Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
Pull regulator updates from Mark Brown:
"This is mostly a drivers update including a couple of new drivers but
we do have some fixes and improvements to the core as well.
- Make sure we don't log spuriously about uncontrollable regulators.
- Don't use delays when we should use sleeps for regulators with
larger ramp times.
- Support for MediaTek MT6358 and MT6366, Richtek RT5759 and Silicon
Mitus SM5703"
* tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: scmi: Fix refcount leak in scmi_regulator_probe
regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
regulator: qcom_smd: Fix up PM8950 regulator configuration
regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
regulator: core: Add error flags to sysfs attributes
regulator: dt-bindings: qcom,rpmh: document vdd-l7-bob-supply on PMR735A
regulator: dt-bindings: qcom,rpmh: document supplies per variant
regulator: dt-bindings: qcom,rpmh: update maintainers
regulator: mt6315: Enforce regulator-compatible, not name
regulator: pca9450: Enable DVS control via PMIC_STBY_REQ
regulator: pca9450: Make warm reset on WDOG_B assertion
regulator: Add property for WDOG_B warm reset
regulator: pca9450: Make I2C Level Translator configurable
regulator: Add property for I2C level shifter
regulator: sm5703: Correct reference to the common regulator schema
regulator: sm5703-regulator: Add regulators support for SM5703 MFD
dt-bindings: regulator: Add bindings for Silicon Mitus SM5703 regulators
regulator: richtek,rt4801: parse GPIOs per regulator
regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod feature
regulator: core: Sleep (not delay) in set_voltage()
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Support zero-out using TRIM for eMMC
- Allow to override the busy-timeout for the ioctl-cmds
MMC host:
- Continued the conversion of DT bindings into the JSON schema
- jz4740: Apply DMA engine limits to maximum segment size
- mmci_stm32: Use a buffer for unaligned DMA requests
- mmc_spi: Enabled high-speed modes via parsing of DT
- omap: Make clock management to be compliant with CCF
- renesas_sdhi:
- Support eMMC HS400 mode for R-Car V3H ES2.0
- Don't allow support for eMMC HS400 for R-Car V3M/D3
- sdhci_am654: Fix problem when SD card slot lacks the card detect
line
- sdhci-esdhc-imx: Add support for the imx8dxl variant
- sdhci-brcmstb: Enable support for clock gating to save power
- sdhci-msm:
- Add support for the sdx65 variant
- Add support for the sm8150 variant
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"
* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci-of-arasan: Add NULL check for data field
mmc: core: Support zeroout using TRIM for eMMC
mmc: sdhci-brcmstb: Fix compiler warning
mmc: sdhci-msm: Add compatible string check for sdx65
dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
mmc: sdhci-msm: Add compatible string check for sm8150
dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
mmc: sdhci-msm: Add SoC specific compatibles
dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
mmc: sdhci-brcmstb: Enable Clock Gating to save power
mmc: sdhci-brcmstb: Re-organize flags
mmc: mmci: Remove custom ios handler
mmc: atmel-mci: Simplify if(chan) and if(!chan)
mmc: core: use kobj_to_dev()
dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
mmc: core: Add CIDs for cards to the entropy pool
mmc: core: Allows to override the timeout value for ioctl() path
mmc: sdhci-omap: Use of_device_get_match_data() helper
...
