In current design, when the tcpm port is unregisterd, the kthread_worker
will be destroyed in the last step. Inside the kthread_destroy_worker(),
the worker will flush all the works and wait for them to end. However, if
one of the works calls hrtimer_start(), this hrtimer will be pending until
timeout even though tcpm port is removed. Once the hrtimer timeout, many
strange kernel dumps appear.
Thus, we can first complete kthread_destroy_worker(), then cancel all the
hrtimers. This will guarantee that no hrtimer is pending at the end.
Fixes: 3ed8e1c2ac ("usb: typec: tcpm: Migrate workqueue to RT priority for processing events")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20211209101507.499096-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch puts content of cdnsp_gadget_pullup function inside
spin_lock_irqsave and spin_lock_restore section.
This construction is required here to keep the data consistency,
otherwise some data can be changed e.g. from interrupt context.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reported-by: Ken (Jian) He <jianhe@ambarella.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
--
Changelog:
v2:
- added disable_irq/enable_irq as sugester by Peter Chen
drivers/usb/cdns3/cdnsp-gadget.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20211214045527.26823-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Update complete_and_exit to call kthread_exit instead of do_exit.
Change the name to reflect this change in functionality. All of the
users of complete_and_exit are causing the current kthread to exit so
this change makes it clear what is happening.
Move the implementation of kthread_complete_and_exit from
kernel/exit.c to to kernel/kthread.c. As this function is kthread
specific it makes most sense to live with the kthread functions.
There are no functional change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 Command Verifier (USB3CV) is the official tool for
USB3 Hub and Device Framework testing.
A high-speed capable device that has different device information
for full-speed and high-speed must have a Device Qualifier Descriptor.
This patch is to support device qualifier to pass
USB3CV - Chapter 9 Test [USB 2 devices] - Device Qualifier Tests.
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20211208100545.1441397-2-neal_liu@aspeedtech.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduces the Xen pvUSB frontend. With pvUSB it is possible for a Xen
domU to communicate with a USB device assigned to that domU. The
communication is all done via the pvUSB backend in a driver domain
(usually Dom0) which is owner of the physical device.
The pvUSB frontend is a USB hcd for a virtual USB host connector.
The code is taken from the pvUSB implementation in Xen done by Fujitsu
based on Linux kernel 2.6.18.
Changes from the original version are:
- port to upstream kernel
- put all code in just one source file
- move module to appropriate location in kernel tree
- adapt to Linux style guide
- minor code modifications to increase readability
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211123132048.5335-3-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys introduced a new enhancement to DWC_usb32 called Multi-Stream
Transfer (MST) to improve bulk streams performance for SuperSpeed and
SuperSpeed Plus. This enhancement allows the controller to look ahead
and process multiple bulk streams.
Previously, to initiate a bulk stream transfer, the driver has to issue
Start Transfer command and wait for the stream to complete before
initiating a new stream. As a result, the controller does not process
TRBs beyond a single stream. With the enhancement, as long as there are
new requests, the dwc3 driver can keep preparing new TRBs and the
controller can keep caching and processing them without waiting for the
transfer completion.
The programming flow is similar to regular bulk endpoint with a few
additional rules:
1) Chained TRBs of the same stream must have a matching stream ID
2) The last TRB of a stream must have CHN=0
3) All the TRBs with LST=0 must have CSP=1
Depends on the application and usage, internal tests show significant
performance improvement in UASP transfers with this enhancement.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cd9c7a8bf11f790983ac546222dd114893f16b3a.1638242424.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.16-rc5. They include:
- gadget driver fixes for reported issues
- xhci fixes for reported problems.
