The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
In commit 9b7f76dc37919ea36caa9680a3f765e5b19b25fb,
Author: Lars Ellenberg <lars.ellenberg@linbit.com>
Date: Wed Aug 11 23:40:24 2010 +0200
drbd: new configuration parameter c-min-rate
a bad chunk slipped through, which is now reverted as well,
restoring the correct irqsave for the endio callback.
This patch also add comments at both req_mod()
and in the endio callback so it should not happen again.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should fix a performance degradation we observed recently.
If we don't expect any subheader, we should not call into the tcp stack,
as that may add considerable latency if there is no data available at
this point.
For a synthetic synchronous write load with single outstanding writes,
this additional latency when processing the "unplug remote" packet
added up to a performance degradation factor >= 10.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix build for PROC_FS disabled
block: fix amiga and atari floppy driver compile warning
blk-throttle: Fix calculation of max number of WRITES to be dispatched
ioprio: grab rcu_read_lock in sys_ioprio_{set,get}()
xen/blkfront: cope with backend that fail empty BLKIF_OP_WRITE_BARRIER requests
xen/blkfront: Implement FUA with BLKIF_OP_WRITE_BARRIER
xen/blkfront: change blk_shadow.request to proper pointer
xen/blkfront: map REQ_FLUSH into a full barrier
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent patch to fix the removal of a non-existing proc
directory introduced this build problem for !CONFIG_PROC_FS:
drivers/block/cciss.c:4929: error: 'proc_cciss' undeclared (first use in this function)
Fix it by moving proc_cciss outside of the CONFIG_PROC_FS scope.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert, my crosstool don't produce warning below. I guess this has to do
something with compiler version.
- Geert noticed following warning during compilation.
drivers/block/amiflop.c:1344: warning: ‘rq’ may be used uninitialized in
this function
drivers/block/ataflop.c:1402: warning: ‘rq’ may be used uninitialized in
this function
- Initialize rq to NULL to fix the warning. If we can't find a suitable request
to dispatch, this function should return NULL instead of a possibly garbage
pointer.
- Cross compile tested only. Don't have hardware to test it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After recent blkdev_get() modifications, open_by_devnum() and
open_bdev_exclusive() are simple wrappers around blkdev_get().
Replace them with blkdev_get_by_dev() and blkdev_get_by_path().
blkdev_get_by_dev() is identical to open_by_devnum().
blkdev_get_by_path() is slightly different in that it doesn't
automatically add %FMODE_EXCL to @mode.
All users are converted. Most conversions are mechanical and don't
introduce any behavior difference. There are several exceptions.
* btrfs now sets FMODE_EXCL in btrfs_device->mode, so there's no
reason to OR it explicitly on blkdev_put().
* gfs2, nilfs2 and the generic mount_bdev() now set FMODE_EXCL in
sb->s_mode.
* With the above changes, sb->s_mode now always should contain
FMODE_EXCL. WARN_ON_ONCE() added to kill_block_super() to detect
errors.
The new blkdev_get_*() functions are with proper docbook comments.
While at it, add function description to blkdev_get() too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Joern Engel <joern@lazybastard.org>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: reiserfs-devel@vger.kernel.org
Cc: xfs-masters@oss.sgi.com
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.
* blkdev_get/put() are the primary open and close functions.
* bd_claim/release() deal with exclusive open.
* open/close_bdev_exclusive() are combination of open and claim and
the other way around, respectively.
* bd_link/unlink_disk_holder() to create and remove holder/slave
symlinks.
* open_by_devnum() wraps bdget() + blkdev_get().
The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access. Reorganize the interface such that,
* blkdev_get() is extended to include exclusive access management.
@holder argument is added and, if is @FMODE_EXCL specified, it will
gain exclusive access atomically w.r.t. other exclusive accesses.
* blkdev_put() is similarly extended. It now takes @mode argument and
if @FMODE_EXCL is set, it releases an exclusive access. Also, when
the last exclusive claim is released, the holder/slave symlinks are
removed automatically.
* bd_claim/release() and close_bdev_exclusive() are no longer
necessary and either made static or removed.
* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
is no longer necessary and removed.
* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
and blkdev_get(). It also has an unexpected extra bdev_read_only()
test which probably should be moved into blkdev_get().
* open_by_devnum() is modified to take @holder argument and pass it to
blkdev_get().
Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should). This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.
open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features. Well, let's leave them for another day.
Most conversions are straight-forward. drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
block: remove unused copy_io_context()
Documentation: remove anticipatory scheduler info
block: remove REQ_HARDBARRIER
ioprio: rcu_read_lock/unlock protect find_task_by_vpid call (V2)
ioprio: fix RCU locking around task dereference
block: ioctl: fix information leak to userland
block: read i_size with i_size_read()
cciss: fix proc warning on attempt to remove non-existant directory
bio: take care not overflow page count when mapping/copying user data
block: limit vec count in bio_kmalloc() and bio_alloc_map_data()
block: take care not to overflow when calculating total iov length
block: check for proper length of iov entries in blk_rq_map_user_iov()
cciss: remove controllers supported by hpsa
cciss: use usleep_range not msleep for small sleeps
cciss: limit commands allocated on reset_devices
cciss: Use kernel provided PCI state save and restore functions
cciss: fix board status waiting code
drbd: Removed checks for REQ_HARDBARRIER on incomming BIOs
drbd: REQ_HARDBARRIER -> REQ_FUA transition for meta data accesses
drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code
...
