The headset type detection must run to set the analogue switches
correctly for the attached headset type. Without this only headsets
with wiring matching the chip default will have a functioning mic.
commit c26a5289e8 ("ASoC: cs42l42: Add support for set_jack calls")
moved the interrupt unmasking to the component set_jack() callback.
But it's not mandatory for a machine driver to register a struct
snd_soc_jack handler. Without a registered handler the type detection
would not have run and so the mic would not work on some types of
headset.
This patch restores the unmasking of TS_PLUG and TS_UNPLUG interrupts
during probe.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-17-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver must free the IRQ in remove() to prevent the potential race
where an IRQ starts to be handled while the driver is being removed but
devres has not yet called free_irq(). However, the driver can run without
an interrupt but devm_free_irq() will hit a WARN() if no devres-managed
interrupt was ever created.
Fix this by only attempting to create the interrupt handler if the hardware
config specified an interrupt, and failing probe() if the interrupt could
not be created. This means that in cs42l42_remove() an interrupt must have
been registered if the irq number is valid and therefore it is safe to call
devm_free_irq().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-16-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling the HP or ADC by writing the corresponding PDN=0,
it takes around 20 milliseconds for it to power up and the midrail
supply to be stable. Add this wait into a DAPM widget callback.
If HP and ADC are both powering up in a DAPM sequence, there's no
need to do the wait twice. The widget will perform one wait in the
POST_PMU if there was a PRE_PMU for one or both.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-13-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't possible to switch MCLK between 12MHz and 24MHz rate groups
on-the-fly - this can only be done when cs42l42 is powered-down.
All "normal" SCLK rates use an MCLK in the 12MHz group, so change the
configs for SCLK > 12.288 MHz to use the PLL to generate an MCLK in
the 12MHz group.
As this means MCLK_DIV is always 0 it can be removed from the pll
configuration setup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently only supports configuring for sample rates <= 96k
and it isn't possible to setup a configuration that will support all
sample rates up to 192k.
For sample rates up to 96k MCLK is in the 12MHz group.
However, although 192k only requires an I2S clock in the 12MHz group,
the cs42l42 audio path is not natively 192k so the audio must be
resampled. But for 192k the SRC requires a 24MHz MCLK.
It is not possible to switch MCLK between 12MHz and 24MHz groups
on-the-fly. The 12MHz group supports all sample rates up to 96k.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.
The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 585e7079de ("ASoC: cs42l42: Add Capture Support")
Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When capture and playback substreams are both running at the same time,
cs42l42_pcm_hw_params() would be called for each direction. The first
call will configure the PLL. The second call must not write the PLL
configuration registers again if the first substream is already running,
as this could destabilize the PLL.
The DAI is marked symmetric sample bits and sample rate, so the two
directions will always have the same SCLK (I2S always has 2 channel slots
so the DAI does not need to require symmetric channels to guarantee the
same SCLK). However, since cs42l42_pll_config() is checking for an active
stream it may as well test that the requested SCLK is the same as the
currently active configuration.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several things the patch adding the support for 'I2S Reference'
got wrong:
- "None" selection is in fact equals to last selected reference
- The custom put overrides RX/TX len, TDM slot sizes, etc
- the enum is useless in most part for the reference tracking
- there is no need for EXT control as there is a single bit in
RT1011_TDM1_SET_1 register (bit 7) which selects the reference
- it was using ucontrol->value.integer.value[0] in the put/get callbacks
which causesed access to 'I2S Reference' enum with alsamixer to fail
Complements: c3de683c4d ("ASoC: rt1011: Fix 'I2S Reference' enum control caused error")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211013123300.11095-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa2 ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
Access to 'I2S Reference' enum causes alsamixer to fail to load:
$ alsamixer
cannot load mixer controls: Invalid argument
cml_rt1011_rt5682 cml_rt1011_rt5682: control 2:0:0:TL I2S Reference:0: access overflow
The reason is that the original patch adding the code was using
ucontrol->value.integer.value[0]
instead the correct
ucontrol->value.enumerated.item[0]
for an ENUM control.
Fixes: 87f40af26c ("ASoC: rt1011: add i2s reference control for rt1011")
Reported-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211011144518.2518-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98927 codec on some devices (i.e. Xiaomi Mi A2 Lite phone) requires
hardware-resetting the codec by driving a reset-gpio. This series adds
support for it through an optional reset-gpios property.
v4:
* Correctly assert/deassert the GPIO states
* Wait for the i2c port to be ready after reset
* Reset device when removed
v3:
* Fix indentation on the dev_err_probe line
v2:
* Use dev_err_probe instead of dev_err
Alejandro Tafalla (2):
ASoC: max98927: Handle reset gpio when probing i2c
dt-bindings: sound: max98927: Add reset-gpios optional property
.../devicetree/bindings/sound/max9892x.txt | 3 +++
sound/soc/codecs/max98927.c | 25 +++++++++++++++++++
sound/soc/codecs/max98927.h | 1 +
3 files changed, 29 insertions(+)
--
2.33.0
When the system plays a sound immediately after resuming from S3,
it could hear a little pop from headphones.
It is due to the HP was unmuted before the completion of
jack re-detection finished in parallel.
This patch adds a lock to make sure the HP unmute after jack detect handler,
and adds a few depop changes.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211007085519.12543-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices using the NAU8824 have only one speaker. To still have things
working properly this requires the left + right channels to both be mixed
to the left speaker output.
This mixer setup is done by userspace based on UCM profiles. But this
requires userspace to know that there is a mono-speaker. Add a helper
function (for the machine driver) to get a components string providing
this info.
