Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the Lantiq
DSA switches and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII, Reverse MII and Reduced MII
links is handled within phylink_generic_validate() in phylink, so there
is no need to make them conditional on the interface mode in the driver.
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Populate the supported interfaces and MAC capabilities for the
hellcreek DSA switch and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
The switch actually only supports MII and RGMII, but as phylib defaults
to GMII, we need to include this interface mode to keep existing DT
working.
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Function mv88e6xxx_serdes_pcs_get_state() currently does not report link
up if AN is enabled, Link bit is set, but Speed and Duplex Resolved bit
is not set, which testing shows is the case for when auto-negotiation
was bypassed (we have AN enabled but link partner does not).
An example of such link partner is Marvell 88X3310 PHY, when put into
the mode where host interface changes between 10gbase-r, 5gbase-r,
2500base-x and sgmii according to copper speed. The 88X3310 does not
enable AN in 2500base-x, and so SerDes on mv88e6xxx currently does not
link with it.
Fix this.
Fixes: a5a6858b79 ("net: dsa: mv88e6xxx: extend phylink to Serdes PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inband AN is broken on Amethyst in 2500base-x mode when set by standard
mechanism (via cmode).
(There probably is some weird setting done by default in the switch for
this mode that make it cycle in some state or something, because when
the peer is the mvneta controller, it receives link change interrupts
every ~0.3ms, but the link is always down.)
Get around this by configuring the PCS mode to 1000base-x (where inband
AN works), and then changing the SerDes frequency while SerDes
transmitter and receiver are disabled, before enabling SerDes PHY. After
disabling SerDes PHY, change the PCS mode back to 2500base-x, to avoid
confusing the device (if we leave it at 1000base-x PCS mode but with
different frequency, and then change cmode to sgmii, the device won't
change the frequency because it thinks it already has the correct one).
The register which changes the frequency is undocumented. I discovered
it by going through all registers in the ranges 4.f000-4.f100 and
1e.8000-1e.8200 for all SerDes cmodes (sgmii, 1000base-x, 2500base-x,
5gbase-r, 10gbase-r, usxgmii) and filtering out registers that didn't
make sense (the value was the same for modes which have different
frequency). The result of this was:
reg sgmii 1000base-x 2500base-x 5gbase-r 10gbase-r usxgmii
04.f002 005b 0058 0059 005c 005d 005f
04.f076 3000 0000 1000 4000 5000 7000
04.f07c 0950 0950 1850 0550 0150 0150
1e.8000 0059 0059 0058 0055 0051 0051
1e.8140 0e20 0e20 0e28 0e21 0e42 0e42
Register 04.f002 is the documented Port Operational Confiuration
register, it's last 3 bits select PCS type, so changing this register
also changes the frequency to the appropriate value.
Registers 04.f076 and 04.f07c are not writable.
Undocumented register 1e.8000 was the one: changing bits 3:0 from 9 to 8
changed SerDes frequency to 3.125 GHz, while leaving the value of PCS
mode in register 04.f002.2:0 at 1000base-x. Inband autonegotiation
started working correctly.
(I didn't try anything with register 1e.8140 since 1e.8000 solved the
problem.)
Since I don't have documentation for this register 1e.8000.3:0, I am
using the constants without names, but my hypothesis is that this
register selects PHY frequency. If in the future I have access to an
oscilloscope able to handle these frequencies, I will try to test this
hypothesis.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fix for erratum 5.2 of the 88E6393X (Amethyst) family: for 10gbase-r
mode, some undocumented registers need to be written some special
values.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save power on 88E6393X by disabling SerDes receiver and transmitter
after SerDes is SerDes is disabled.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for lane is unnecessary, since the function is called only
with allowed lane argument.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to SERDES scripts for 88E6393X, erratum 4.8 has to be applied
every time before SerDes is powered on.
Split the code for erratum 4.8 into separate function and call it in
mv88e6393x_serdes_power().
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-length and one-element arrays are deprecated, see
Documentation/process/deprecated.rst
Flexible-array members should be used instead.