REQ_HARDBARRIER is dead now, so remove the leftovers. What's left
at this point is:
- various checks inside the block layer.
- sanity checks in bio based drivers.
- now unused bio_empty_barrier helper.
- Xen blockfront use of BLKIF_OP_WRITE_BARRIER - it's dead for a while,
but Xen really needs to sort out it's barrier situaton.
- setting of ordered tags in uas - dead code copied from old scsi
drivers.
- scsi different retry for barriers - it's dead and should have been
removed when flushes were converted to FS requests.
- blktrace handling of barriers - removed. Someone who knows blktrace
better should add support for REQ_FLUSH and REQ_FUA, though.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Convert direct reads of an inode's i_size to using i_size_read().
i_size_{read,write} use a seqcount to protect reads from accessing
incomple writes. Concurrent i_size_write()s require mutual exclussion
to protect the seqcount that is used by i_size_{read,write}. But
i_size_read() callers do not need to use additional locking.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)
Convert aoecmd_cfg_pkts() to RCU locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the NO_GEOM macro with a proper static inline function and
converts an open-coded caller in check_floppy_change() to use it.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
While scanning the floopy code due to c093ee4f07 ("floppy: fix
use-after-free in module load failure path"), I found one more instance
of trying to access disk->queue pointer after doing put_disk() on
gendisk. For some reason , floppy moule still loads/unloads fine. The
object is probably still around with right pointer values.
o There seems to be one more instance of trying to cleanup the request
queue after we have called put_disk() on associated gendisk.
o This fix is more out of code inspection. Even without this fix for
some reason I am able to load/unload floppy module without any
issues.
o Floppy module loads/unloads fine after the fix.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 488211844e ("floppy: switch to one queue per drive instead of
sharing a queue") introduced a use-after-free. We do "put_disk()" on
the disk device _before_ we then clean up the queue associated with that
disk.
Move the put_disk() down to avoid dereferencing a free'd data structure.
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some(?) Xen block backends fail BLKIF_OP_WRITE_BARRIER requests, which
Linux uses as a cache flush operation. In that case, disable use
of FLUSH.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
The BLKIF_OP_WRITE_BARRIER is a full ordered barrier, so we can use it
to implement FUA as well as a plain FLUSH.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Implement a flush as a full barrier, since we have nothing weaker.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Christoph Hellwig <hch@lst.de>
and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: register xen pci notifier
xen: initialize cpu masks for pv guests in xen_smp_init
xen: add a missing #include to arch/x86/pci/xen.c
xen: mask the MTRR feature from the cpuid
xen: make hvc_xen console work for dom0.
xen: add the direct mapping area for ISA bus access
xen: Initialize xenbus for dom0.
xen: use vcpu_ops to setup cpu masks
xen: map a dummy page for local apic and ioapic in xen_set_fixmap
xen: remap MSIs into pirqs when running as initial domain
xen: remap GSIs as pirqs when running as initial domain
xen: introduce XEN_DOM0 as a silent option
xen: map MSIs into pirqs
xen: support GSI -> pirq remapping in PV on HVM guests
xen: add xen hvm acpi_register_gsi variant
acpi: use indirect call to register gsi in different modes
xen: implement xen_hvm_register_pirq
xen: get the maximum number of pirqs from xen
xen: support pirq != irq
* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
X86/PCI: Remove the dependency on isapnp_disable.
xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
x86: xen: Sanitse irq handling (part two)
swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
xen/pci: Request ACS when Xen-SWIOTLB is activated.
xen-pcifront: Xen PCI frontend driver.
xenbus: prevent warnings on unhandled enumeration values
xenbus: Xen paravirtualised PCI hotplug support.
xen/x86/PCI: Add support for the Xen PCI subsystem
x86: Introduce x86_msi_ops
msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
x86/PCI: Export pci_walk_bus function.
x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
x86/PCI: Clean up pci_cache_line_size
xen: fix shared irq device passthrough
xen: Provide a variant of xen_poll_irq with timeout.
xen: Find an unbound irq number in reverse order (high to low).
xen: statically initialize cpu_evtchn_mask_p
...
Fix up trivial conflicts in drivers/pci/Makefile
This patch removes the controller overlap between cciss and hpsa. It was
decided that no overlap should exist. All new controllers will use the hpsa
SCSI based driver.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Structure IOCTL_Command_struct is copied to userland with
some padding fields at the end of the struct unitialized.
It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As described in https://bugzilla.kernel.org/show_bug.cgi?id=19922
: I had an AoE device go down overnight, and while a server was trying to
: write to it, it was also writing this message to its logs:
:
: 209 printk(KERN_INFO "aoe: device %ld.%d is not up\n",
: 210 d->aoemajor, d->aoeminor);
:
: The message appeared many times per second, and over several hours
: produced about 7.5 gigabytes of log files, filling up all free space on
: the root filesystem.
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Suggested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If CONFIG_LBDAF=y, `sector_t' becomes `u64' instead of `unsigned long':
drivers/block/z2ram.c: In function ¡do_z2_request¢:
drivers/block/z2ram.c:83: warning: format %lu expects type `long unsigned int', but argument 2 has type `sector_t'
Hence always cast it to `unsigned long long' for printing. Also do the
pr_err() dance, while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly cancel aoedev->work on free instead of depending on
flush_scheduled_works().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Failure to create drbd_ee_mempool appears not to get checked. Looks like
a copy-and-paste problem to me.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In autoclear mode bdev is NULL but the sysfs
entry should be destroyed otherwise this warning appears:
WARNING: at fs/sysfs/dir.c:451 sysfs_add_one+0x82/0x95()
sysfs: cannot create duplicate filename '/devices/virtual/block/loop0/loop'
Fixes commit ee86273062
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Ensure kmap_atomic() usage is strictly nested
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
We would prefer not to have any overlap between the two drivers.
