Drop a useless initialization step in the w83627hf driver. The comment
says that the W83627HF PWM2 can be disabled, but it can't. I suppose
this is a leftover from the w83781d driver (from which the w83627hf
driver is derived), as for example the W83782D had the ability to
disable PWM2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes w83627hf and w83627ehf drivers to reserve only ports
0x295-0x296, instead of full 0x290-0x297 range. While some other
sensors chips respond to all addresses in 0x290-0x297 range, Winbond
chips respond to 0x295-0x296 only (this behavior is implied by
documentation, and matches behavior observed on real systems). This is
not problem alone, as no BIOS was found to put something at these unused
addresses, and sensors chip itself provides nothing there as well.
But in addition to only respond to these two addresses, also BIOS
vendors report in their ACPI-PnP structures that there is some resource
at I/O address 0x295 of length 2. And when later this hwmon driver
attempts to request region with base 0x290/length 8, it fails as one
request_region cannot span more than one device.
Due to this we have to ask only for region this hardware really
occupies, otherwise driver cannot be loaded on systems with ACPI-PnP
enabled.
Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using s8 instead of u8 to store temperature register values saves a
few instructions on sysfs file read. The very same was done for
several other drivers a while ago (lm63, lm83, lm90...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
Convert the w83l785ts driver to use dynamic sysfs callbacks. This is a
small driver so the benefit is thin, but still worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
Discard a common out-of-date comment in 5 hardware monitoring drivers.
The hardware monitoring chip drivers are no more setting sensor limits
at initialization time, for quite some time already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/lm78.c | 1 -
drivers/hwmon/via686a.c | 1 -
drivers/hwmon/w83627hf.c | 1 -
drivers/hwmon/w83781d.c | 1 -
drivers/hwmon/w83792d.c | 1 -
5 files changed, 5 deletions(-)
Do not enable the VIA VT82C686A/B integrated sensors by default, as
disabled sensors usually means that this feature is not used so the
values won't make any sense. This has been confusing many users in the
past:
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1786http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1811http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=2052
It is still possible to forcibly enable the sensors by using the
force_addr module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/hwmon/via686a | 17 +++++++++++++++--
drivers/hwmon/via686a.c | 18 +++++++++++-------
2 files changed, 26 insertions(+), 9 deletions(-)
We can save 0.5kB of data in the via686a driver.
From: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 2/2: convert to use dynamic sysfs accessors
This patch converts adm9240 to use Yani Ioannou's dynamic sysfs callbacks,
reducing driver memory footprint from 16312 to 14104 bytes on 2.6.14-rc1,
removing the old driver macro mess.
Run tested on Intel SE440BX-2 mobo.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 1/2: cleanups:
o remove i2c read/write wrapper interface as it does nothing,
o change kmalloc + memset to kzalloc
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Handle dmi_system_check() elegantly, now that my bugfix is upstream.
- Add support for the X41 and R52.
- Cleanup some comments do I do not have to keep updating them with each
new whitelisted laptop.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove the relative input device
- Add an absolute input device
- Misc. cleanup and bug fixing
The patch is sizable due to the cleanup from removing the relative input
device (net -112 lines).
Signed-off-by: Robert Love <rml@novell.com>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the reset of the chips in w83627hf optional rather than the
default. This reset has been causing trouble several times already. It
may even go completely away unless it proves to be useful to at least
one user.
Closes bug #5168:
http://bugzilla.kernel.org/show_bug.cgi?id=5168
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the head comment of the smsc47m1 driver to mention all the
supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes to the i2c-isa design broke the force_addr parameter of
two hardware monitoring drivers as a side effect: sis5595 and via686a.
The last address test was in fact useless beforehand, and the redesign
turned it into a bug. I'm sorry about that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for the IBM Hard Drive Active Protection System (HDAPS), an
accelerometer found in most modern ThinkPads.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: consolidate fan helper
This patch consolidates the _set_fan_min() helper routine into the 2
line sysfs-callback wrapper that uses it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: number-skew to init
The temp, therm, fan, pwm callbacks all have an offset skew in the code
which accommodates attribute numbering conventions under
/sys/bus/i2c/devices/9191-6620/ (ie they start at 1)
This patch moves that skew into the declaration, and out of the
functions (except for therm, where we simplify from 2 skews to 1). The
declarative skew is clearer, less error-prone, and more efficient.
The use of 11+offset-4 below reflects the fact that the sysfs numbering
of these units is 4, 5, 6, but they use internal VLM units 11, 12, 13 to
measure the thermistor voltages.
There's one remaining skew factor, in *_crit callbacks below, because
there are no critical thresholds for voltages 0-10, only for those
supporting the thermistors.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new "dynamic sysfs callbacks", as introduced recently by Yani
Ioannou, in pc87360.
Note that this change isn't indiscriminate. Only those attributes that
would benefit from having an index (i.e., those which are
macro-repeated) have been converted.
