snd_soc_card_jack_new() allowed to create jack kcontrol without pins,
but did not create kcontrols. The jack would not have kcontrols if pins
were not going to be added.
This renames the old snd_soc_card_jack_new() to
snd_soc_card_jack_new_pins() for use when pins are provided or will be
added later. The new snd_soc_card_jack_new() appropriately creates a
jack for use without pins and adds a kcontrol.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Link: https://lore.kernel.org/r/20220408041114.6024-1-akihiko.odaki@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards have the codec IRQ hooked-up as normally, so the driver can
still do things like headset vs headphones and button-press detection,
but instead of using one of the JD pins of the codec, an external GPIO
is used to report the jack-presence switch status of the jack.
Add support for boards which have this setup and which specify which
external GPIO to use in the special Android AMCR0F28 ACPI device.
And add a quirk for the Asus TF103C tablet which uses this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220106110128.66049-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some X86 tablets, which ship with Android as factory installed OS,
specify codec IRQs/GPIOS in a special Android AMCR0F28 ACPI device.
Add support for retrieving the codec IRQ from this ACPI device instead
of from the 10EC5640 device describing the codec itself and enable this
on Asus MemoPad 7 ME176C tablets.
This fixes jack-detect not working on these tablets.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220106110128.66049-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Marking the two jack gpio as static fixes the following Sparse errors:
sound/soc/intel/boards/bytcr_rt5640.c:468:26: error: symbol 'rt5640_jack_gpio' was not declared. Should it be static?
sound/soc/intel/boards/bytcr_rt5640.c:475:26: error: symbol 'rt5640_jack2_gpio' was not declared. Should it be static?
Fixes: 9ba0085668 ("ASoC: Intel: bytcr_rt5640: Add support for HP Elite Pad 1000G2 jack-detect")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210825122519.3364-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Elitepad 1000 G2 tablet has 2 headset jacks:
1. on the dock which uses the output of the codecs built-in HP-amp +
the standard IN2 input which is always used with the headset-jack.
2. on the tablet itself, this uses the line-out of the codec + an external
HP-amp, which gets enabled by the ALC5642 codec's GPIO1 pin; and IN1 for
the headset-mic.
The codec's GPIO1 is also its only IRQ output pin, so this means that
the codec's IRQ cannot be used on this tablet. Instead the jack-detect
is connected directly to GPIOs on the main SoC. The dock has a helper
chip which also detects if a headset-mic is present or not, so there
are 2 GPIOs for the jack-detect status of the dock. The tablet jack
uses a single GPIO which indicates if a jack is present or not.
Differentiating between headphones vs a headset on the tablet jack
is done by using the usual mic-bias over-current-detection mechanism.
Add support for this unique setup, this support gets enabled on this
tablet through a new BYT_RT5640_JD_HP_ELITEP_1000G2 quirk.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213415
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210819190543.784415-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to be able to do jack-detection reporting for the
mic contact on the 2nd jack found on some devices, the
DAPM topology needs to have a separate DAPM pin/input for that
microphone, instead of re-using the "Internal Mic" pin which is
normally used together with the IN1P input of the codec.
Using the "Internal Mic" dapm-pin-switch for this in a snd_soc_jack_pin to
report hotplug events causes the "Internal Mic" pin to get deactivated
when unplugging a headset from the 2nd jack, thus turning off the actual
Internal Mic (typically a pair of digital mics on devices with 2 jacks).
Fixes: 79c1123bac ("ASoC: Intel: bytcr_rt5640: Add support for a second headset mic input")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210819190543.784415-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use "cfg-lineout:2" in the components string on boards with a lineout
instead of "cfg-lineout:1", this better mirrors the speaker part of
the components string where we use "cfg-spk:1" for devices with a single
speaker and "cfg-spk:2" for stereo speakers.
The lineout is stereo by default, so using ":2" makes more sense, this
way we keep ":1" reserved in case we ever encounter a device with
a mono lineout.
We can make this change without breaking userspace because no kernel
has shipped with "cfg-lineout:1" in the component-string yet; and there
also are no userspace bits (UCM profiles) checking for this yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210816114722.107363-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ACPI-based devices, the DSDT does not include any of the
properties required by the codec driver. This is not an ACPI
limitation proper since the _DSD method could be used, as done for
Camera and SoundWire in newer platforms. For legacy devices, there is
unfortunately no other option than using a work-around: we add
properties to the codec device from the machine driver.
To avoid any issues with the codec driver being unbound, we need to
keep a reference to the codec device until the card is removed.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Elitepad 1000 G2 has 2 headset jacks:
1. on the dock which uses the output of the codecs built-in HP-amp +
the standard IN2 input which is always used with the headset-jack.
2. on the tablet itself, this uses the line-out of the codec, combined
with an external HP-amp + IN1 for the headset-mic.