Remove the cciss_allow_hpsa option, as it it is no longer needed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
xen-blkfront: disable barrier/flush write support
Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
block: remove BLKDEV_IFL_WAIT
aic7xxx_old: removed unused 'req' variable
block: remove the BH_Eopnotsupp flag
block: remove the BLKDEV_IFL_BARRIER flag
block: remove the WRITE_BARRIER flag
swap: do not send discards as barriers
fat: do not send discards as barriers
ext4: do not send discards as barriers
jbd2: replace barriers with explicit flush / FUA usage
jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
jbd: replace barriers with explicit flush / FUA usage
nilfs2: replace barriers with explicit flush / FUA usage
reiserfs: replace barriers with explicit flush / FUA usage
gfs2: replace barriers with explicit flush / FUA usage
btrfs: replace barriers with explicit flush / FUA usage
xfs: replace barriers with explicit flush / FUA usage
block: pass gfp_mask and flags to sb_issue_discard
dm: convey that all flushes are processed as empty
...
* 'for-2.6.37/drivers' of git://git.kernel.dk/linux-2.6-block: (95 commits)
cciss: fix PCI IDs for new Smart Array controllers
drbd: add race-breaker to drbd_go_diskless
drbd: use dynamic_dev_dbg to optionally log uuid changes
dynamic_debug.h: Fix dynamic_dev_dbg() macro if CONFIG_DYNAMIC_DEBUG not set
drbd: cleanup: change "<= 0" to "== 0"
drbd: relax the grace period of the md_sync timer again
drbd: add some more explicit drbd_md_sync
drbd: drop wrong debug asserts, fix recently introduced race
drbd: cleanup useless leftover warn/error printk's
drbd: add explicit drbd_md_sync to drbd_resync_finished
drbd: Do not log an ASSERT for P_OV_REQUEST packets while C_CONNECTED
drbd: fix for possible deadlock on IO error during resync
drbd: fix unlikely access after free and list corruption
drbd: fix for spurious fullsync (uuids rotated too fast)
drbd: allow for explicit resync-finished notifications
drbd: preparation commit, using full state in receive_state()
drbd: drbd_send_ack_dp must not rely on header information
drbd: Fix regression in recv_bm_rle_bits (compressed bitmap)
drbd: Fixed a stupid copy and paste error
drbd: Allow larger values for c-fill-target.
...
Fix up trivial conflict in drivers/block/ataflop.c due to BKL removal
* 'for-2.6.37/core' of git://git.kernel.dk/linux-2.6-block: (39 commits)
cfq-iosched: Fix a gcc 4.5 warning and put some comments
block: Turn bvec_k{un,}map_irq() into static inline functions
block: fix accounting bug on cross partition merges
block: Make the integrity mapped property a bio flag
block: Fix double free in blk_integrity_unregister
block: Ensure physical block size is unsigned int
blkio-throttle: Fix possible multiplication overflow in iops calculations
blkio-throttle: limit max iops value to UINT_MAX
blkio-throttle: There is no need to convert jiffies to milli seconds
blkio-throttle: Fix link failure failure on i386
blkio: Recalculate the throttled bio dispatch time upon throttle limit change
blkio: Add root group to td->tg_list
blkio: deletion of a cgroup was causes oops
blkio: Do not export throttle files if CONFIG_BLK_DEV_THROTTLING=n
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: revert bad fix for memory hotplug causing bounces
Fix compile error in blk-exec.c for !CONFIG_DETECT_HUNG_TASK
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: Prevent hang_check firing during long I/O
cfq: improve fsync performance for small files
...
Fix up trivial conflicts due to __rcu sparse annotation in include/linux/genhd.h
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
This commit changes prefix for some of the USB mass storage
class related macros (ie. USB_SC_ for subclass and USB_PR_
for class).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That assertion's condition needed adjustment for today's semantics
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we don't rate limit it, and you happen to log err level messages via
serial console, an IO error on a disconnected Primary may cause serious
unresponsiveness.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This codepath used to be called only for failed kmalloc GFP_ATOMIC,
but is now also triggered by other things.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we get an IO-error during an activity log transaction,
if we failed to write the bitmap of the evicted extent,
we must not write the transaction itself.
If we failed to write the transaction,
we must not even submit the corresponding bio,
as its extent is not yet marked in the activity log.
Otherwise, if this was a disconneted Primary (degraded cluster), which
now lost its disk as well, and we later re-attach the same backend
storage, we possibly "forget" to resync some parts of the disk that
potentially have been changed.
On the receiving side, when receiving from a peer with unhealthy disk,
checking for pdsk == D_DISKLESS is not enough, we need to set out of
sync and do AL transactions for everything pdsk < D_INCONSISTENT on the
receiving side.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we have contention in drbd_al_begin_iod (heavy randon IO),
an administrative request to detach the disk may deadlock
for similar reasons as the recently fixed deadlock if detaching
because of IO-error.
The approach taken here is to either go through the intermediate
cleanup state D_FAILED, or first lock out application io,
don't just go directly to D_DISKLESS.
