devlink reporters will always be valid when bnxt_fw_reset_task()
is still running.
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver goes through PCIe AER reset in error state, all
firmware messages will timeout because the PCIe bus is no longer
accessible. This can lead to AER reset taking many minutes to
complete as each firmware command takes time to timeout.
Define a new macro BNXT_NO_FW_ACCESS() to skip these firmware messages
when either firmware is in fatal error state or when
pci_channel_offline() is true. It now takes a more reasonable 20 to
30 seconds to complete AER recovery.
Fixes: b4fff2079d ("bnxt_en: Do not send firmware messages if firmware is in error state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4 ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d8 ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.
Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.
Fixes: 125592fbf4 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory, so memset is not needed
dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump PXP registers and PCIe statistics.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.
A chip bug was also discovered that could cause some ring counters to
become 0 during DMA. Workaround by ignoring zeros on the affected
chips.
Some older frimware will reset port counters during ifdown. We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported by newer firmware, make the firmware call to query all
the port counter masks. If not supported, assume 40-bit port
counter masks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters. Make this call when supported to
initialize the hardware masks of all ring counters. If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow. Allocate copies of these
DMA statistics memory blocks with the same size for accumulation. The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.
There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that NETIF_F_HW_TC is not set should be a sufficient
indication to the user that TC offloads are not supported.
No need to bother users of older firmware versions with
pointless warnings on every boot.
Also, since the support is optional, bnxt_init_tc() should not
return an error in case FW is old, similarly to how error
is not returned when CONFIG_BNXT_FLOWER_OFFLOAD is not set.
With that we can add an error message to the caller, to warn
about actual unexpected failures.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current completion ring sizing formula is wrong with TPA enabled.
The formula assumes that the number of TPA completions are bound by the
RX ring size, but that's not true. TPA_START completions are immediately
recycled so they are not bound by the RX ring size. We must add
bp->max_tpa to the worst case maximum RX and TPA completions.
The completion ring can overflow because of this mistake. This will
cause hardware to disable the completion ring when this happens,
leading to RX and TX traffic to stall on that ring. This issue is
generally exposed only when the RX ring size is set very small.
Fix the formula by adding bp->max_tpa to the number of RX completions
if TPA is enabled.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.");
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a shared port PHY configuration, async event is received when any of the
port modifies the configuration. Ethtool link settings should be
initialised after updated PHY configuration from firmware.
Fixes: b1613e78e9 ("bnxt_en: Add async. event logic for PHY configuration changes.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago. The pause setting was missed when
making that change. Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().
Fixes: e2dc9b6e38 ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new infra, taking advantage of sleeping in callbacks.
v2:
- use bp->*_fw_dst_port_id != INVALID_HW_RING_ID as indication
that the offload is active.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare-metal use cases require giving firmware and the embedded
application processor control over VLAN offloads. The driver should
not attempt to override or utilize this feature in such scenarios
since it will not work as expected.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware VLAN offload feature on our NIC does not have separate
knobs for handling customer and service tags on RX. Either offloading
of both must be enabled or both must be disabled. Introduce definitions
for the combined feature set in order to clean up the code and make
this constraint more clear. Technically these features can be separately
enabled on TX, however, since the default is to turn both on, the
combined TX feature set is also introduced for code consistency.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new infrastructure in place, we can now support the setting of
the indirection table from ethtool.
When changing channels, in a rare case that firmware cannot reserve the
rings that were promised, we will still try to keep the RSS map and only
revert to default when absolutely necessary.
v4: Revert RSS map to default during ring change only when absolutely
necessary.
v3: Add warning messages when firmware cannot reserve the requested RX
rings, and when the RSS table entries have to change to default.
v2: When changing channels, if the RSS table size changes and RSS map
is non-default, return error.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the logical indirection table, we can return these
proper logical indices directly to ethtool -x instead of the physical
IDs.