Generated by: scripts/coccinelle/misc/flexible_array.cocci
Fixes: 23ae3a7877 ("net: dsa: felix: add stream gate settings for psfp")
CC: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a shared MDIO access implementation by way of the mdio-mscc-miim
driver.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch seville to use of_mdiobus_register(bus, NULL) instead of just
mdiobus_register. This code is about to be pulled into a separate module
that can optionally define ports by the device_node.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A contact at Realtek has clarified what exactly the units of RGMII RX
delay are. The answer is that the unit of RX delay is "about 0.3 ns".
Take this into account when parsing rx-internal-delay-ps by
approximating the closest step value. Delays of more than 2.1 ns are
rejected.
This obviously contradicts the previous assumption in the driver that a
step value of 4 was "about 2 ns", but Realtek also points out that it is
easy to find more than one RX delay step value which makes RGMII work.
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Cc: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe deferral is not an error, so don't log this as an error:
[0.590156] realtek-smi ethernet-switch: unable to register switch ret = -517
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.
This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.
rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix warning reported by bot.
Make sure hash is init to 0 and fix wrong logic for hash_type in
qca8k_lag_can_offload.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: def975307c ("net: dsa: qca8k: add LAG support")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211123154446.31019-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LAG support to this switch. In Documentation this is described as
trunk mode. A max of 4 LAGs are supported and each can support up to 4
port. The current tx mode supported is Hash mode with both L2 and L2+3
mode.
When no port are present in the trunk, the trunk is disabled in the
switch.
When a port is disconnected, the traffic is redirected to the other
available port.
The hash mode is global and each LAG require to have the same hash mode
set. To change the hash mode when multiple LAG are configured, it's
required to remove each LAG and set the desired hash mode to the last.
An error is printed when it's asked to set a not supported hadh mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports mirror mode. Only one port can set as mirror port and
every other port can set to both ingress and egress mode. The mirror
port is disabled and reverted to normal operation once every port is
removed from sending packet to it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for mdb add/del function. The ARL table is used to insert
the rule. The rule will be searched, deleted and reinserted with the
port mask updated. The function will check if the rule has to be updated
or insert directly with no deletion of the old rule.
If every port is removed from the port mask, the rule is removed.
The rule is set STATIC in the ARL table (aka it doesn't age) to not be
flushed by fast age function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k support setting ageing time in step of 7s. Add support for it and
set the max value accepted of 7645m.
Documentation talks about support for 10000m but that values doesn't
make sense as the value doesn't match the max value in the reg.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports fast aging by flushing any rule in the ARL
table for a specific port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently missing 2 additionals MIB counter present in QCA833x
switch.
QC832x switch have 39 MIB counter and QCA833X have 41 MIB counter.
Add the additional MIB counter and rework the MIB function to print the
correct supported counter from the match_data struct.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert any qca8k set/clear/pool to regmap helper and add
missing config to regmap_config struct.
Read/write/rmw operation are reworked to use the regmap helper
internally to keep the delta of this patch low. These additional
function will then be dropped when the code split will be proposed.
Ipq40xx SoC have the internal switch based on the qca8k regmap but use
mmio for read/write/rmw operation instead of mdio.
In preparation for the support of this internal switch, convert the
driver to regmap API to later split the driver to common and specific
code. The overhead introduced by the use of regamp API is marginal as the
internal mdio will bypass it by using its direct access and regmap will be
used only by configuration functions or fdb access.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for regmap conversion, move regmap init in the probe
function and make it mandatory as any read/write/rmw operation will be
converted to regmap API.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mutex is already init in sw_probe. Remove the extra init in qca8k_setup.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert and try to standardize bit fields using
GENMASK/FIELD_PREP/FIELD_GET macros. Rework some logic to support the
standard macro and tidy things up. No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very next check for port 0 and 6 already makes sure we don't go out
of bounds with the ports_config delay table.
Remove the redundant check.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.
The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.
The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.
This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.
Fixes: cef0811584 ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSFP rules take effect on the streams from any port of VSC9959 switch.
This patch use ingress port to limit the rule only active on this port.
Each stream can only match two ingress source ports in VSC9959. Streams
from lowest port gets the configuration of SFID pointed by MAC Table
lookup and streams from highest port gets the configuration of (SFID+1)
pointed by MAC Table lookup. This patch defines the PSFP rule on highest
port as dummy rule, which means that it does not modify the MAC table.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add police action to set flow meter table which is defined
in IEEE802.1Qci. Flow metering is two rates two buckets and three color
marker to policing the frames, we only enable one rate one bucket in
this patch.
