This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing with the photometer shows that at least Raven Ridge DCN-1.0
does not achieve more than 10 bpc effective output precision with a
16 bpc unorm surface of type SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616,
unless linebuffer depth is increased from LB_PIXEL_DEPTH_30BPP to
LB_PIXEL_DEPTH_36BPP. Otherwise precision gets truncated somewhere
to 10 bpc effective depth.
Strangely this increase was not needed on Polaris11 DCE-11.2 during
testing to get 12 bpc effective precision. It also is not needed for
fp16 framebuffers.
Tested on DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the necessary format definition, bandwidth and pixel size mappings,
prescaler setup, and pixelformat selection, following the logic
already present for SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616.
The new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 is implemented as the
old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616 format, but with swapped
red <-> green color channel, by use of the hardware xbar.
Please note that on the DCN 1/2/3 display engines, the pixelformat
in hubp and dpp setup for the old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616
and the new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 was changed from
format id 22 to id 26. See amd/include/navi10_enum.h for the meaning
of the id's.
For format 22, the display engine read the framebuffer in 16 bpc format,
but truncated to the 12 bpc actually supported by later pipeline stages.
However, the engine took the 12 LSB of each color component for
truncation, which is incompatible with rendering at least under Vulkan,
where content is 16 bit wide, and a 12 MSB alignment would be appropriate,
if any. Format 20 for ARGB16161616_12MSB does work, but even better, we
can choose format 26 for ARGB16161616_UNORM, keeping all 16 bits around
until later stages of the display pipeline.
This allows to directly consume what the rendering hw produces under
Vulkan for swapchain format VK_FORMAT_R16G16B16A16_UNORM, as tested
with a patched version of the current AMD open-source amdvlk driver
which maps swapchain format VK_FORMAT_R16G16B16A16_UNORM onto
DRM_FORMAT_XBGR16161616.
The old id 22 would cause colorful pixeltrash to be displayed instead.
Tested under DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c:721:65-70: WARNING:
conversion to bool not needed here.
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c:1139:67-72: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HDR3DLUT and SHAPER memory blocks should be powered down when
they're not in use. This will reduce power consumption.
[How]
1. Write to HDR3DLUT_MEM_PWR_FORCE to put memory to shutdown
when HDR3DLUT is not used.
2. Write to SHAPER_MEM_PWR_FORCE to put memory to shutdown
when SHAPER is not used.
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The BLNDGAM memory blocks should be powered down when they're not in
use. This will reduce power consumption.
[How]
1. Write to BLNDGAM_MEM_PWR_FORCE to put memory to shutdown when BLNDGAM
is not used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