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for the Microchip LAN966x SoC
- PMBus driver for Infineon Digital Multi-phase xdp152 family
controllers
Chip support added to existing drivers:
- asus-ec-sensors:
- Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO, and
ProArt X570 Creator WIFI
- External temperature sensor support for ASUS WS X570-ACE
- nct6775:
- Support for I2C driver
- Support for ASUS PRO H410T / PRIME H410M-R /
ROG X570-E GAMING WIFI II
- lm75:
- Support for - Atmel AT30TS74
- pmbus/max16601:
- Support for MAX16602
- aquacomputer_d5next:
- Support for Aquacomputer Farbwerk
- Support for Aquacomputer Octo
- jc42:
- Support for S-34TS04A
Kernel API changes / clarifications:
- The chip parameter of with_info API is now mandatory
- New hwmon_device_register_for_thermal API call for use by the
thermal subsystem
Improvements:
- PMBus and JC42 drivers now register with thermal subsystem
- PMBus drivers now support get_voltage/set_voltage power operations
- The adt7475 driver now supports pin configuration
- The lm90 driver now supports setting extended range temperatures
configuration with a devicetree property
- The dell-smm driver now registers as cooling device
- The OCC driver delays hwmon registration until requested by
userspace
... and various other minor fixes and improvements"
* tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (71 commits)
hwmon: (aquacomputer_d5next) Fix an error handling path in aqc_probe()
hwmon: (sl28cpld) Fix typo in comment
hwmon: (pmbus) Check PEC support before reading other registers
hwmon: (dimmtemp) Fix bitmap handling
hwmon: (lm90) enable extended range according to DTS node
dt-bindings: hwmon: lm90: add ti,extended-range-enable property
dt-bindings: hwmon: lm90: add missing ti,tmp461
hwmon: (ibmaem) Directly use ida_alloc()/free()
hwmon: Directly use ida_alloc()/free()
hwmon: (asus-ec-sensors) fix Formula VIII definition
dt-bindings: trivial-devices: Add xdp152
hwmon: (sl28cpld-hwmon) Use HWMON_CHANNEL_INFO macro
hwmon: (pwm-fan) Use HWMON_CHANNEL_INFO macro
hwmon: (peci/dimmtemp) Use HWMON_CHANNEL_INFO macro
hwmon: (peci/cputemp) Use HWMON_CHANNEL_INFO macro
hwmon: (mr75203) Use HWMON_CHANNEL_INFO macro
hwmon: (ltc2992) Use HWMON_CHANNEL_INFO macro
hwmon: (as370-hwmon) Use HWMON_CHANNEL_INFO macro
hwmon: Make chip parameter for with_info API mandatory
thermal/drivers/thermal_hwmon: Use hwmon_device_register_for_thermal()
...
Pull arm64 updates from Catalin Marinas:
- Initial support for the ARMv9 Scalable Matrix Extension (SME).
SME takes the approach used for vectors in SVE and extends this to
provide architectural support for matrix operations. No KVM support
yet, SME is disabled in guests.
- Support for crashkernel reservations above ZONE_DMA via the
'crashkernel=X,high' command line option.
- btrfs search_ioctl() fix for live-lock with sub-page faults.
- arm64 perf updates: support for the Hisilicon "CPA" PMU for
monitoring coherent I/O traffic, support for Arm's CMN-650 and
CMN-700 interconnect PMUs, minor driver fixes, kerneldoc cleanup.
- Kselftest updates for SME, BTI, MTE.
- Automatic generation of the system register macros from a 'sysreg'
file describing the register bitfields.
- Update the type of the function argument holding the ESR_ELx register
value to unsigned long to match the architecture register size
(originally 32-bit but extended since ARMv8.0).
- stacktrace cleanups.
- ftrace cleanups.
- Miscellaneous updates, most notably: arm64-specific huge_ptep_get(),
avoid executable mappings in kexec/hibernate code, drop TLB flushing
from get_clear_flush() (and rename it to get_clear_contig()),
ARCH_NR_GPIO bumped to 2048 for ARCH_APPLE.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (145 commits)
arm64/sysreg: Generate definitions for FAR_ELx
arm64/sysreg: Generate definitions for DACR32_EL2
arm64/sysreg: Generate definitions for CSSELR_EL1
arm64/sysreg: Generate definitions for CPACR_ELx
arm64/sysreg: Generate definitions for CONTEXTIDR_ELx
arm64/sysreg: Generate definitions for CLIDR_EL1
arm64/sve: Move sve_free() into SVE code section
arm64: Kconfig.platforms: Add comments
arm64: Kconfig: Fix indentation and add comments
arm64: mm: avoid writable executable mappings in kexec/hibernate code
arm64: lds: move special code sections out of kernel exec segment
arm64/hugetlb: Implement arm64 specific huge_ptep_get()
arm64/hugetlb: Use ptep_get() to get the pte value of a huge page
arm64: kdump: Do not allocate crash low memory if not needed
arm64/sve: Generate ZCR definitions
arm64/sme: Generate defintions for SVCR
arm64/sme: Generate SMPRI_EL1 definitions
arm64/sme: Automatically generate SMPRIMAP_EL2 definitions
arm64/sme: Automatically generate SMIDR_EL1 defines
arm64/sme: Automatically generate defines for SMCR
...
Pull EDAC updates from Borislav Petkov:
- Switch ghes_edac to use the CPER error reporting routines and
simplify the code considerably this way
- Rip out the silly edac_align_ptr() contraption which was computing
the size of the private structures of each driver and thus allowing
for a one-shot memory allocation. This was clearly unnecessary and
confusing so switch to simple and boring kmalloc* calls.