Flow metering shares a same policer pool with VCAP policers, so the PSFP
policer calls ocelot_vcap_policer_add() and ocelot_vcap_policer_del() to
set flow meter police.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stream gate settings for PSFP. Use SGI table to store
stream gate entries. Disable the gate entry when it is not used by any
stream.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.
For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vsc73xx_remove() returns zero unconditionally and no caller checks the
returned value. So convert the function to return no value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Model 88E6191X only supports >1G speeds on port 10. Port 0 and 9 are
only 1G.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211104171747.10509-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Normally it is expected that the dsa_device_ops :: rcv() method finishes
parsing the DSA tag and consumes it, then never looks at it again.
But commit c0bcf53766 ("net: dsa: ocelot: add hardware timestamping
support for Felix") added support for RX timestamping in a very
unconventional way. On this switch, a partial timestamp is available in
the DSA header, but the driver got away with not parsing that timestamp
right away, but instead delayed that parsing for a little longer:
dsa_switch_rcv():
nskb = cpu_dp->rcv(skb, dev); <------------- not here
-> ocelot_rcv()
...
skb = nskb;
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
...
if (dsa_skb_defer_rx_timestamp(p, skb)) <--- but here
-> felix_rxtstamp()
return 0;
When in felix_rxtstamp(), this driver accounted for the fact that
eth_type_trans() happened in the meanwhile, so it got a hold of the
extraction header again by subtracting (ETH_HLEN + OCELOT_TAG_LEN) bytes
from the current skb->data.
This worked for quite some time but was quite fragile from the very
beginning. Not to mention that having DSA tag parsing split in two
different files, under different folders (net/dsa/tag_ocelot.c vs
drivers/net/dsa/ocelot/felix.c) made it quite non-obvious for patches to
come that they might break this.
Finally, the blamed commit does the following: at the end of
ocelot_rcv(), it checks whether the skb payload contains a VLAN header.
If it does, and this port is under a VLAN-aware bridge, that VLAN ID
might not be correct in the sense that the packet might have suffered
VLAN rewriting due to TCAM rules (VCAP IS1). So we consume the VLAN ID
from the skb payload using __skb_vlan_pop(), and take the classified
VLAN ID from the DSA tag, and construct a hwaccel VLAN tag with the
classified VLAN, and the skb payload is VLAN-untagged.
The big problem is that __skb_vlan_pop() does:
memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);
__skb_pull(skb, VLAN_HLEN);
aka it moves the Ethernet header 4 bytes to the right, and pulls 4 bytes
from the skb headroom (effectively also moving skb->data, by definition).
So for felix_rxtstamp()'s fragile logic, all bets are off now.
Instead of having the "extraction" pointer point to the DSA header,
it actually points to 4 bytes _inside_ the extraction header.
Corollary, the last 4 bytes of the "extraction" header are in fact 4
stale bytes of the destination MAC address from the Ethernet header,
from prior to the __skb_vlan_pop() movement.
So of course, RX timestamps are completely bogus when the system is
configured in this way.
The fix is actually very simple: just don't structure the code like that.
For better or worse, the DSA PTP timestamping API does not offer a
straightforward way for drivers to present their RX timestamps, but
other drivers (sja1105) have established a simple mechanism to carry
their RX timestamp from dsa_device_ops :: rcv() all the way to
dsa_switch_ops :: port_rxtstamp() and even later. That mechanism is to
simply save the partial timestamp to the skb->cb, and complete it later.
Question: why don't we simply populate the skb's struct
skb_shared_hwtstamps from ocelot_rcv(), and bother with this
complication of propagating the timestamp to felix_rxtstamp()?
Answer: dsa_switch_ops :: port_rxtstamp() answers the question whether
PTP packets need sleepable context to retrieve the full RX timestamp.
