The new wrapper functions usb_control_msg_send/recv accept stack
variables for USB message buffers and eliminate the need of manually
allocating temporary DMA buffers. The read wrapper also treats short
reads as errors. Hence use the wrappers instead of using
usb_control_msg() directly.
Note that the conversion of f81534a_ctrl_set_register() adds an extra an
extra allocation and memcpy for every retry. Since this function is
called rarely and retries are hopefully rare, the overhead should be
acceptable.
Also note that short reads are now logged as -EREMOTEIO instead of
indicating the amount of data read.
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Link: https://lore.kernel.org/r/20210801203122.3515-4-himadrispandya@gmail.com
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
User space can keep a tty open indefinitely and that should not prevent
a hung up port and its USB device from being runtime suspended.
Fix this by incrementing the PM usage counter when the port it activated
and decrementing the counter when the port is shutdown rather than when
the tty is installed and the last reference is dropped, respectively.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the core error labels by consistently naming them after what
they do rather than after from where they are jumped to.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
0xac24 device ID is already defined and used via
BANDB_DEVICE_ID_USO9ML2_4. Remove the duplicate from the list.
Fixes: 27f1281d5f ("USB: serial: Extra device/vendor ID for mos7840 driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Johan writes:
USB-serial fix for 5.15-rc1
Here's a single fix for a pl2303 type detection regression, and which
has been in linux-next over night.
* tag 'usb-serial-5.15-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: fix GL type detection
Johan writes:
USB-serial updates for 5.15-rc1
Here are the USB serial updates for 5.15-rc1, including:
- a couple of fixes for cp210x termios error handling
- retrieval of fw revisions for more cp210x types
- a switch to octal permissions for all module-parameter definitions
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.15-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: replace symbolic permissions by octal permissions
USB: serial: cp210x: determine fw version for CP2105 and CP2108
USB: serial: cp210x: clean up type detection
USB: serial: cp210x: clean up set-chars request
USB: serial: cp210x: clean up control-request timeout
USB: serial: cp210x: fix flow-control error handling
USB: serial: cp210x: fix control-characters error handling
USB: serial: io_edgeport: drop unused descriptor helper
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
Replace symbolic permission macros with octal permission numbers
because octal permission numbers are easier to read and understand
instead of their symbolic macro names.
No functional change.
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Utkarsh Verma <utkarshverma294@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2105, CP2108 and CP2102N have vendor requests that can be used to
retrieve the firmware version. Having this information available is
essential when trying to work around buggy firmware as a recent CP2102N
regression showed.
Determine and log the firmware version also for CP2105 and CP2108
during type detection at probe.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up attach somewhat by moving type detection into the quirk helper
and giving it a more generic name.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the generic control request helper to implement the SET_CHARS
request.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
For consistency use the USB_CTRL_GET_TIMEOUT define for the
read-register request timeout (same value as USB_CTRL_SET_TIMEOUT).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the driver crtscts state is not updated in the unlikely
event that the flow-control request fails. Not doing so could break RTS
control.
Fixes: 5951b85088 ("USB: serial: cp210x: suppress modem-control errors")
Cc: stable@vger.kernel.org # 5.11
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In the unlikely event that setting the software flow-control characters
fails the other flow-control settings should still be updated (just like
all other terminal settings).
Move out the error message printed by the set_chars() helper to make it
more obvious that this is intentional.
Fixes: 7748feffcd ("USB: serial: cp210x: add support for software flow control")
Cc: stable@vger.kernel.org # 5.11
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Johan writes:
USB-serial updates for 5.14-rc1
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add support for GPIOs on CP2108
USB: serial: drop irq-flags initialisations
USB: serial: mos7840: drop buffer-callback return-value comments
USB: serial: mos7720: drop buffer-callback sanity checks
USB: serial: io_edgeport: drop buffer-callback sanity checks
USB: serial: digi_acceleport: add chars_in_buffer locking
USB: serial: digi_acceleport: reduce chars_in_buffer over-reporting
USB: serial: make usb_serial_driver::chars_in_buffer return uint
USB: serial: make usb_serial_driver::write_room return uint
Similar to some other CP210x device types, CP2108 has a number of GPIO
pins that can be exposed through gpiolib.
CP2108 has four serial interfaces but only one set of GPIO pins, which
is modelled as a single gpio chip and registered as a child of the first
interface.
CP2108 has 16 GPIOs so the width of the state variables needs to be
extended to 16 bits and this is also reflected in the control requests.
Like CP2104, CP2108 have GPIO pins with configurable alternate
functions and pins unavailable for GPIO use are determined and reported
to gpiolib at probe.
Signed-off-by: Pho Tran <pho.tran@silabs.com>
Co-developed-by: Tung Pham <tung.pham@silabs.com>
Signed-off-by: Tung Pham <tung.pham@silabs.com>
[ johan: rewrite gpio get() and set(); misc cleanups; amend commit
message ]
Link: https://lore.kernel.org/r/20210610132844.25495-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Make data_bits what it really is. Assign proper bit counts to data_bits
instead of magic 0..3. There are two reasons:
1) it's clear what we store there, and
2) it will make the transition to tty_tty_get_char_size() in the next
patch easier.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c9 ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
With the inclusion of Omni 56K Plus, this driver seem to be more common
among the family of Zyxel omni modem. Update the driver and module
descriptions.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Zyxel Omni 56K Plus modem, this modem include:
USB chip:
NetChip
NET2888
Main chip:
901041A
F721501APGF
Another modem using the same chips is the Zyxel Omni 56K DUO/NEO,
could be added with the right USB ID.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the three requests which erroneously used usb_rcvctrlpipe().
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from the three drivers that got this
wrong.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called with a NULL port
driver-data pointer or if some other always-true sanity checks failed.
The bogus sanity checks were later removed by commit ce039bd4b2 ("USB:
serial: mos7840: drop paranoid port checks") and 7b2faede67 ("USB:
serial: mos7840: drop port driver data accessors") but the
function-header comments were never updated to match.
Drop the outdated return-value comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