We need an additional state bit (WAS_IO_ERROR) to distinguish
the -> D_FAILED because of IO-error from other failures.
Sanitize D_ATTACHING -> D_FAILED to D_ATTACHING -> D_DISKLESS.
If only attaching, ldev may be missing still, but would be referenced
from within the after_state_ch for -> D_FAILED, potentially
dereferencing a NULL pointer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If those messages ever get logged, clearly state that they are
actually failed ASSERTS, so our regression tests can pick them up
from the logs more easily.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Every code path changing the current UUID needs to get it on stable
storage anyways. Flush it to disk right there, remove the now obsolte
explicit drbd_md_sync statements in the other code paths.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio_blk: remove BKL leftovers
virtio: console: Disable lseek(2) for port file operations
virtio: console: Send SIGIO in case of port unplug
virtio: console: Send SIGIO on new data arrival on ports
virtio: console: Send SIGIO to processes that request it for host events
virtio: console: Reference counting portdev structs is not needed
virtio: console: Add reference counting for port struct
virtio: console: Use cdev_alloc() instead of cdev_init()
virtio: console: Add a find_port_by_devt() function
virtio: console: Add a list of portdevs that are active
virtio: console: open: Use a common path for error handling
virtio: console: remove_port() should return void
virtio: console: Make write() return -ENODEV on hot-unplug
virtio: console: Make read() return -ENODEV on hot-unplug
virtio: console: Unblock poll on port hot-unplug
virtio: console: Un-block reads on chardev close
virtio: console: Check if portdev is valid in send_control_msg()
virtio: console: Remove control vq data only if using multiport support
virtio: console: Reset vdev before removing device
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (22 commits)
ceph: do not carry i_lock for readdir from dcache
fs/ceph/xattr.c: Use kmemdup
rbd: passing wrong variable to bvec_kunmap_irq()
rbd: null vs ERR_PTR
ceph: fix num_pages_free accounting in pagelist
ceph: add CEPH_MDS_OP_SETDIRLAYOUT and associated ioctl.
ceph: don't crash when passed bad mount options
ceph: fix debugfs warnings
block: rbd: removing unnecessary test
block: rbd: fixed may leaks
ceph: switch from BKL to lock_flocks()
ceph: preallocate flock state without locks held
ceph: add pagelist_reserve, pagelist_truncate, pagelist_set_cursor
ceph: use mapping->nrpages to determine if mapping is empty
ceph: only invalidate on check_caps if we actually have pages
ceph: do not hide .snap in root directory
rbd: introduce rados block device (rbd), based on libceph
ceph: factor out libceph from Ceph file system
ceph-rbd: osdc support for osd call and rollback operations
ceph: messenger and osdc changes for rbd
...
Remove the BKL usage added in "block: push down BKL into .locked_ioctl".
Virtio-blk doesn't use the BKL for anything, and doesn't implement any
ioctl command by itself, but only uses the generic scsi_cmd_ioctl
which is fine without the BKL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We should be passing "buf" here insead of "bv". This is tricky because
it's not the same as kmap() and kunmap(). GCC does warn about it if you
compile on i386 with CONFIG_HIGHMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
ceph_alloc_page_vector() returns ERR_PTR(-ENOMEM) on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
rbd_client_create() doesn't free rbdc, this leads to many leaks.
seg_len in rbd_do_op() is unsigned, so (seg_len < 0) makes no sense.
Also if fixed check fails then seg_name is leaked.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
The rados block device (rbd), based on osdblk, creates a block device
that is backed by objects stored in the Ceph distributed object storage
cluster. Each device consists of a single metadata object and data
striped over many data objects.
The rbd driver supports read-only snapshots.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
cciss: fix PCI IDs for new controllers
This patch fixes the botched up PCI IDs of new controllers. Please consider
this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Convert big-endian DTB to little-endian if necessary.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
XenbusStateReconfiguring/XenbusStateReconfigured were introduced by
c/s 437, but aren't handled in many switch statements.
.. also pulled from the linux-2.6-sparse-tree tree.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This adds a necessary race breaker to these commits:
drbd: fix for possible deadlock on IO error during resync
drbd: drop wrong debug asserts, fix recently introduced race
What we do is get a refcount, check the state, then depending on the
state and the requested minimum disk state, either hold it (success),
or give it back immediately (failed "try lock").
Some code paths (flushing of drbd metadata) may still grab and hold a
refcount even if we are D_FAILED (application IO won't).
So even if we hit local_cnt == 0 once after being D_FAILED,
we still need to wait for that again after we changed to D_DISKLESS.
Once local_cnt reaches 0 while we are D_DISKLESS, we can be sure that
no one will look at the protected members anymore, so only then is it
safe to free them.
We cannot easily convert to standard locking primitives here, as we want
to be able to use it in atomic context (we always do a "try lock"),
as well as hold references for a "long time" (from IO submission to
completion callback).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
dt is unsigned so it's never less than zero. We are calculating the
elapsed time, and that's never less than zero (unless there is a bug or
we invent time travel). The comparison here is just to guard against
divide by zero bugs.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Consolidate the ifdef's for the debug level, accidentally the used both
DEBUG and DRBD_DEBUG_MD_SYNC. Default to off.
For production, we can safely reduce the grace period for this timer
again the the value we used to have.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It sometimes may take a while for the after state change work to be
scheduled, which does drbd_md_sync. At convenient places, we should do
explicit drbd_md_sync to have the new state information on disk as soon
as possible.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
commit 2372c38caadeaebc68a5ee190782c2a0df01edc3
drbd: fix for possible deadlock on IO error during resync
introduced a new ASSERT, which turns out to be wrong. Drop it.