Reported-by: Jakub Kicinski <kicinski@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the logical table, we can fill the HW RSS table
using the logical table's entries and converting them to the HW
specific format. Re-initialize the logical table to standard
distribution if the number of RX rings changes during ring reservation.
v4: Use bnxt_get_rxfh_indir_size() to get the RSS table size.
v2: Use ALIGN() to roundup the RSS table size.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some chips, this varies based on the number of RX rings. Add this
helper function and refactor the existing code to use it.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently does not keep track of the logical RSS indirection
table. The hardware RSS table is set up with standard default ring
distribution when initializing the chip. This makes it difficult to
support user sepcified indirection table entries. As a first step, add
the logical table in the main bnxt structure and allocate it according
to chip specific table size. Add a function that sets up default
RSS distribution based on the number of RX rings.
v4: Use bnxt_get_rxfh_indir_size() for the current RSS table size.
v2: Use kmalloc_array() since we init. all entries afterwards.
Use ALIGN() to roundup the RSS table size.
Use ethtool_rxfh_indir_default() to init. the default entries.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up bnxt_get_rxfh_indir_size() to return the proper current RSS
table size for P5 chips. Change it to non-static so that bnxt.c
can use it to get the table size.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we allocate one page for the hardware DMA RSS indirection
table. While the size is currently big enough for all chips, future
chip variations may support bigger sizes, so it is better to calculate
and store the chip specific size and allocate accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual functions does not have VPD information. This patch modifies
calling bnxt_read_vpd_info() only for PFs and avoids an unnecessary
error log.
Fixes: a0d0fd70fe ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older firmware, the hardware statistics are not cleared when the
driver frees the hardware stats contexts during ifdown. The driver
expects these stats to be cleared and saves a copy before freeing
the stats contexts. During the next ifup, the driver will likely
allocate the same hardware stats contexts and this will cause a big
increase in the counters as the old counters are added back to the
saved counters.
We fix it by making an additional firmware call to clear the counters
before freeing the hw stats contexts when the firmware is the older
20.x firmware.
Fixes: b8875ca356 ("bnxt_en: Save ring statistics before reset.")
Reported-by: Jakub Kicinski <kicinski@fb.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jakub Kicinski <kicinski@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware may not support legacy TX push properly and may not
be disabling it. So we check certain firmware versions that may
have this problem and disable legacy TX push unconditionally.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only store the firmware version as a string for ethtool
and devlink info. Store it also as a version code. The next 2
patches will need to check the firmware major version to determine
some workarounds.
We also use the 16-bit firmware version fields if the firmware is newer
and provides the 16-bit fields.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add board.serial_number field info to info_get cb via devlink,
if driver can fetch the information from the device.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path.
Fixes: 1fac52da59 ("net: flow_offload: consolidate indirect flow_block infrastructure")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare fix the bug in the next patch. use flow_indr_block_cb_alloc/remove
function and remove the __flow_block_indr_binding.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will avoid many uneccessary error logs when driver or firmware is
in reset.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AER reset should follow the same steps as suspend/resume. We need to
free context memory during AER reset and allocate new context memory
during recovery by calling bnxt_hwrm_func_qcaps(). We also need
to call bnxt_reenable_sriov() to restore the VFs.
Fixes: bae361c54f ("bnxt_en: Improve AER slot reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are enabled, we need to re-configure them during resume because
firmware has been reset while resuming. Otherwise, the VFs won't
work after resume.
Fixes: c16d4ee0e3 ("bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separate steps we do in bnxt_resume() can be done more simply by
calling bnxt_hwrm_func_qcaps(). This change will add an extra
__bnxt_hwrm_func_qcaps() call which is needed anyway on older
firmware.
Fixes: f9b69d7f62 ("bnxt_en: Fix suspend/resume path on 57500 chips")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
The explicit mask and shift is not the appropriate way to parse fields
out of a little endian struct. The length field is internally __le16
and the strategy employed only happens to work on little endian machines
because the offset used is actually incorrect (length is at offset 6).