- Last but not least, the usual garden variety of fixes, cleanups and
improvements all over EDAC land
* tag 'edac_updates_for_v5.19_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/xgene: Fix typo processsors -> processors
EDAC/i5100: Remove unused inline function i5100_nrecmema_dm_buf_id()
EDAC: Use kcalloc()
EDAC/ghes: Change ghes_hw from global to static
EDAC/armada_xp: Use devm_platform_ioremap_resource()
EDAC/synopsys: Add a SPDX identifier
EDAC/synopsys: Add driver support for i.MX platforms
EDAC/dmc520: Don't print an error for each unconfigured interrupt line
EDAC/mc: Get rid of edac_align_ptr()
EDAC/device: Sanitize edac_device_alloc_ctl_info() definition
EDAC/device: Get rid of the silly one-shot memory allocation in edac_device_alloc_ctl_info()
EDAC/pci: Get rid of the silly one-shot memory allocation in edac_pci_alloc_ctl_info()
EDAC/mc: Get rid of silly one-shot struct allocation in edac_mc_alloc()
efi/cper: Reformat CPER memory error location to more readable
EDAC/ghes: Unify CPER memory error location reporting
efi/cper: Add a cper_mem_err_status_str() to decode error description
powerpc/85xx: Remove fsl,85... bindings
Pull interrupt handling updates from Thomas Gleixner:
"Core code:
- Make the managed interrupts more robust by shutting them down in
the core code when the assigned affinity mask does not contain
online CPUs.
- Make the irq simulator chip work on RT
- A small set of cpumask and power manageent cleanups
Drivers:
- A set of changes which mark GPIO interrupt chips immutable to
prevent the GPIO subsystem from modifying it under the hood. This
provides the necessary infrastructure and converts a set of GPIO
and pinctrl drivers over.
- A set of changes to make the pseudo-NMI handling for GICv3 more
robust: a missing barrier and consistent handling of the priority
mask.
- Another set of GICv3 improvements and fixes, but nothing
outstanding
- The usual set of improvements and cleanups all over the place
- No new irqchip drivers and not even a new device tree binding!
100+ interrupt chips are truly enough"
* tag 'irq-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irqchip: Add Kconfig symbols for sunxi drivers
irqchip/gic-v3: Fix priority mask handling
irqchip/gic-v3: Refactor ISB + EOIR at ack time
irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
genirq/irq_sim: Make the irq_work always run in hard irq context
irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375, A38x, A39x
irqchip/gic: Improved warning about incorrect type
irqchip/csky: Return true/false (not 1/0) from bool functions
irqchip/imx-irqsteer: Add runtime PM support
irqchip/imx-irqsteer: Constify irq_chip struct
irqchip/armada-370-xp: Enable MSI affinity configuration
irqchip/aspeed-scu-ic: Fix irq_of_parse_and_map() return value
irqchip/aspeed-i2c-ic: Fix irq_of_parse_and_map() return value
irqchip/sun6i-r: Use NULL for chip_data
irqchip/xtensa-mx: Fix initial IRQ affinity in non-SMP setup
irqchip/exiu: Fix acknowledgment of edge triggered interrupts
irqchip/gic-v3: Claim iomem resources
dt-bindings: interrupt-controller: arm,gic-v3: Make the v2 compat requirements explicit
irqchip/gic-v3: Relax polling of GIC{R,D}_CTLR.RWP
irqchip/gic-v3: Detect LPI invalidation MMIO registers
...
Pull ata updates from Damien Le Moal:
"For this cycle, the libata.force kernel parameter changes stand out.
Beside that, some small cleanups in various drivers. In more detail:
- Changes to the pata_mpc52xx driver in preparation for powerpc's
asm/prom.h cleanup, from Christophe.
- Improved ATA command allocation, from John.
- Various small cleanups to the pata_via, pata_sil680, pata_ftide010,
sata_gemini, ahci_brcm drivers and to libata-core, from Sergey,
Diego, Ruyi, Mighao and Jiabing.
- Add support for the RZ/G2H SoC to the rcar-sata driver, from Lad.
- AHCI RAID ID cleanup, from Dan.