This is done inside the codec driver because the codec driver already
has a DMI quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211002211459.110124-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk mechanism to allow specifying that active-high jack-detection
should be used on platforms where this info is not available in devicetree.
And add an entry for the Cyberbook T116 tablet to the DMI table, so that
jack-detection will work properly on this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211002211459.110124-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new IRQF_NO_AUTOEN flag when requesting the IRQ, rather then
disabling it immediately after requesting it.
This fixes a possible race where the IRQ might trigger between requesting
and disabling it; and this also leads to a small code cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211003132255.31743-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new IRQF_NO_AUTOEN flag when requesting the IRQ, rather then
disabling it immediately after requesting it.
This fixes a possible race where the IRQ might trigger between requesting
and disabling it; and this also leads to a small code cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211003132255.31743-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the system resumes from S3, if the system plays a beep,
there is continuous "Zizi.." noise from HP that could be heard.
It is caused by the SAR mode switch during the combo jack
re-detection which be executed parallelly in a workqueue
after the system resumes.
This patch changes the behavior of SAR mode switch to
avoid this issue.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211001074113.2223-2-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec's ASRC was enabled, the DA and AD filters use
the reference clk which tracks the I2S clks.
And if the I2S clks' timing of open and close are not expected,
this patch allows the filters to switch to use sysclk if
ASRC's ref clks disappeared and could fix the below possible issues:
1. Avoid DA filter to keep surplus samples.
2. Avoid that AD filter works failed during dapm's power on.
For example,
if I2S clks were closed before dacdat during playback off
due to jack unplug, it causes ref clks disappeared and
DA filter remained some samples which will produce pop noise
on the next HP playback.
ASRC auto-disable could clear the samples during the playback off.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211001074113.2223-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 1d25684e22 ("ASoC: nau8824: Fix open coded prefix handling")
replaced the nau8824_dapm_enable_pin() helper with direct calls to
snd_soc_dapm_enable_pin(), but the helper was using
snd_soc_dapm_force_enable_pin() and not forcing the MICBIAS + SAR
supplies on breaks headphone vs headset and button-press detection.
Replace the snd_soc_dapm_enable_pin() calls with
snd_soc_dapm_force_enable_pin() to fix this.
Cc: stable@vger.kernel.org
Fixes: 1d25684e22 ("ASoC: nau8824: Fix open coded prefix handling")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210929201512.460360-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series of patches gradually separates the ASoC specific wm_adsp
code from that required to manage firmware in Cirrus Logic DSPs.
The series starts with renaming, progresses to splitting the
functionality before finally moving the independent functionality into
drivers/firmware so that it can be used by both the existing ASoC
wm_adsp and new non-audio parts.
Charles Keepax (3):
ASoC: wm_adsp: Move check for control existence
ASoC: wm_adsp: Switch to using wm_coeff_read_ctrl for compressed
buffers
ASoC: wm_adsp: Move sys_config_size to wm_adsp
Simon Trimmer (13):
ASoC: wm_adsp: Remove use of snd_ctl_elem_type_t
ASoC: wm_adsp: Cancel ongoing work when removing controls
ASoC: wm_adsp: Rename generic DSP support
ASoC: wm_adsp: Introduce cs_dsp logging macros
ASoC: wm_adsp: Separate some ASoC and generic functions
ASoC: wm_adsp: Split DSP power operations into helper functions
ASoC: wm_adsp: Separate generic cs_dsp_coeff_ctl handling
ASoC: wm_adsp: Move check of dsp->running to better place
ASoC: wm_adsp: Pass firmware names as parameters when starting DSP
core
ASoC: wm_adsp: move firmware loading to client
ASoC: wm_adsp: Split out struct cs_dsp from struct wm_adsp
ASoC: wm_adsp: Separate wm_adsp specifics in cs_dsp_client_ops
firmware: cs_dsp: add driver to support firmware loading on Cirrus
Logic DSPs
MAINTAINERS | 11 +
drivers/firmware/Kconfig | 1 +
drivers/firmware/Makefile | 1 +
drivers/firmware/cirrus/Kconfig | 5 +
drivers/firmware/cirrus/Makefile | 3 +
drivers/firmware/cirrus/cs_dsp.c | 3109 ++++++++++++++++
include/linux/firmware/cirrus/cs_dsp.h | 242 ++
.../linux/firmware/cirrus}/wmfw.h | 8 +-
sound/soc/codecs/Kconfig | 1 +
sound/soc/codecs/cs47l15.c | 22 +-
sound/soc/codecs/cs47l24.c | 20 +-
sound/soc/codecs/cs47l35.c | 24 +-
sound/soc/codecs/cs47l85.c | 32 +-
sound/soc/codecs/cs47l90.c | 34 +-
sound/soc/codecs/cs47l92.c | 20 +-
sound/soc/codecs/madera.c | 18 +-
sound/soc/codecs/wm2200.c | 30 +-
sound/soc/codecs/wm5102.c | 16 +-
sound/soc/codecs/wm5110.c | 24 +-
sound/soc/codecs/wm_adsp.c | 3188 ++---------------
sound/soc/codecs/wm_adsp.h | 105 +-
21 files changed, 3794 insertions(+), 3120 deletions(-)
create mode 100644 drivers/firmware/cirrus/Kconfig
create mode 100644 drivers/firmware/cirrus/Makefile
create mode 100644 drivers/firmware/cirrus/cs_dsp.c
create mode 100644 include/linux/firmware/cirrus/cs_dsp.h
rename {sound/soc/codecs => include/linux/firmware/cirrus}/wmfw.h (91%)
--
2.33.0