Also serialize the state change to D_DISKLESS with the after state
change work of the -> D_FAILED transition, don't open a new race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As we usually update the generation UUIDs here, we should explicitly
sync them to disk. So far this has been done only implicitly by related
code paths.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This might happen if on the VERIFY_S node the disk gets dropped.
Although this is an cluster wide state transition, the VERIFY_T node,
updates it connection state first. Then the ack packet for the
cluster wide state transition travels back, and the VERIFY_S node
stops to produce the P_OV_REQUEST packets.
There is absolutely nothing wrong with that.
Further, do not log "Can not satisfy peer's..." on the VERIFY_S
node in this case, but pretend that they had equal checksum.
[Bugz 327]
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Scenario:
Something (say, flush-147:0) is in drbd_al_begin_io,
holding a local_cnt, waiting for the resync to make progress.
Disk fails, worker in after_state_ch does drbd_rs_cancel_all,
then waits for local_cnt to drop to zero.
flush-147:0 is woken by drbd_rs_cancel_all, needs to write an AL
transaction, and queues that on the worker.
Deadlock.
Fix: do not wait in the worker, have put_ldev() trigger the
state change D_FAILED -> D_DISKLESS when necessary.
put_ldev() cannot do the state change directly, as it may or may not
already hold various spinlocks. We queue a short work instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Various cleanup paths have been incomplete, for the very unlikely case
that we cannot allocate enough bios from process context when submitting
on behalf of the peer or resync process.
Never observed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If it was an "empty" resync, the SyncSource may have already "finished"
the resync and rotated the UUIDs, before noticing the connection loss
(and generating a new uuid, if Primary, rotating again), while the
SyncTarget did not change its uuids at all, or only got to the previous
sync-uuid.
This would then again lead to a full sync on next handshake
(see also Bug #251).
Fix:
Use explicit resync finished notification even for empty resyncs,
do not finish an empty resync implicitly on the SyncSource.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Preparation patch so more drbd_send_state() usage on the peer
will not confuse drbd in receive_state().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
no functional change, just using full state instead of just the .conn
part of it for comparisons.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
introduced a new on-the-wire packet header format. We must no longer
assume either format, but use the result of whatever drbd_recv_header
has decoded.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to be16_to_cpu the length field in our received packet header.
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
changed this, but forgot to adjust a few places where we relied on
h->length being in native byte order.
This broke the receiving side of the RLE compressed bitmap exchange.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This caused rs_planed to be not in sync with the content of the fifo.
That in turn could cause that the resync comes to a complete halt.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Connections through a compressing proxy might have more bits
on the fly. 500MByte instead of 50MByte
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we release the page pointed to by md_io_tmpp, we need to zero out the
pointer, too, as that may be used later to decide whether we need to
allocate a new page again.
Impact: a previously freed page may be used and clobbered. Depending on
what that particular page is being used for meanwhile, this may result
in silent data corruption of completely unrelated things.
Only of concern on devices with logical_block_size != 512 byte,
if you re-attach after becoming diskless once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Two missing corner cases to the "maximum packet size" handshake.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There are three ways to get IO suspended:
* Loss of any access to data
* Fence-peer-handler running
* User requested to suspend IO
Track those in different bits, so that one condition clearing its
state bit does not interfere with the other two conditions.
Only when the user resumes IO he overrules all three bits.
The fact is hidden from the user, he sees only a single suspend
bit.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Forgot to consider the max size for the resync requests.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a synctarget lost connection while being WFSyncUUID,
due to "state sanitizing", the attempted state change to SyncTarget
looked like an "invalidate" to after_state_ch() later,
thus caused a full sync on next handshake (Bug #318).
drbd0: PingAck did not arrive in time.
drbd0: peer( Primary -> Unknown ) conn( WFSyncUUID -> NetworkFailure ) pdsk( UpToDate -> DUnknown )
from : { cs:NetworkFailure ro:Secondary/Unknown ds:UpToDate/DUnknown r--- }
to : { cs:SyncTarget ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
after sanizising, resulted in
state: { cs:NetworkFailure ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
drbd0: disk( UpToDate -> Inconsistent )
Fix:
don't mask state transition errors in "sanitizing",
so the requested state change to SyncTarget fails,
instead of being implicitly "remaped" to invalidate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we cannot satisfy a request (because our disk just broke),
we still need to drain the payload. Or we'll get a protocol error
when interpreting the payload as DRBD packet header.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG trace would look like:
lc_find
drbd_rs_complete_io
got_OVResult
drbd_asender
Could be triggered by explicit, or IO-error policy based,
detach during online-verify.
We may only dereference mdev->resync, if we first get_ldev(), as the
disk may break any time, causing mdev->resync to disappear once all
ldev references have been returned.
Already in flight online-verify requests or replies may still come in,
which we then need to ignore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just in case we have some pending meta data changes to sync, do it
before we call our userland helper, as that may take some time,
or even cause a hard reboot.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
addendum to baa33ae4eaa4477b60af7c434c0ddd1d182c1ae7
The race:
drbd_md_sync()
if (!test_and_clear_bit(MD_DIRTY, &mdev->flags))
return;
==> RACE with drbd_md_mark_dirty() rearming the timer.
del_timer(&mdev->md_sync_timer);
Fixed by moving the del_timer before the test_and_clear_bit.
