This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing with the photometer shows that at least Raven Ridge DCN-1.0
does not achieve more than 10 bpc effective output precision with a
16 bpc unorm surface of type SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616,
unless linebuffer depth is increased from LB_PIXEL_DEPTH_30BPP to
LB_PIXEL_DEPTH_36BPP. Otherwise precision gets truncated somewhere
to 10 bpc effective depth.
Strangely this increase was not needed on Polaris11 DCE-11.2 during
testing to get 12 bpc effective precision. It also is not needed for
fp16 framebuffers.
Tested on DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the necessary format definition, bandwidth and pixel size mappings,
prescaler setup, and pixelformat selection, following the logic
already present for SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616.
The new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 is implemented as the
old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616 format, but with swapped
red <-> green color channel, by use of the hardware xbar.
Please note that on the DCN 1/2/3 display engines, the pixelformat
in hubp and dpp setup for the old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616
and the new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 was changed from
format id 22 to id 26. See amd/include/navi10_enum.h for the meaning
of the id's.
For format 22, the display engine read the framebuffer in 16 bpc format,
but truncated to the 12 bpc actually supported by later pipeline stages.
However, the engine took the 12 LSB of each color component for
truncation, which is incompatible with rendering at least under Vulkan,
where content is 16 bit wide, and a 12 MSB alignment would be appropriate,
if any. Format 20 for ARGB16161616_12MSB does work, but even better, we
can choose format 26 for ARGB16161616_UNORM, keeping all 16 bits around
until later stages of the display pipeline.
This allows to directly consume what the rendering hw produces under
Vulkan for swapchain format VK_FORMAT_R16G16B16A16_UNORM, as tested
with a patched version of the current AMD open-source amdvlk driver
which maps swapchain format VK_FORMAT_R16G16B16A16_UNORM onto
DRM_FORMAT_XBGR16161616.
The old id 22 would cause colorful pixeltrash to be displayed instead.
Tested under DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for following new format, no alpha
SURFACE_PIXEL_FORMAT_GRPH_RGB111110_FLOAT/_FIX:
SURFACE_PIXEL_FORMAT_GRPH_BGR101111_FLOAT/_FIX
same as case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dpp2_get_optimal_number_of_taps function is never used. Removing
just for code cleaning up.
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.
[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dpp2_get_optimal_number_of_taps is incorrect, and dcn2 should be using
dpp1_get_optimal_number_of_taps instead
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c: In function dpp2_get_optimal_number_of_taps:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c:359:11: warning: variable pixel_width set but not used [-Wunused-but-set-variable]
It is not used since commit f7de96ee8b ("drm/amd/display:
Add DCN2 DPP")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OGAM_MEM_PWR could stay in light up when driver woke up to update gamma.
either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away.
Easy reproduce after LOW_MEM Power feature enables and resume from S3.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'Divide by zero' error happens when line size happens to be zero.
[how]
The code that makes sure line size minimum value can be 1 was already
present in DCN1 part of the driver, this is mearly a port to DCN2.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