Also remove the related and no longer used definitions from bnxt.h.
Fixes: 845adfe40c ("bnxt_en: Improve valid bit checking in firmware response message.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NVRAM directory is not found, return the error code
properly as per firmware command failure instead of the hardcode
-ENOBUFS.
Fixes: 3a707bed13 ("bnxt_en: Return -EAGAIN if fw command returns BUSY")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have logic to maintain network counters across resets by storing
the counters in bp->net_stats_prev before reset. But not all resets
will clear the counters. Certain resets that don't need to change
the number of rings do not clear the counters. The current logic
accumulates the counters before all resets, causing big jumps in
the counters after some resets, such as ethtool -G.
Fix it by only accumulating the counters during reset if the irq_re_init
parameter is set. The parameter signifies that all rings and interrupts
will be reset and that means that the counters will also be reset.
Reported-by: Vijayendra Suman <vijayendra.suman@oracle.com>
Fixes: b8875ca356 ("bnxt_en: Save ring statistics before reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses full PAGE_SIZE pages when XDP is enabled.
In case of XDP uses driver uses __bnxt_alloc_rx_page which does full
page DMA-map. Thus, xdp_adjust_tail grow is DMA compliant for XDP_TX
action that does DMA-sync.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Link: https://lore.kernel.org/bpf/158945334769.97035.13437970179897613984.stgit@firesoul
Fix the following coccicheck warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1991:5-46: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1993:10-54: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2380:5-38: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool -S shows all TX/RX ring counters whether the
channel is combined, RX, or TX. The unused counters will always be
zero. Improve it by showing only the relevant counters if the channel
is RX or TX. If the channel is combined, the counters will be shown
exactly the same as before.
[ MChan: Lots of cleanups and simplifications on Rajesh's original
code]
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the RX and TX ring statistics to be separated if needed.
In the next patch, we'll be able to only display RX or TX statistcis if
the channel is RX only or TX only.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have 3 software ring counters, rx_l4_csum_errors,
rx_buf_errors, and missed_irqs. The 1st two are RX counters and the
last one is a common counter. Organize them into 2 structures
bnxt_rx_sw_stats and bnxt_cmn_sw_stats.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this is to inform the RDMA driver the size of the doorbell
BAR that the L2 driver has mapped and the portion that is mapped
uncacheable. The unchaeable portion is shared with the RoCE driver.
Any remaining unmapped doorbell BAR can be used by the RDMA driver for
its own purpose. Currently, the entire L2 portion is mapped uncacheable.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the L2 doorbell size from the firmware and only map the portion
of the doorbell BAR for L2 use. This will leave the remaining doorbell
BAR available for the RoCE driver to use. The RoCE driver can map
the remaining portion as write-combining to support the push feature.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver provides completion ring or NQ doorbell offset for each
MSIX entry requested by the RDMA driver. The NQ offset on 57500
chips is different than legacy chips. Set it correctly based on
chip type for correctness. The RDMA driver is ignoring this field
for the 57500 chips so it is not causing any problem.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the 57500 chip doorbell offsets instead of using the magic
values in the C file.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel log messages for failed AP reset commands should be suppressed.
These are expected to fail on devices that do not have an AP. Add
missing driver reload message after AP reset and log it in a common
way without duplication.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool ABI specifies that the reset operation should only clear
the flags that were actually reset. Setting the flags to zero after
a chip reset violates this because it does not include resetting the
application processor complex. Similarly, components that are not yet
defined are also not necessarily being reset.
The fact that chip reset does not cover the AP also means that it is
inappropriate to treat these two components exclusively of one another.
The ABI provides a mechanism to report a failure to reset independent
components via the returned bitmask, so it is also wrong to fail hard
if one of a set of independent resets is not possible.
It is incorrect to rely on the passed by reference flags in bnxt_reset(),
which are being updated as components are reset. The initially requested
value should be used instead so that hard errors do not propagate if any
earlier components could have been reset successfully.