Fix the HP ElitePad 1000 G2 to properly reflect this now that the
machine-driver supports this setup.
Note this also changes the mapping for the internal mic. from
IN1 (which was pointing to the 2nd headset-jack mic) to DMIC2
which is the actual input for the internal mics.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213415
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices (HP Elitepad 1000 G2) have a second headphones output
(1 on the dock, 2nd on the tablet itself) which is implemented through
the line-out output of the codec combined with an external hp-amp
which gets enabled through the codec's GPIO1 pin.
Add support for this through a new BYT_RT5640_LINEOUT_AS_HP2 quirk,
note users are expected to use this combined with the
BYT_RT5640_LINEOUT quirk. If that quirk is not set the new quirk is
ignored.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Chuwi Hi8 tablet is using an analog mic on IN1 and has its
jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
It also only has 1 speaker.
Add a quirk applying the correct settings for this configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210325221054.22714-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on which AIF is used the UCM profile needs to setup
a different path through the rt5640's "Digital Mixer Path" graph.
ATM the UCM profiles solve this by just enabling paths to the outputs /
from the input from both AIF1 and AIF2 and then relying on the DAPM
framework to power-down the parts of the graph connected to the
unused AIF.
But in order to be able to use hardware-volumecontrol and to use
the hardware mute controls, which are necessary for mute LED control,
the UCM profiles need to know which AIF is actually being used.
Add a new "aif:1" or "aif:2" part to the component string to provide
info about the used AIF to userspace / to the UCM profiles.
Note the size of byt_rt5640_components is not increased because the
size of 32 chars already is big enough.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307150503.34906-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When I added the quirk for the "HP Pavilion x2 10-p0XX" I copied the
byt_rt5640_quirk_table[] entry for the HP Pavilion x2 10-k0XX / 10-n0XX
models since these use almost the same settings.
While doing this I accidentally also copied and kept the non-standard
OVCD_TH_1500UA setting used on those models. This too low threshold is
causing headsets to often be seen as headphones (without a headset-mic)
and when correctly identified it is causing ghost play/pause
button-presses to get detected.
Correct the HP Pavilion x2 10-p0XX quirk to use the default OVCD_TH_2000UA
setting, fixing these problems.
Fixes: fbdae7d6d0 ("ASoC: Intel: bytcr_rt5640: Fix HP Pavilion x2 Detachable quirks")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210224105052.42116-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Acer One S1002 tablet is using an analog mic on IN1 and has
its jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
Note it is also using AIF2 instead of AIF1 which is somewhat unusual,
this is correctly advertised in the ACPI CHAN package, so the speakers
do work without the quirk.
Add a quirk for the mic and jack-detect settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Mele PCG03 Mini PC, being a Mini PC this device
has no speakers and no internal microphone.
To make matters worse the speaker output pins are shorted (to gnd or
to each other?) and SPKVDD is provided. So trying to output sound on the
speakers leads to shorting SPKVDD, this leads to a power dip after
which the codec is an unknown state. Sometimes it drops of the i2c
bus, sometimes it does still respond to i2c transfers, but is otherwise
not functional. TL;DR: trying to use the speaker outputs on this model
is BAD.
Besides not having speakers / an internal mic, this is a Bay Trail CR
device without a CHAN package in ACPI, so we default to SSP0-AIF2 as
codec connection. But the device is actually using SSP0-AIF1, so we
need to quirk that too.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Pavilion x2 Detachable line comes in many variants:
1. Bay Trail SoC + AXP288 PMIC, Micro-USB charging (10-k010nz, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable PC 10"
DMI_BOARD_NAME: "8021"
2. Bay Trail SoC + AXP288 PMIC, Type-C charging (10-n000nd, 10-n010nl, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "815D"
3. Cherry Trail SoC + AXP288 PMIC, Type-C charging (10-n101ng, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "813E"
4. Cherry Trail SoC + TI PMIC, Type-C charging (10-p002nd, 10-p018wm, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 Detachable 10-p0XX"
DMI_BOARD_NAME: "827C"
5. Cherry Trail SoC + TI PMIC, Type-C charging (x2-210-g2, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 210 G2"
DMI_BOARD_NAME: "82F4"
Variant 1 needs the exact same quirk as variant 2, so relax the DMI check
for the existing quirk a bit so that it matches both variant 1 and 2
(note the other variants will still not match).
Variant 2 already has an existing quirk (which now also matches variant 1)
Variant 3 uses a cx2072x codec, so is not applicable here.
Variant 4 almost works with the defaults, but it also needs a quirk to
fix jack-detection, add a new quirk for this.
Variant 5 does use a RT5640 codec (based on old dmesg output), but was
otherwise not tested, keep using the defaults for this variant.
Fixes: ec8e8418ff ("ASoC: Intel: bytcr_rt5640: Add quirks for various devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201118121515.11441-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