- config endpoint parsing fixes for where we got bitfields wrong
Most of these have been in linux-next, the remaining few were not, but
got lots of local testing in my systems and in some cloud testing
infrastructures"
* tag 'usb-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: core: config: using bit mask instead of individual bits
usb: core: config: fix validation of wMaxPacketValue entries
USB: gadget: zero allocate endpoint 0 buffers
USB: gadget: detect too-big endpoint 0 requests
xhci: avoid race between disable slot command and host runtime suspend
xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime suspending
Revert "usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default"
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf, sockmap: re-evaluate proto ops when psock is removed from
sockmap
Current release - new code bugs:
- bpf: fix bpf_check_mod_kfunc_call for built-in modules
- ice: fixes for TC classifier offloads
- vrf: don't run conntrack on vrf with !dflt qdisc
Previous releases - regressions:
- bpf: fix the off-by-two error in range markings
- seg6: fix the iif in the IPv6 socket control block
- devlink: fix netns refcount leak in devlink_nl_cmd_reload()
- dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
- dsa: mv88e6xxx: allow use of PHYs on CPU and DSA ports
Previous releases - always broken:
- ethtool: do not perform operations on net devices being
unregistered
- udp: use datalen to cap max gso segments
- ice: fix races in stats collection
- fec: only clear interrupt of handling queue in fec_enet_rx_queue()
- m_can: pci: fix incorrect reference clock rate
- m_can: disable and ignore ELO interrupt
- mvpp2: fix XDP rx queues registering
Misc:
- treewide: add missing includes masked by cgroup -> bpf.h
dependency"
* tag 'net-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (82 commits)
net: dsa: mv88e6xxx: allow use of PHYs on CPU and DSA ports
net: wwan: iosm: fixes unable to send AT command during mbim tx
net: wwan: iosm: fixes net interface nonfunctional after fw flash
net: wwan: iosm: fixes unnecessary doorbell send
net: dsa: felix: Fix memory leak in felix_setup_mmio_filtering
MAINTAINERS: s390/net: remove myself as maintainer
net/sched: fq_pie: prevent dismantle issue
net: mana: Fix memory leak in mana_hwc_create_wq
seg6: fix the iif in the IPv6 socket control block
nfp: Fix memory leak in nfp_cpp_area_cache_add()
nfc: fix potential NULL pointer deref in nfc_genl_dump_ses_done
nfc: fix segfault in nfc_genl_dump_devices_done
udp: using datalen to cap max gso segments
net: dsa: mv88e6xxx: error handling for serdes_power functions
can: kvaser_usb: get CAN clock frequency from device
can: kvaser_pciefd: kvaser_pciefd_rx_error_frame(): increase correct stats->{rx,tx}_errors counter
net: mvpp2: fix XDP rx queues registering
vmxnet3: fix minimum vectors alloc issue
net, neigh: clear whole pneigh_entry at alloc time
net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
...
This reverts commit cefdd52fa0.
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann says:
====================
bpf 2021-12-08
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 29 files changed, 659 insertions(+), 80 deletions(-).
The main changes are:
1) Fix an off-by-two error in packet range markings and also add a batch of
new tests for coverage of these corner cases, from Maxim Mikityanskiy.
2) Fix a compilation issue on MIPS JIT for R10000 CPUs, from Johan Almbladh.
3) Fix two functional regressions and a build warning related to BTF kfunc
for modules, from Kumar Kartikeya Dwivedi.
4) Fix outdated code and docs regarding BPF's migrate_disable() use on non-
PREEMPT_RT kernels, from Sebastian Andrzej Siewior.
5) Add missing includes in order to be able to detangle cgroup vs bpf header
dependencies, from Jakub Kicinski.
6) Fix regression in BPF sockmap tests caused by missing detachment of progs
from sockets when they are removed from the map, from John Fastabend.
7) Fix a missing "no previous prototype" warning in x86 JIT caused by BPF
dispatcher, from Björn Töpel.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add selftests to cover packet access corner cases
bpf: Fix the off-by-two error in range markings
treewide: Add missing includes masked by cgroup -> bpf dependency
tools/resolve_btfids: Skip unresolved symbol warning for empty BTF sets
bpf: Fix bpf_check_mod_kfunc_call for built-in modules
bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALL
mips, bpf: Fix reference to non-existing Kconfig symbol
bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
Documentation/locking/locktypes: Update migrate_disable() bits.
bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
bpf, sockmap: Attach map progs to psock early for feature probes
bpf, x86: Fix "no previous prototype" warning
====================
Link: https://lore.kernel.org/r/20211208155125.11826-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring
and there is a dereference of it in cdnsp_endpoint_init(), which could
lead to a NULL pointer dereference on failure of cdnsp_ring_alloc().
Fix this bug by adding a check of pep->ring.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@vger.kernel.org>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172700.206650-1-zhou1615@umn.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan writes:
USB-serial fixes for 5.16-rc3
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variants
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