Note, AP and chip resets are global in nature. Dedicated resets are
thus not currently supported.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The case statement in bnxt_firmware_reset() dangerously mixes types.
This patch separates the application processor and whole chip resets
from the rest such that the selection is performed on a pure type.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract bnxt_hwrm_firmware_reset() for performing firmware reset
operations. This new helper function will be used in a subsequent
patch to separate unrelated reset types out of bnxt_firmware_reset().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware does not expect the CRC to be included in the length
passed from the driver. The firmware always configures the chip
to strip out the CRC.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current formulas to calculate the TQM slow path and fast path ring
context memory sizes are not quite correct. TQM slow path entry is
array index 0 of ctx->tqm_mem[]. The other array entries are for fast
path. Fix these sizes according to latest firmware spec. for 57500 and
newer chips.
Fixes: 3be8136ce1 ("bnxt_en: Initialize context memory to the value specified by firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware spec. will specify the number of TQM rings to allocate
context memory for. Use the firmware specified value and fall back
to the old value derived from bp->max_q if it is not available.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes include additional statistics, ECN support, context memory
interface change for better TQM context memory sizing, firmware
health status definitions, etc.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic in bnxt_fix_features() will inadvertently turn on both
CTAG and STAG VLAN offload if the user tries to disable both. Fix it
by checking that the user is trying to enable CTAG or STAG before
enabling both. The logic is supposed to enable or disable both CTAG and
STAG together.
Fixes: 5a9f6b238e ("bnxt_en: Enable and disable RX CTAG and RX STAG VLAN acceleration together.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_alloc_ctx_pg_tbls() should return error when the memory size of the
context memory to set up is zero. By returning success (0), the caller
may proceed normally and may crash later when it tries to set up the
memory.
Fixes: 08fe9d1816 ("bnxt_en: Add Level 2 context memory paging support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the slot reset sequence by disabling the device to prevent bad
DMAs if slot reset fails. Return the proper result instead of always
PCI_ERS_RESULT_RECOVERED to the caller.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom adapters support only maximum of 512 CQs per PF. If user sets
MSIx vectors more than supported CQs, firmware is setting incorrect value
for msix_vec_per_pf_max parameter. Fix it by reducing the BNXT_MSIX_VEC_MAX
value to 512, even though the maximum # of MSIx vectors supported by adapter
are 1280.
Fixes: f399e84978 ("bnxt_en: Use msix_vec_per_pf_max and msix_vec_per_pf_min devlink params.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic that sets the enable/disable flag for the source MAC
filter according to firmware spec 1.7.1.
In the original firmware spec. before 1.7.1, the VF spoof check flags
were not latched after making the HWRM_FUNC_CFG call, so there was a
need to keep the func_flags so that subsequent calls would perserve
the VF spoof check setting. A change was made in the 1.7.1 spec
so that the flags became latched. So we now set or clear the anti-
spoof setting directly without retrieving the old settings in the
stored vf->func_flags which are no longer valid. We also remove the
unneeded vf->func_flags.
Fixes: 8eb992e876 ("bnxt_en: Update firmware interface spec to 1.7.6.2.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b1 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add part number info from the vital product data to info_get command
via devlink tool. Update bnxt.rst documentation as well.
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other drivers, properly clear the devlink port type when
removing the device before unregistration.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware command returns error code as HWRM_ERR_CODE_BUSY, which
means it cannot handle the command due to a conflicting command
from another function, convert it to -EAGAIN. If it is an ethtool
operation, this error code will be returned to userspace.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return code is not needed in some of these functions, as the return
code from firmware message is ignored. Remove the unused rc variable
and also convert functions to void.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver stores a copy of the DCB settings that have been applied to
the firmware. After firmware reset, the firmware settings are gone and
will revert back to default. Clear the driver's copy so that if there
is a DCBNL request to get the settings, the driver will retrieve the
current settings from the firmware. lldpad keeps the DCB settings in
userspace and will re-apply the settings if it is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in continuous NAPI polling mode, the current code in
bnxt_poll_p5() will only process the completion rings and will not
process the NQ until interrupt is re-enabled. Tis logic works and
will not cause RX or TX starvation, but async events in the NQ may
be delayed for the duration of continuous NAPI polling. These
async events may be firmware or VF events.