Additionally only rearm the timer in drbd_md_mark_dirty, if MD_DIRTY was
not already set, reduce the grace period from five to one second, and
add an ifdef'ed debuging aid to find code paths missing an explicit
drbd_md_sync, if any, as those are the only relevant ones for this race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The actual race happened int the drbd_start_resync() function. Where
drbd_resync_finished() -> __drbd_set_state() set STOP_SYNC_TIMER and
armed the timer.
If the timer fired before execution reaches the mod_timer statement
at the end of drbd_start_resync() the latter would cause an
unexpected call to w_make_resync_request().
Removed the STOP_SYNC_TIMER bit, and base it on the connection state.
The STOP_SYNC_TIMER bit probably originates probably the time before
the state engine.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If pacemaker (for example) decided to initialize minor devices not in
the exact sync-after dependency order, the configuration partially
failed with an error "The sync-after minor number is invalid". (Bugz. #322)
We can avoid that by implicitly creating unconfigured minor devices,
if others depend on them.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a drbd_nl_net_conf hits the small window between the state change
to C_STANDALONE and the corresponding cleanup in after_state_ch,
that cleanup would throw away stuff we now need again,
and later trigger BUG_ON()s.
Fixed by properly serializing the new config request with
any pending cleanup.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the complete device is marked as out of sync, we can disable
updates of the on disk AL. Currently AL updates are only disabled
if one uses the "invalidate-remote" command on an unconnected,
primary device, or when at attach time all bits in the bitmap are
set.
As of now, AL updated do not get disabled when a all bits becomes
set due to application writes to an unconnected DRBD device.
While this is a missing feature, it is not considered important,
and might get added later.
BTW, after initializing a "one legged" DRBD device
drbdadm create-md resX
drbdadm -- --force primary resX
AL updates also get disabled, until the first connect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now we have multiple BIOs per ee, packets with a 32 bit length field,
it gets time to use these goodies.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we intent to use the block_id member of an epoch entry,
we may not use the digest member.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We now track the data rate of locally submitted resync related requests,
and can thus detect non-resync activity on the lower level device.
If the current sync rate is above c-min-rate, and the lower level device
appears to be busy, we throttle the resyncer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
also canonicalize the return values of read_for_csum
and drbd_rs_begin_io to return -ESOMETHING, or 0 for success.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The current resync speed as displayed in /proc/drbd fluctuates a lot.
Using an array of rolling marks makes this calculation much more stable.
We used to have this (a long time ago with 0.7), but it got lost somehow.
If "stalled", do not discard the rest of the information, just add a
" (stalled)" tag to the progress line.
This patch also shortens a spinlock critical section somewhat, and
reduces the number of atomic operations in put_ldev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The commit 288f422ec1
drbd: Track all IO requests on the TL, not writes only
moved a list_add_tail(req, ) into a region where req
may have just been freed due to conflict detection.
Fix this by adding a proper cleanup section for that code path.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We may not free tl_hash when IO is suspended, since we can not wait
until ap_bio_cnt reaches zero.
We can do this after susp reched 0, since then tl_clear was called
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
After disconnect (most likely mdev->net_cnt == 0) and we are
still in an unstable state (!drbd_state_is_stable()). When we
get an IO request in drbd_get_max_buffers() (called from
__inc_ap_bio_cond(), called from inc_ap_bio()) we wake up
misc_wait. Misc_wait is also used in inc_ap_bio() to sleep
until the outcome of __inc_ap_bio_cond() changes. => Busy loop!
Solution: Have a dedicated wait queue for get_net_conf() and
put_net_conf().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make sure the state engine can deny two primaries to connect
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When a fencing policy of "resource-and-stonith" is configured,
and DRBD looses connection to it's peer, we can delay the
creation of a new current-UUID until IO gets thawed.
That allows one to deploy fence-peer handlers that actually
commit suicide on the machine they get started.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since we can not thaw the transfer log, the next logical step is
to allow reconnects while the fence-peer handler runs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
State transitions in the space of non-allowed states used
to be very noisy. Reduce that, since that has little value
for the majority of the user base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When no data is accessible (no connection to the peer, nor a local disk)
allow the user to select to freeze all IO operations instead of getting
IO errors.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If IO was frozen for a temporal network outage, resend the
content of the transfer-log into the newly established connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With that the drbd_fail_pending_reads() function becomes obsolete.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should pass "buf" to bvec_kunmap_irq() instead of "bv". The api is
like kmap_atomic() instead of kmap().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Must drop reference taken by blk_make_request().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .35.x
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PKT_CTRL_CMD_STATUS device ioctl retrieves a pointer to a
pktcdvd_device from the global pkt_devs array. The index into this
array is provided directly by the user and is a signed integer, so the
comparison to ensure that it falls within the bounds of this array will
fail when provided with a negative index.
This can be used to read arbitrary kernel memory or cause a crash due to
an invalid pointer dereference. This can be exploited by users with
permission to open /dev/pktcdvd/control (on many distributions, this is
readable by group "cdrom").
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
[ Rather than add a cast, just make the function take the right type -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o Use one request queue per gendisk instead of sharing the queue.
o Don't have hardware. No compile testing or run time testing done. Completely
untested.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
o Use one request queue per gendisk instead of sharing request queue
o Don't have hardware. No compile testing or run time testing done. Completely
untested.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Pretty straight forward conversion. Note that we do round-robin
between the drives that have available requests, before we simply
used the drive that the IO scheduler told us to. Since the IO
scheduler doesn't care about multiple devices per queue, the resulting
sort would not have made sense.
