Dropping packets from aggregation sessions is usually not a good idea, as
it might upset the synchronization of the BlockAck receive window of the
remote node. The use of the retry_tx parameter to reset/tx-drain functions
also seemed a bit arbitrary.
This patch removes this parameter altogether and ensures that pending tx
frames are not dropped for no good reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completing frame transmission can fail if the rx engine is stopped
prematurely, as the hw might be waiting for an ACK from the other side.
Shutting down tx before rx might make the DMA shutdown more reliable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of variable packet_beacon might be uninitialized in the three files.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hardware is not ready, il4965_pci_probe() breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_iomap() fails in mwl8k_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
There is a similar issue when priv->rxd_ops is NULL in mwl8k_probe_hw().
The patch adds proper error code return values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AP responds with appropriate status code, we forward that
code correctly to cfg80211. But sometimes when there is no
response from AP, our firmware uses proprietary status codes.
We will map authentication timeout to WLAN_STATUS_AUTH_TIMEOUT
and other proprietary codes to WLAN_STATUS_UNSPECIFIED_FAILURE.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rt2800 hardware isn't capable of reporting the TX status of
BlockAckReq frames implement the TX status handling of BARs in
rt2x00lib. We keep track of all BARs that are send out and try to
match incoming BAs to the appropriate BARs. This allows us to report a
more or less accurate TX status for BAR frames which in turn improves
BA session stability.
This is loosley based on Christian Lamparter's patch for carl9170
"carl9170: fix HT peer BA session corruption".
We have to walk the list of pending BARs for every rx'red BA even
though most BAs don't belong to any of these BARs as they are just
acknowledging an AMPDU. To keep that overhead low use RCU which allows
us to walk the list of pending BARs without the need to acquire a lock.
This however requires us to _copy_ relevant information from the BAR
(RA, TA, control field, start sequence number) into our BAR list entry.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing break statement so SHARED_KEY authentication doesn't
work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were no break statements in this switch statement so everything
used the default settings. Per Walter Harms's suggestion, I've replaced
the switch statement and done a little cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ray_cs.c:
the a_current_ess_id is "Null terminated unless ESSID_SIZE long"
so we need buffer it with '\0' firstly, before using strlen or %s.
additional information:
in drivers/net/wireless/rayctl.h:
"NULL terminated unless 32 long" is a comment at line 616, 664
ESSID_SIZE is 32, at line 190
in include/uapi/linux/wireless.h:
IW_ESSID_MAX_SIZE is also 32
in drivers/net/wireless/ray_cs.c:
use strncpy for it, without '\0' terminated, at line 639
use memcpy for it, assume not '\0' terminated in line 1092..1097
buffer it with '\0' firstly, before using %s, in line 2576, 2598..2600
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also when things go wrong (queues don't get emtpy), try to
get some data from the HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Writing 130 dwords into the device one by one is
rather inefficient, every one needs to lock, grab
NIC access (a few register reads/writes) and then
write the address and data registers.
Use the new memory clearing function to make this
easier and faster.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending a NULL pointer to iwl_trans_write_mem allows now
to zero SRAM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enabling the RF-kill interrupt is sufficient for getting
RF-kill notifications, and no other interrupt is needed
as the device isn't functional when suspended and will be
restarted/reconfigured when mac80211 resumes it later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dma_addr_t type is a scalar value, so it should
just be assigned, not memset.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Improves stability on affected devices and also fixes the Tx IQ calibration
related regression on some AR9340 devices such as the TP-Link TL-WDR4300.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the beacon timestamp once during "transmission" so the
monitor interface also gets a timestamped beacon.
Also use a common base between TX timestamp and RX
mactime. This eliminates "TX" path delay, which shows up
as a constant error in Toffset.
Get the global TSF once before iterating over all RX HWs,
so they all set a mactime with the same time base.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
This feature is still experimental.
The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.
The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9550, program the synth value based on the ref. clock.
The logic for AR9550 is similar to AR9330, but keep the code
separate since changes for AR9330 are required - which would be
done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If queues are stopped in mwl8k_stop,
these should be started in mwl8k_start
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station deauths, we do not delete the streams with state
AMPDU_STREAM_NEW and these remain created forever. Fix this issue by
removing such streams in the driver
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever TX ring is drained, priv->tx_wait still points
to a valid completion. Making sure that it points to
NULL before returning from the mwl8k_tx_wait_empty
check.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AGC calibration is to be done, a GPM message with the
payload, MCI_GPM_WLAN_CAL_REQ has to be sent. Currently this falls
within the IQ-CAL code block which is incorrect. Fix this by using
a separate variable to decide when IQ-CAL is to be done separately
and call ar9003_mci_init_cal_req correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds handler to clean PCIe TX rings after disconnect
or bss stop is called for PCIe based mwifiex driver.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.
Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware is required to support
a) Add support for additional ampdu streams
b) Handle corresponding watchdog events to destroy ampdu streams
Bumping firmware API version by one.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.
This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.
Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.
Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set ACK policy to NORMAL when its not going to
be an AMPDU packet.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ampdu stream index can be derived from stream->idx.
So we no longer need stream->txq_idx, hence removing it.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