Continue to handle the NQ after we are done polling the completion
rings. This actually simplies the code in bnxt_poll_p5().
Acknowledge the NQ so these async events will not overflow.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the function by removing tha 'all' parameter. In the current
code, the caller has to specify whether to update/arm both completion
rings with the 'all' parameter.
Instead of this, we can just update/arm all the completion rings
that have been polled. By setting cpr->had_work_done earlier in
__bnxt_poll_work(), we know which completion ring has been polled
and can just update/arm all the completion rings with
cpr->had_work_done set.
This simplifies the function with one less parameter and works just
as well.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_poll_p5(), the logic polls for up to 2 completion rings (RX and
TX) for work. In the current code, if we reach budget polling the
first completion ring, we will stop. If the other completion ring
has work to do, we will handle it when NAPI calls us back.
This is not optimal. We potentially leave an unproceesed entry in
the NQ. When we are finally done with NAPI polling and re-enable
interrupt, the remaining entry in the NQ will cause interrupt to
be triggered immediately for no reason.
Modify the code in bnxt_poll_p5() to keep looping until all NQ
entries are handled even if the first completion ring has reached
budget.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
Use of put_unaligned_le64 should be correct. pci_get_dsn() will perform
two pci_read_config_dword calls. The first dword will be placed in the
first 32 bits of the u64, while the second dword will be placed in the
upper 32 bits of the u64.
On Little Endian systems, the least significant byte comes first, which
will be the least significant byte of the first dword, followed by the
least significant byte of the second dword. Since the _le32 variations
do not perform byte swapping, we will correctly copy the dwords into the
dsn[] array in the same order as before.
On Big Endian systems, the most significant byte of the second dword
will come first. put_unaligned_le64 will perform a CPU_TO_LE64, which
will swap things correctly before copying. This should also end up with
the correct bytes in the dsn[] array.
While at it, fix a small typo in the netdev_info error message when the
DSN cannot be read.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
v3: adjust commit message for new member name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After bnxt_hwrm_do_send_message() was updated to return standard error
codes in a recent commit, a regression in bnxt_flash_package_from_file()
was introduced. The return value does not properly reflect all
possible firmware errors when calling firmware to flash the package.
Fix it by consolidating all errors in one local variable rc instead
of having 2 variables for different errors.
Fixes: d4f1420d36 ("bnxt_en: Convert error code in firmware message response to standard code.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing newlines to netdev_* format strings so the lines
aren't buffered by the printk subsystem.
Nitpicked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If crashed kernel does not shutdown the NIC properly, PCIe FLR
is required in the kdump kernel in order to initialize all the
functions properly.
Fixes: d629522e1d ("bnxt_en: Reduce memory usage when running in kdump kernel.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Especially when bnxt_shutdown() is called during kexec, we need to
disable MSIX and disable Bus Master to completely quiesce the device.
Make these 2 calls unconditionally in the shutdown method.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently only calls netdev_set_tc_queue when the number of
TCs is greater than 1. Instead, the comparison should be greater than
or equal to 1. Even with 1 TC, we need to set the queue mapping.
This bug can cause warnings when the number of TCs is changed back to 1.
Fixes: 7809592d3e ("bnxt_en: Enable MSIX early in bnxt_init_one().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current logic that calls pci_disable_device() in __bnxt_close_nic()
during firmware reset is flawed. If firmware is still alive, we're
disabling the device too early, causing some firmware commands to
not reach the firmware.