This significantly shrinks the size of the module:
before: 49235 drivers/hwmon/pc87360.ko
after: 32532 drivers/hwmon/pc87360.ko
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the VID entries, so any future
Intel CPU will be detected as unknown rather than 9.0
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the common vid_from_reg function in lm78 rather than
reimplementing it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I see very little reason why vid_from_reg is inlined. It is not
exactly short, its parameters are seldom known in advance, and it is
never called in speed critical areas. Uninlining it should cause
little performance loss if any, and saves a signficant space as well
as compilation time.
As suggested by Alexey Dobriyan, I am leaving vid_to_reg inline for now,
as it is short and has a single user so far.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup hwmon-vid a bit, fixing typos, rewording some comments and
reindenting properly at places.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an unused macro and an outdated comment from the lm85 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move SENSORS_LIMIT from i2c-sensor.h to hwmon.h, as it is in no way
related to i2c.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Super-I/O find functions in hardware monitoring drivers can be tagged
__init as they are only called from functions themselves tagged __init.
Two of them (smsc47b397 and w83627ehf) already do, but the other four
of them (it87, pc87360, smsc47m1 and w83627hf) did not.
This saves a few bytes of memory after the drivers are loaded, 192 in
the case of the it87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds registration of hwmon class. Tested with help of i2c-stub.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to announce support for W83792D chip. This driver was developed
by Winbond Electronics Corp. I added sysfs attributes callbacks infrastructure
plus various code fixes and codingstyle cleanups. I would like to thank Winbond
for supporting free software.
This patch is against 2.6.13rc3 plus hwmon-class and hwmon-split.
Separate patch for documantation and hwmon class register will follow.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Chunhao Huang <DZShen@Winbond.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill all uses of i2c_is_isa_adapter except for the hybrid drivers (it87,
lm78, w83781d). The i2c-isa adapter not being registered with the i2c
core anymore, drivers don't have to fear being erroneously attached to
it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call the ISA chip drivers detection function directly instead of relying
on i2c_detect. The net effect is that address lists won't be handled
anymore, but they were mostly useless in the ISA case anyway (pc87360,
smsc47m1, smsc47b397 had already dropped them).
We don't need to handle multiple devices, all we may need is a way to
force a given address instead of the original one (some drivers already
do: sis5595, via686a, w83627hf), and, for drivers supporting multiple
chips, a way to force one given kind. All this may be added later on
demand, but I actually don't think there will be much demand.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All ISA hardware monitoring drivers (including hybrid drivers) now have
a hard dependency on i2c-isa, so they must select I2C_ISA. As a result,
CONFIG_I2C_ISA doesn't need to be left visible to the user. The good
thing here is that users will stop complaining that some driver doesn't
work just because they forgot to compile or load i2c-isa.
At this point, all drivers are working again and the cleanup phase can
begin.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the 10 ISA hardware monitoring drivers (it87, lm78, pc87360,
sis5595, smsc47b397, smsc47m1, via686a, w83627hf, w83627ehf, w83781d) to
explicitely register with i2c-isa. For hybrid drivers (it87, lm78,
w83781d), we now have two separate instances of i2c_driver, one for the
I2C interface of the chip, and one for ISA interface. In the long run,
the one for ISA will be replaced with a different driver type.
At this point, all drivers are working again, except for missing
dependencies in Kconfig.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies sensors chip drivers to make use of the new
sysfs class "hwmon".
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the sysfs class "hwmon" for use by hardware monitoring
(sensors) chip drivers. It also fixes up the related Kconfig/Makefile
bits.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Document the fact that the W83627EHG is compatible with the W83627EHF.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the separate client name for the LM78-J chip. This is really
only a later revision of the LM78, with almost no difference and
no difference the driver handles in any case.
This was the only client name that had a dash in it, and special care
had to be taken in libsensors because of it. As we plan to write a new
library soon, I'd like to get rid of this exception before we do.
As a nice side effect, it saves 876 bytes in lm78.ko.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The LM75 initialization is a bit agressive, it arbitrarily reconfigures
the chip. Make it only change the bit it needs. This is a port from
the 2.4 kernel version of the driver (lm_sensors).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes several instances of hwmon drivers kfree'ing the "wrong"
pointer; the existing code works somewhat by accident.
(akpm: plucked from Greg's queue based on lkml discussion. Finishes off the
patch from Jon Corbet)
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Coverity uncovered an off-by-one error in the fscpos driver, in function
set_temp_reset(). Writing to the temp3_reset sysfs file will lead to an
array overrun, in turn causing an I2C write to a random register of the
FSC Poseidon chip. Additionally, writing to temp1_reset and temp2_reset
will not work as expected. The fix is straightforward.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The adm9240 driver, in adm9240_detect(), allocates a structure. The
error path attempts to kfree() ->client field of it (second one),
resulting in an oops (or slab corruption) if the hardware is not present.
->client field in adm1026, adm1031, smsc47b397 and smsc47m1 is the first in
${HWMON}_data structure, but fix them too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few i2c drivers were not updated to use time_after() yet.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few split string in i2c (and now hwmon) drivers lack a joining space,
causing them to display incorrectly. This trivial patch fixes that up.
Please apply, thanks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Part 2: Move the driver files themselves.
Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.
From: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