- Improvement to the libata.force kernel parameter to allow most
horkage flags to be manually forced for debugging drive issues in
the field without needing recompiling a kernel, from me"
* tag 'ata-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_ftide010: Remove unneeded ERROR check before clk_disable_unprepare
doc: admin-guide: Update libata kernel parameters
ata: libata-core: Allow forcing most horkage flags
ata: libata-core: Improve link flags forced settings
ata: libata-core: Refactor force_tbl definition
ata: libata-core: cleanup ata_device_blacklist
ata: simplify the return expression of brcm_ahci_remove
ata: Make use of the helper function devm_platform_ioremap_resource()
ata: libata-core: replace "its" with "it is"
ahci: Add a generic 'controller2' RAID id
dt-bindings: ata: renesas,rcar-sata: Add r8a774e1 support
ata: pata_via: fix sloppy typing in via_do_set_mode()
ata: pata_sil680: fix result type of sil680_sel{dev|reg}()
ata: libata-core: fix parameter type in ata_xfer_mode2shift()
libata: Improve ATA queued command allocation
ata: pata_mpc52xx: Prepare cleanup of powerpc's asm/prom.h
Pull input fixes from Dmitry Torokhov:
"A small fixup to ili210x touchscreen driver, and updated maintainer
entry for the device tree binding of Mediatek 6779 keypad:
- fix reset timing of Ilitek touchscreens
- update maintainer entry of DT binding of Mediatek 6779 keypad"
* tag 'input-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ili210x - use one common reset implementation
Input: ili210x - fix reset timing
dt-bindings: input: mediatek,mt6779-keypad: update maintainer
NAND core:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR core changes:
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull ARM SoC fixes from Arnd Bergmann:
"The SoC bug fixes have calmed down sufficiently, there is one minor
update for the MAINTAINERS file, and few bug fixes for dts
descriptions:
- Updates to the BananaPi R2-Pro (rk3568) dts to match production
hardware rather than the prototype version.
- Qualcomm sm8250 soundwire gets disabled on some machines to avoid
crashes
- A number of aspeed SoC specific fixes, addressing incorrect pin
cotrol settings, some values in the romed8hm board, and a revert
for an accidental removal of a DT node"
* 'arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: omap: remove me as a maintainer
ARM: dts: aspeed: Add video engine to g6
ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values
ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
ARM: dts: aspeed-g6: add FWQSPI group in pinctrl dtsi
dt-bindings: pinctrl: aspeed-g6: add FWQSPI function/group
pinctrl: pinctrl-aspeed-g6: add FWQSPI function-group
dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
arm64: dts: qcom: sm8250: don't enable rx/tx macro by default
arm64: dts: rockchip: Add gmac1 and change network settings of bpi-r2-pro
arm64: dts: rockchip: Change io-domains of bpi-r2-pro
Pull devicetree fixes from Rob Herring:
- Drop unused 'max-link-speed' in Apple PCIe
- More redundant 'maxItems/minItems' schema fixes
- Support values for pinctrl 'drive-push-pull' and 'drive-open-drain'
- Fix redundant 'unevaluatedProperties' in MT6360 LEDs binding
- Add missing 'power-domains' property to Cadence UFSHC
* tag 'devicetree-fixes-for-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pci: apple,pcie: Drop max-link-speed from example
dt-bindings: Drop redundant 'maxItems/minItems' in if/then schemas
dt-bindings: pinctrl: Allow values for drive-push-pull and drive-open-drain
dt-bindings: leds-mt6360: Drop redundant 'unevaluatedProperties'
dt-bindings: ufs: cdns,ufshc: Add power-domains
Another round of removing redundant minItems/maxItems when 'items' list is
specified. This time it is in if/then schemas as the meta-schema was
failing to check this case.
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for IIO
Link: https://lore.kernel.org/r/20220503162738.3827041-1-robh@kernel.org
A common mistake when writing a device tree for a platform that is using
GICv3 with ancient CPUs is to overlook the MMIO frames that implement
the GICv2 compatibility feature, because this feature is implemented by
the CPUs and not by the GIC itself.
The compatibility feature itself is optional (all the modern
implementations have dropped it), but is present in all the ARM Ltd
implementations of the ARMv8.0 architecture (A3x, A53, A57, A72, A73),
and many others from various implementers.
Make it explicit that GICC, GICH and GICV are required for these CPUs.
Also take this opportunity to update my email address, as people keep
sending them to the wrong place...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220409101617.268796-1-maz@kernel.org
The RPMH regulator binding covers several devices with different
regulator supplies, so it uses patterns matching broad range of these
supplies. This works fine but is not specific and might miss actual
mistakes when a wrong supply property is used for given variant.
Describe the supplies depending on the compatible, using a defs-allOf
method.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220426105501.73200-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6315 PMIC dt-binding should enforce that one of the valid
regulator-compatible is set in each regulator node. However it was
mistakenly matching against regulator-name instead.