Fixed by Vivek to get rid of a double lock problem in set_next_request()
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
The "h->scatter_list" is allocated inside a for loop. If any of those
allocations fail, then the rest of the list is uninitialized data. When
we free it we should start from the top and free backwards so that we
don't call kfree() on uninitialized pointers.
Also if the allocation for "h->scatter_list" fails then we would get an
Oops here. I should have noticed this when I send: 4ee69851c "cciss:
handle allocation failure." but I didn't. Sorry about that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
All the blkdev_issue_* helpers can only sanely be used for synchronous
caller. To issue cache flushes or barriers asynchronously the caller needs
to set up a bio by itself with a completion callback to move the asynchronous
state machine ahead. So drop the BLKDEV_IFL_WAIT flag that is always
specified when calling blkdev_issue_* and also remove the now unused flags
argument to blkdev_issue_flush and blkdev_issue_zeroout. For
blkdev_issue_discard we need to keep it for the secure discard flag, which
gains a more descriptive name and loses the bitops vs flag confusion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have several users of min_not_zero, each of them using their own
definition. Move the define to kernel.h.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
Remove now unused REQ_HARDBARRIER support. virtio_blk already
supports REQ_FLUSH and the usefulness of REQ_FUA for virtio_blk is
questionable at this point, so there's nothing else to do to support
new REQ_FLUSH/FUA interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Deprecate REQ_HARDBARRIER and implement REQ_FLUSH/FUA instead. Also,
instead of checking file->f_op->fsync() directly, look at the value of
vfs_fsync() and ignore -EINVAL return.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests. Deprecate barrier. All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().
blk_queue_flush() takes combinations of REQ_FLUSH and FUA. If a
device has write cache and can flush it, it should set REQ_FLUSH. If
the device can handle FUA writes, it should also set REQ_FUA.
All blk_queue_ordered() users are converted.
* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Nobody is making meaningful use of ORDERED_BY_TAG now and queue
draining for barrier requests will be removed soon which will render
the advantage of tag ordering moot. Kill ORDERED_BY_TAG. The
following users are affected.
* brd: converted to ORDERED_DRAIN.
* virtio_blk: ORDERED_TAG path was already marked deprecated. Removed.
* xen-blkfront: ORDERED_TAG case dropped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
loop implements FLUSH using fsync but was incorrectly setting its
ordered mode to DRAIN. Change it to DRAIN_FLUSH. In practice, this
doesn't change anything as loop doesn't make use of the block layer
ordered implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The ioctl path and the scsi tape path were not accounting
for their additions to the queue depth.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: pvhvm: make it clearer that XEN_UNPLUG_* define bits in a bitfield
xen: pvhvm: rename xen_emul_unplug=ignore to =unnnecessary
xen: pvhvm: allow user to request no emulated device unplug
Create /sys/block/loopX/loop directory and provide these attributes:
- backing_file
- autoclear
- offset
- sizelimit
This loop directory is present only if loop device is configured.
To be used in util-linux-ng (and possibly elsewhere like udev rules)
where code need to get loop attributes from kernel (and not store
duplicate info in userspace).
Moreover loop ioctls are not even able to provide full backing
file info because of buffer limits.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Now that we have this API, switch the two in-kernel users to it.
Resolves an oops introduced by commit
1abec4fdbb.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It is not immediately clear what this option causes to become
ignored. The actual meaning is that it is not necessary to unplug the
emulated devices to safely use the PV ones, even if the platform does
not support the unplug protocol. (pressumably the user will only add
this option if they have ensured that their domain configuration is
safe).
I think xen_emul_unplug=unnecessary better captures this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Return of the bi_rw tests is no longer bool after commit 74450be1. But
results of such tests are stored in bools. This doesn't fit in there
for some compilers (gcc 4.5 here), so either use !! magic to get real
bools or use ulong where the result is assigned somewhere.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If kmalloc() fails then cleanup and return failure (-1).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The drivers for Xilinx' SystemACE and physically mapped MTDs were missing
prototypes for of_address_to_resource(). This patch adds the necessary
headers.
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
It was a now abandoned attempt to throttle resync bandwidth
based on the delay it causes on the bulk data socket.
It has no userbase yet, and has been disabled by
9173465ccb51c09cc3102a10af93e9f469a0af6f already.
This removes the now unused code.
The basic feature, namely using up "idle" bandwith
of network and disk IO subsystem, with minimal impact
to application IO, is being reimplemented differently.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
put_user() may fail, if so return -EFAULT.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If there's no feature-barrier key in xenstore, then it means its a fairly
old backend which does uncached in-order writes, which means ORDERED_DRAIN
is appropriate.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When barriers are supported, then use QUEUE_ORDERED_TAG to tell the block
subsystem that it doesn't need to do anything else with the barriers.
Previously we used ORDERED_DRAIN which caused the block subsystem to
drain all pending IO before submitting the barrier, which would be
very expensive.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The struct cont_t is just a set of virtual function pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use memdup_user when user data is immediately copied into the
allocated region. Some checkpatch cleanups in nearby code.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Chirag Kantharia <chirag.kantharia@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: cleanup interrupt_not_for_us
In the case of MSI/MSIX interrutps, we don't need to check
if the interrupt is for us, and in the case of the intx interrupt
handler, when checking if the interrupt is for us, we don't need
to check if we're using MSI/MSIX, we know we're not.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: change printks to dev_warn, etc.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: separate cmd_alloc() and cmd_special_alloc()
cmd_alloc() took a parameter which caused it to either allocate
from a pre-allocated pool, or allocate using pci_alloc_consistent.