Fix it by moving the logic to bnxt_reset_close(). If firmware is
in fatal condition, we call pci_disable_device() before we free
any of the rings to prevent DMA corruption of the freed rings. If
firmware is still alive, we call pci_disable_device() after the
last firmware message has been sent.
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after
firmware reset. Re-enabling SRIOV may consume all the resources and
may cause the RDMA driver to fail to get MSIX and other resources.
Fix it by calling bnxt_ulp_start() first before calling
bnxt_reenable_sriov().
We re-arrange the logic so that we call bnxt_ulp_start() and
bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and
bnxt_open(). The former is the normal coordinated firmware reset sequence
and the latter is firmware reset while the function is down. This new
logic is now more straight forward and will now fix both scenarios.
Fixes: f3a6d206c2 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.")
Reported-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Put the current logic in bnxt_open() to re-enable SRIOV after detecting
firmware reset into a new function bnxt_reenable_sriov(). This call
needs to be invoked in the firmware reset path also in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Display the following information via devlink info command:
- Driver name
- Board id
- Broad revision
- Board Serial number
- Board FW version
- FW parameter set version
- FW App version
- FW management version
- FW RoCE version
Standard output example:
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver bnxt_en
serial_number 00-10-18-FF-FE-AD-05-00
versions:
fixed:
asic.id D802
asic.rev 1
running:
fw 216.1.124.0
fw.psid 0.0.0
fw.app 216.1.122.0
fw.mgmt 864.0.32.0
fw.roce 216.1.15.0
[ This version has incorporated changes suggested by Jakub Kicinski to
use generic devlink version tags. ]
v2: Use fw.psid
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of switch_id, renaming it to dsn will be more meaningful
so that it can be used to display device serial number in follow up
patch via devlink_info command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds status notification to devlink flash update
while flashing is in progress.
$ devlink dev flash pci/0000:05:00.0 file 103.pkg
Preparing to flash
Flashing done
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest kernels get the phys_port_name via devlink, if
ndo_get_phys_port_name is not defined. To provide the phys_port_name
correctly, register devlink before registering netdev.
Also call devlink_port_type_eth_set() after registering netdev as
devlink port updates the netdev structure and notifies user.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to register for devlink port and use port features.
Also register params only if firmware spec version is at least 0x10600
which will support reading/setting numbered variables in NVRAM.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define bnxt_dl_params_register() and bnxt_dl_params_unregister()
functions and move params register/unregister code to these newly
defined functions. This patch is in preparation to register
devlink irrespective of firmware spec. version in the next patch.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware bug has been fixed on B0 and newer chips, so disable the
workaround on these chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only time we check and remove expired filters is
when we are inserting new filters.
Improving the aRFS expiry handling by adding code to do the above
work periodically.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_rx_flow_steer(), if the dissected packet is a fragment, do not
proceed to create the ntuple filter and return error instead. Otherwise
we would create a filter with 0 source and destination ports because
the dissected ports would not be available for fragments.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
575XX (P5) chips have the same UDP RSS hashing capability as P4 chips,
so we can enable it on P5 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_port is meant to distinguish the network ports belonging to
the same PCI function. Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 2nd parameter fw_dflt is not set, we are calling bnxt_probe_phy()
after the firmware has reset. There is no need to query the current
PHY settings from firmware as these settings may be different from
the ethtool settings that the driver will re-establish later. So
return earlier in bnxt_probe_phy() to save one firmware call.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link. Instead, we should use bp->link_info.link_up
which has the true link state. The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.
By always using bp->link_info.link_up, the code is now more
consistent and more correct. Some unnecessary link toggles are
now prevented with this patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached. Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return EINPROGRESS to devlink health reporter recover as we are not yet
done and call devlink_health_reporter_recovery_done once reset is
successfully completed from workqueue context.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa71 ("bnxt_en: Update interrupt coalescing logic.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery. Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink. Only the PF
will register the devlink parameters. With devlink registered,
we can now create the health reporters on the VFs.