Fix the typo. This not only fixes the compatible verification, but also
lifts the regulator-name restriction, so that more meaningful names can
be set for each platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220429201325.2205799-1-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull hwmon fixes from Guenter Roeck:
- Work around a hardware problem in the delta-ahe50dc-fan driver
- Explicitly disable PEC in PMBus core if not enabled
- Fix negative temperature values in f71882fg driver
- Fix warning on removal of adt7470 driver
- Fix CROSSHAIR VI HERO name in asus_wmi_sensors driver
- Fix build warning seen in xdpe12284 driver if
CONFIG_SENSORS_XDPE122_REGULATOR is disabled
- Fix type of 'ti,n-factor' in ti,tmp421 driver bindings
* tag 'hwmon-for-v5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus) delta-ahe50dc-fan: work around hardware quirk
hwmon: (pmbus) disable PEC if not enabled
hwmon: (f71882fg) Fix negative temperature
dt-bindings: hwmon: ti,tmp421: Fix type for 'ti,n-factor'
hwmon: (adt7470) Fix warning on module removal
hwmon: (asus_wmi_sensors) Fix CROSSHAIR VI HERO name
hwmon: (xdpe12284) Fix build warning seen if CONFIG_SENSORS_XDPE122_REGULATOR is disabled
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.18-rc5 for some
reported issues and new quirks. They include:
- dwc3 driver fixes
- xhci driver fixes
- typec driver fixes
- new usb-serial driver ids
- added new USB devices to existing quirk tables
- other tiny fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits)
usb: phy: generic: Get the vbus supply
usb: dwc3: gadget: Return proper request status
usb: dwc3: pci: add support for the Intel Meteor Lake-P
usb: dwc3: core: Only handle soft-reset in DCTL
usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind()
usb: misc: eud: Fix an error handling path in eud_probe()
usb: core: Don't hold the device lock while sleeping in do_proc_control()
usb: dwc3: Try usb-role-switch first in dwc3_drd_init
usb: dwc3: core: Fix tx/rx threshold settings
usb: mtu3: fix USB 3.0 dual-role-switch from device to host
xhci: Enable runtime PM on second Alderlake controller
usb: dwc3: fix backwards compat with rockchip devices
dt-bindings: usb: samsung,exynos-usb2: add missing required reg
usb: misc: fix improper handling of refcount in uss720_probe()
USB: Fix ehci infinite suspend-resume loop issue in zhaoxin
usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant
usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY
usb: typec: ucsi: Fix role swapping
usb: typec: ucsi: Fix reuse of completion structure
usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions
...
Pull ARM SoC fixes from Arnd Bergmann:
- A fix for a regression caused by the previous set of bugfixes
changing tegra and at91 pinctrl properties.
More work is needed to figure out what this should actually be, but a
revert makes it work for the moment.
- Defconfig regression fixes for tegra after renamed symbols
- Build-time warning and static checker fixes for imx, op-tee, sunxi,
meson, at91, and omap
- More at91 DT fixes for audio, regulator and spi nodes
- A regression fix for Renesas Hyperflash memory probe
- A stability fix for amlogic boards, modifying the allowed cpufreq
states
- Multiple fixes for system suspend on omap2+
- DT fixes for various i.MX bugs
- A probe error fix for imx6ull-colibri MMC
- A MAINTAINERS file entry for samsung bug reports
* tag 'soc-fixes-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
Revert "arm: dts: at91: Fix boolean properties with values"
bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
Revert "arm64: dts: tegra: Fix boolean properties with values"
arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
ARM: dts: imx6ull-colibri: fix vqmmc regulator
MAINTAINERS: add Bug entry for Samsung and memory controller drivers
memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
...
Pull clk fixes from Stephen Boyd:
"A semi-large pile of clk driver fixes this time around.
Nothing is touching the core so these fixes are fairly well contained
to specific devices that use these clk drivers.
- Some Allwinner SoC fixes to gracefully handle errors and mark an
RTC clk as critical so that the RTC keeps ticking.
- Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
driver introduced this cycle. This has some devicetree bits acked
by riscv maintainers. We're fixing it now so that the prior
bindings aren't released in a major kernel version.
- Remove a reset on Microchip PolarFire SoCs that broke when enabling
CONFIG_PM.
- Set a min/max for the Qualcomm graphics clk. This got broken by the
clk rate range patches introduced this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
riscv: dts: microchip: reparent mpfs clocks
clk: microchip: mpfs: add RTCREF clock control
clk: microchip: mpfs: re-parent the configurable clocks
dt-bindings: rtc: add refclk to mpfs-rtc
dt-bindings: clk: mpfs: add defines for two new clocks
dt-bindings: clk: mpfs document msspll dri registers
riscv: dts: microchip: fix usage of fic clocks on mpfs
clk: microchip: mpfs: mark CLK_ATHENA as critical
clk: microchip: mpfs: fix parents for FIC clocks
clk: qcom: clk-rcg2: fix gfx3d frequency calculation
clk: microchip: mpfs: don't reset disabled peripherals
clk: sunxi-ng: fix not NULL terminated coccicheck error