This parameter is always known at compile time, so this would
be better handled by breaking the function into two functions
and differentiating the cases by function names. Same goes
for cmd_free().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: use consistent variable names
"h", for the hba structure and "c" for the command structures.
and get rid of trivial CCISS_LOCK macro.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: forbid hard reset of 640x boards
The 6402/6404 are two PCI devices -- two Smart Array controllers
-- that fit into one slot. It is possible to reset them independently,
however, they share a battery backed cache module. One of the pair
controls the cache and the 2nd one access the cache through the first
one. If you reset the one controlling the cache, the other one will
not be a happy camper. So we just forbid resetting this conjoined
mess.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: sanitize max commands
Some controllers might try to tell us they support 0 commands
in performant mode. This is a lie told by buggy firmware.
We have to be wary of this lest we try to allocate a negative
number of command blocks, which will be treated as unsigned,
and get an out of memory condition.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: Fix hard reset code.
Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers. Instead,
in these cases we can get them to reset via the "doorbell" register.
This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work". Once the performant mode code was added, if the controller
does not reset, it remains in performant mode. The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work. So the reset needs to be fixed.
Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800). We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted. In those cases we ignore the controller,
as any commands outstanding on it will result in stale completions.
To sum up, we try to do a better job of resetting the controller if
"reset_devices" is set, and if it doesn't work, we ignore that
controller.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_reset_devices()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Rationale for this is that I will also need to use this code
in fixing kdump host reset code prior to having the hba structure.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_enter_performant_mode
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_wait_for_mode_change_ack()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: make cciss_put_controller_into_performant_mode as __devinit
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_p600_dma_prefetch_quirk()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_enable_scsi_prefetch()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out CISS_signature_present()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_find_board_params
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: fix leak of ioremapped memory
in cciss_pci_init error path.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_wait_for_board_ready()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_find_memory_BAR()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: remove board_id parameter from cciss_interrupt_mode()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_lookup_board_id
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: save pdev pointer in per hba structure early to avoid passing it around so much.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: Set the performant mode bit in the scsi half of the driver
In a couple of places, the performant mode bit wasn't being set in
the scsi half of the driver, causing commands to seem to hang. Use
enqueue_cmd_and_start_io() where appropriate. This fixes a bug that
echo engage scsi > /proc/driver/cciss/cciss0
would hang.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is just bd_openers, protected by the bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is just bd_openers, protected by the bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Same approach as blkfront_closing:
* Grab the bdev safely, holding the info mutex.
* Zap xbdev safely, holding the info mutex.
* Try bdev removal safely, holding bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
We cannot read backend state within bdev operations, because it risks
grabbing the state change before xenbus gets to do it.
Fixed by tracking deferral with a frontend switch to Closing. State
exposure isn't strictly necessary, but the backends won't mind.
For a 'clean' deferral this seems actually a more decent protocol than
raising errors.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We need not mind if users grab a late handle on a closing disk. We
probably even should not. But we have to make sure it's not a dead
one already
Let the bdev deal with a gendisk deleted under its feet. Takes the
info mutex to decide a race against backend closing.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bdev .open/.release fops race against backend switches to Closing,
handled by the XenBus thread.
The original code attempted to serialize block device holders and
xenbus only via bd_mutex. This is insufficient, the info->bd pointer
may already be stale (or null) while xenbus tries to bump up the
refcount.
Protect blkfront_info with a dedicated mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* Current blkfront_closing is rather a xlvbd_release_gendisk.
Renamed in preparation of later patches (need the name again).
* Removed the misleading comment -- this only applied to the backend
switch handler, and the queue is already flushed btw.
* Break out the xenbus call, callers know better when to switch
frontend state.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The call to del_gendisk follows an non-refcounted gd->queue
pointer. We release the last ref in blk_cleanup_queue. Fixed by
reordering releases accordingly.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Fix:
drivers/block/xen-blkfront.c: In function ‘blkfront_connect’:
drivers/block/xen-blkfront.c:933: warning: enumeration value ‘BLKIF_STATE_DISCONNECTED’ not handled in switch
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Support dynamic resizing of virtual block devices. This patch supports
both file backed block devices as well as physical devices that can be
dynamically resized on the host side.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Unfortunately commit "blkfront: fixes for 'xm block-detach ... --force'"
still wasn't quite right - there was a reference to freed memory left
from blkfront_closing().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Prevent prematurely freeing 'struct blkfront_info' instances (when the
xenbus data structures are gone, but the Linux ones are still needed).
Prevent adding a disk with the same (major, minor) [and hence the same
name and sysfs entries, which leads to oopses] when the previous
instance wasn't fully de-allocated yet.
This still doesn't address all issues resulting from forced detach:
I/O submitted after the detach still blocks forever, likely preventing
subsequent un-mounting from completing. It's not clear to me (not
knowing much about the block layer) how this can be avoided.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
All Xen frontend drivers have a couple of identically named functions which
makes figuring out which device went wrong from a stacktrace harder than it
needs to be. Rename them to something specificto the device type.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As a preparation for the removal of the big kernel
lock in the block layer, this removes the BKL
from the common ioctl handling code, moving it
into every single driver still using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
use REQ_FLUSH flag instead.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
REQ_FLUSH flag enables us to kill ps3disk_prepare_flush().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