Currently felix_rxtstamp() answers "no, thanks" to that question, and
calls ocelot_ptp_gettime64() from softirq atomic context. This is
understandable, since Felix VSC9959 is a PCIe memory-mapped switch, so
hardware access does not require sleeping. But the felix driver is
preparing for the introduction of other switches where hardware access
is over a slow bus like SPI or MDIO:
https://lore.kernel.org/lkml/20210814025003.2449143-1-colin.foster@in-advantage.com/
So I would like to keep this code structure, so the rework needed when
that driver will need PTP support will be minimal (answer "yes, I need
deferred context for this skb's RX timestamp", then the partial
timestamp will still be found in the skb->cb.
Fixes: ea440cd2d9 ("net: dsa: tag_ocelot: use VLAN information from tagging header when available")
Reported-by: Po Liu <po.liu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device set MAC06 exchange in the bootloader. This cause some
problem as we don't support this strange mode and we just set the port6
as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
instead of port0. Add an extra check and explicitly disable MAC06 exchange
to correctly configure the port PAD config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes: 3fcf734aa4 ("net: dsa: qca8k: add support for cpu port 6")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSWIP switch accesses various bridging layer tables (VLANs, FDBs,
forwarding rules) indirectly through PCE registers. These hardware
accesses are non-atomic, being comprised of several register reads and
writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE registers using
its own locking scheme. This patch adds that.
Note that the driver also uses the gswip_pce_load_microcode() function
to load a static configuration for the packet classification engine into
a table using the same registers. It is currently not protected, but
since that configuration is only done from the dsa_switch_ops :: setup
method, there is no risk of it being concurrent with other operations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 hardware seems as concurrent as can be, but when we create a
background script that adds/removes a rain of FDB entries without the
rtnl_mutex taken, then in parallel we do another operation like run
'bridge fdb show', we can notice these errors popping up:
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2
Luckily what is going on does not require a major rework in the driver.
The sja1105_dynamic_config_read() function sends multiple SPI buffers to
the peripheral until the operation completes. We should not do anything
until the hardware clears the VALID bit.
But since there is no locking (i.e. right now we are implicitly
serialized by the rtnl_mutex, but if we remove that), it might be
possible that the process which performs the dynamic config read is
preempted and another one performs a dynamic config write.
What will happen in that case is that sja1105_dynamic_config_read(),
when it resumes, expects to see VALIDENT set for the entry it reads
back. But it won't.
This can be corrected by introducing a mutex for serializing SPI
accesses to the dynamic config interface which should be atomic with
respect to each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at the code, the GSWIP switch appears to hold bridging service
structures (VLANs, FDBs, forwarding rules) in PCE table entries.
Hardware access to the PCE table is non-atomic, and is comprised of
several register reads and writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE table using its
own locking scheme. This patch adds that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 hardware seems as concurrent as can be, but when we create a
background script that adds/removes a rain of FDB entries without the
rtnl_mutex taken, then in parallel we do another operation like run
'bridge fdb show', we can notice these errors popping up:
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2
Luckily what is going on does not require a major rework in the driver.
The sja1105_dynamic_config_read() function sends multiple SPI buffers to
the peripheral until the operation completes. We should not do anything
until the hardware clears the VALID bit.
But since there is no locking (i.e. right now we are implicitly
serialized by the rtnl_mutex, but if we remove that), it might be
possible that the process which performs the dynamic config read is
preempted and another one performs a dynamic config write.
What will happen in that case is that sja1105_dynamic_config_read(),
when it resumes, expects to see VALIDENT set for the entry it reads
back. But it won't.
This can be corrected by introducing a mutex for serializing SPI
accesses to the dynamic config interface which should be atomic with
respect to each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following coccicheck warning:
./drivers/net/dsa/sja1105/sja1105_main.c:1193:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Fixes: 9ca482a246 ("net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delays")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211021094606.7118-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass a single argument to dsa_8021q_rx_vid and dsa_8021q_tx_vid that
contains the necessary information from the two arguments that are
currently provided: the switch and the port number.
Also rename those functions so that they have a dsa_port_* prefix, since
they operate on a struct dsa_port *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidy and organize qca8k setup function from multiple for loop.
Change for loop in bridge leave/join to scan all port and skip cpu port.
No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).
The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.
When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.
One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix delay settings applied to wrong cpu in parse_port_config. The delay
values is set to the wrong index as the cpu_port_index is incremented
too early. Start the cpu_port_index to -1 so the correct value is
applied to address also the case with invalid phy mode and not available
port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed based on a
GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found
in the OpenWrt source tree.
Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb
subdriver. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.
The RTL8365MB-VC switch is capable of offloading a large number of
features from the software, but this patch introduces only the most
basic DSA driver functionality. The ports always function as standalone
ports, with bridging handled in software.
One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.
Co-developed-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The NXP LS1028A switch has two Ethernet ports towards the CPU, but only
one of them is capable of acting as an NPI port at a time (inject and
extract packets using DSA tags).
However, using the alternative ocelot-8021q tagging protocol, it should
be possible to use both CPU ports symmetrically, but for that we need to
mark both ports in the device tree as DSA masters.
In the process of doing that, it can be seen that traffic to/from the
network stack gets broken, and this is because the Felix driver iterates
through all DSA CPU ports and configures them as NPI ports. But since
there can only be a single NPI port, we effectively end up in a
situation where DSA thinks the default CPU port is the first one, but
the hardware port configured to be an NPI is the last one.
I would like to treat this as a bug, because if the updated device trees
are going to start circulating, it would be really good for existing
kernels to support them, too.
Fixes: adb3dccf09 ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7 (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 6087175b79 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df4 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb7419198 ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d8 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d8 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eliminate the following coccicheck warning:
./drivers/net/dsa/rtl8366rb.c:1348:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for setting the STP state to the RTL8366RB
DSA switch. This rids the following message from the kernel on
e.g. OpenWrt:
DSA: failed to set STP state 3 (-95)
Since the RTL8366RB has one STP state register per FID with
two bit per port in each, we simply loop over all the FIDs
and set the state on all of them.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements fast aging per-port using the special "security"
register, which will flush any learned L2 LUT entries on a port.
The vendor API just enabled setting and clearing this bit, so
we set it to age out any entries on the port and then we clear
it again.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB hardware supports disabling learning per-port
so let's make use of this feature. Rename some unfortunately
named registers in the process.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a state variable to track whether a certain port
was VLAN filtering or not, but we can just inquire the DSA
core about this.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need a message for every VLAN association, dbg
is fine. The message about adding the DSA or CPU
port to a VLAN is directly misleading, this is perfectly
fine.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking that the MC (member config) was != 0
for some reason, all we need to check is that the config
has no ports, i.e. no members. Then it can be recycled.
This must be some misunderstanding.
Fixes: 4ddcaf1ebb ("net: dsa: rtl8366: Properly clear member config")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we were defining one VLAN per port for isolating the ports
the port_vlan_filtering() callback was implemented to enable a
VLAN on the port + 1. This function makes no sense, not only is
it incomplete as it only enables the VLAN, it doesn't do what
the callback is supposed to do, which is to selectively enable
and disable filtering on a certain port.
Implement the correct callback: we have two registers dealing
with filtering on the RTL9366RB, so we implement an ASIC-specific
callback and implement filering using the register bit that makes
the switch drop frames if the port is not in the VLAN member set.
The DSA documentation Documentation/networking/switchdev.rst states:
When the bridge has VLAN filtering enabled and a PVID is not
configured on the ingress port, untagged and 802.1p tagged
packets must be dropped. When the bridge has VLAN filtering
enabled and a PVID exists on the ingress port, untagged and
priority-tagged packets must be accepted and forwarded according
to the bridge's port membership of the PVID VLAN. When the
bridge has VLAN filtering disabled, the presence/lack of a
PVID should not influence the packet forwarding decision.
To comply with this, we add two arrays of bool in the RTL8366RB
state that keeps track of if filtering and PVID is enabled or
not for each port. We then add code such that whenever filtering
or PVID changes, we update the filter according to the
specification.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hacky default VLAN setup was done in order to direct
packets to the right ports and provide port isolation, both
which we now support properly using custom tags and proper
bridge port isolation.
We can drop the custom VLAN code and leave all VLAN handling
alone, as users expect things to be. We can also drop
ds->configure_vlan_while_not_filtering = false; and let
the core deal with any VLANs it wants.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use port isolation registers to configure bridge offloading.
Tested on the D-Link DIR-685, switching between ports and
sniffing ports to make sure no packets leak.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both forms are accepted, let's search for both when we
pre-validate the PHY modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