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the allocation of bp->fw_health in the previous patch,
the driver will not go through the fw reset and recovery code paths
if bp->fw_health allocation fails. So we can now remove the
unnecessary NULL checks.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bp->fw_health needs to be allocated for either the firmware initiated
reset feature or the driver initiated error recovery feature. The
current code is not allocating bp->fw_health for all the necessary cases.
This patch corrects the logic to allocate bp->fw_health correctly when
needed. If allocation fails, we clear the feature flags.
We also add the the missing kfree(bp->fw_health) when the driver is
unloaded. If we get an async reset message from the firmware, we also
need to make sure that we have a valid bp->fw_health before proceeding.
Fixes: 07f83d72d2 ("bnxt_en: Discover firmware error recovery capabilities.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323 ("bnxt_en: Keep track of reserved IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same bnxt_flash_package_from_file() function to support
devlink flash operation.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Currently, the driver does not allow PHY settings on a multi-function or
NPAR NIC whose port is shared by more than one function. Newer
firmware now allows PHY settings on some of these NICs. Check for
this new firmware setting and allow the user to set the PHY settings
accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If the link settings have been changed by another function sharing the
port, firmware will send us an async. message. In response, we will
call the new bnxt_init_ethtool_link_settings() function to update
the current settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Refactor this logic in bnxt_probe_phy() into a separate function
bnxt_init_ethtool_link_settings(). It used to be that the settable
link settings will never be changed without going through ethtool.
So we only needed to do this once in bnxt_probe_phy(). Now, another
function sharing the port may change it and we may need to re-initialize
the ethtool settings again in run-time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
New firmware allows PHY loopback to be set without disabling autoneg
first. Check this capability and skip disabling autoneg when
it is supported by firmware. Using this scheme, loopback will
always work even if the PHY only supports autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The driver currently only assignes 1 RSS context to each VF. This works
for the Linux VF driver. But other drivers, such as DPDK, can make use
of additional RSS contexts. Modify the code to divide up and assign
RSS contexts to VFs just like other resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Some chips that need host context memory as a backing store requires
the memory to be initialized to a non-zero value. Query the
value from firmware and initialize the context memory accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Driver calls HWRM_FUNC_RESET firmware call while resuming the device
which clears the context memory backing store. Because of which
allocating firmware resources would eventually fail. Fix it by freeing
all context memory during suspend and reallocate the memory during resume.
Call bnxt_hwrm_queue_qportcfg() in resume path. This firmware call
is needed on the 57500 chips so that firmware will set up the proper
queue mapping in relation to the context memory.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After driver unregister, firmware is erasing the information that
driver supports new resource management. Send FUNC_RESOURCE_QCAPS
command to inform the firmware that driver supports new resource
management while resuming from hibernation. Otherwise, we fallback
to the older resource allocation scheme.
Also, move driver register after sending FUNC_RESOURCE_QCAPS command
to be consistent with the normal initialization sequence.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Everytime driver registers with firmware, driver is required to
register for async event notifications as well. These 2 calls
are done using the same firmware command and can be combined.
We are also missing the 2nd step to register for async events
in the suspend/resume path and this will fix it. Prior to this,
we were getting only default notifications.
ULP can register for additional async events for the RDMA driver,
so we add a parameter to the new function to only do step 2 when
it is called from ULP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In the bnxt_init_one() failure path, if the driver has already called
firmware to register the driver, it is not undoing the driver
registration. Add this missing step to unregister for correctness,
so that the firmware knows that the driver has unloaded.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Disable Bus master during suspend to prevent DMAs after the device
goes into D3hot state. The new 57500 devices may continue to DMA
from context memory after the system goes into D3hot state. This
may cause some PCIe errors on some system. Re-enable it during resume.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Fix BNXT_CHIP_NUM_5645X() to include 57452 and 56454 chip IDs, so
that these chips will be properly classified as P4 chips to take
advantage of the P4 fixes and features.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
