[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
with eDP + DP, each display use one pipe. after DP unplugged, eDP switch
from one pipe to two pipes -- pipe split. dpp1_cm_set_regamma_pwl will
be executed too. The duration from switch single pipe to dual pipes is a
little long which could let eDP enter PSR mode. upon two pipes for eDP
are setup, eDP PHY is disabled. front pipe is not really running to
fetch data from frame buffer. i.e., dchubp is not in normal working
status. execution of hubbub1_wm_change_req_wa may cause p-state warning.
[How]
disable eDP PSR before dc_commit_state. psr is disabled when execute
hubbub1_wm_change_req_wa.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register key for AE or QA do regression test. New edid status for
check.
[How]
Add register key edid_read_retry_times.
Add new edid status EDID_FALL_BACK.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is using pixelclk AVFS for dppclk, that would cause issue.
[How]
To use dispclk AVFS for both dispclk and dppclk. There would choose
dppclk for request voltage when dispclk wouldn't be updated case. If
dispclk need to be updated, then it'll choose the bigger one from dppclk
and dispclk for request voltage.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC is very fast at link training and stream enablement
which causes issues such as blackscreens for non-compliant
monitors.
[How]
After debugging with scaler vendors we implement the
minimum delays at the necessary locations to ensure
the monitor does not hang. Delays are generic due to
lack of IEEE OUI information on the failing displays.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sprcified monitor scalar cannot recognize timing
change on demand. Once the link phy disable and enable
during a short period then the Sink protection mechanism
could keep the screen in blank and cannot be recoverred.
[How]
To add 100ms delay between enable link phy and link training.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And only set to 400us if LTTPR is not present.
Before this piece of logic is interwined with LTTPR support.
Now we will default to 3.2ms aux timeout even if LTTPR support is not
enabled by driver.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Want to make use of detile buffer of all 4 pipes to maximize amount of
data stored to hide certain memory latency cases.
[How]
In case of 1 plane and 1 stream, program 4 pipes to each retrieve 1/4 of
plane later mixed together by the MPCs. Added support for transition
from 4 to 1 MPC to 2 to 1 MPC or no pipe split case and vice versa.
Currently, only enabled if debug flag is set.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain display configurations we want to allow PSTATE
switch when one display can switch in VACTIVE and the
other display can switch in VBLANK
[How]
Add extra condition to dcn2 pstate support check
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
