Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch e60c2991f1 make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.
Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.
Fixes: e60c2991f1 ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For years we've been carrying legacy omap-serial in addition to
8250_omap driver and 8250_omap should be used instead.
Let's finally start planning on removing omap-serial by first not
building it if 8250_omap is selected to save some memory.
The defconfigs have switched over to using 8250_omap, and we have
a fixup in place for the the serial console since commit 00648d0282
("tty: serial: 8250: omap: add ttySx console if the user didn't").
So people updating their systems without omap-serial will see
boot time warnings on what is going on.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to remove the use of pm_runtime_irq_safe() from serial drivers
to allow making PM runtime handling generic. Let's simplify things by
disabling PM runtime autoidle for omap-serial as this driver has been
deprecated for years because of the 8250_omap driver.
There are still some omap-serial users that seem to hang on to it for
some unknown rs485 reasons it seems. But presumably those folks do not
need PM runtime autoidle with omap-serial, and hopefully can just move
to using 8250_omap driver instead.
For 8250_omap driver, we will eventually move to use generic serial
layer PM based on patches done by Andy Shevchenko to remove
pm_runtime_irq_safe() usage.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to further reduce the scope of ndo_do_ioctl(), move
out the SIOCWANDEV handling into a new network device operation
function.
Adjust the prototype to only pass the if_settings sub-structure
in place of the ifreq, and remove the redundant 'cmd' argument
in the process.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Jan \"Yenya\" Kasprzak" <kas@fi.muni.cz>
Cc: Kevin Curtis <kevin.curtis@farsite.co.uk>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-x25@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Add back an irqrestore-version of the sysrq port-unlock helper and use
it in the 8250 callbacks that need it.
Fixes: 75f4e830fa ("serial: do not restore interrupt state in sysrq helper")
Cc: stable@vger.kernel.org # 5.13
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210714080427.28164-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->port is already set when rs_open is called given we linked it by
tty_port_link_device(). If it wasn't, the tty layer would WARN loudly.
So it's pointless to set it in rs_open. Instead, use the value in
tty->port to find out the serial_state (info).
It's a fallout of commit b19e2ca77e (TTY: use tty_port_link_device)
which added tty_port_link_device here, but omitted to remove the
tty->port assignment from rs_open.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a print of serial_name and serial_version from the probe
function, i.e. show_serial_version() from amiga_serial_probe(). The
value of such a print is minimal.
Aside from that, the version is artificial (copied from the serial core
in 2.3.45pre2 and never increased). So inline the version into
seq_printf's format string in rs_proc_show() and remove both strings
completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.
If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.
To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.
Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is used for TX and RX by serial driver, it should
pass the DMA device pointer to DMA API instead of UART device
pointer. DMA device should be used for DMA API because only
the DMA device is aware of how the device connects to the memory.
There might be an extra level of address translation due to a
SMMU attached to the DMA device. When serial device is used for
DMA API, the DMA API will have no clue of the SMMU attached to
the DMA device.
This patch is necessary to fix the SMMU page faults
which is observed when a DMA(with SMMU enabled) is attached
to UART for transfer.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Link: https://lore.kernel.org/r/20210629045902.48912-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make pl011 work better, multiple interrupts are
required, such as TXIM, RXIM, RTIM, error interrupt(FE/PE/BE/OE);
at the same time, pl011 to GIC does not merge the interrupt
lines(each serial-interrupt corresponding to different GIC hardware
interrupt), so need to enable and request multiple gic interrupt
numbers in the driver.
Signed-off-by: Bing Fan <tombinfan@tencent.com>
Link: https://lore.kernel.org/r/1625103512-30182-1-git-send-email-hptsfb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic support for RS485: Provide a callback to configure RS485
settings. Handle the RS485 specific part in the functions
pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic
start/stop callbacks.
Beside via IOCTL from userspace RS485 can be enabled by means of the
device tree property "rs485-enabled-at-boot-time".
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20210630225644.3744-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report extra baud rates supported above the base rate for ports with the
UPF_MAGIC_MULTIPLIER property, so that people have a way to find out
that they can be used with their system, e.g.:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
serial8250.0: ttyS0 extra baud rates supported: 230400, 460800
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS1 extra baud rates supported: 230400, 460800
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Otherwise there is no clear way to figure this out, as the feature is
only reported as an obscure TTY flag in bit 16:
$ cat /sys/class/tty/ttyS[0-2]/flags
0x10010040
0x10010040
0x90000040
$
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260334170.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
