Variable negative is being assigned a value that is never read, it is
being re-assigned later. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/staging/iio/resolver/ad2s1210.c:502:3: warning: Value stored
to 'negative' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220418134603.81336-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This functionality is intended to allow for a few temperature
sensors to be missing (and hence not worth reading) on the final
device in a chain. The ones removed are 3 and 5 (unlike for
the ADC channels where it is 4 and 5).
The datasheet includes a foot note 3 to Table 12 that makes this complex
to support.
"(3) To remove AUX5 or AUX5 and AUX3 from the alert detection, conversions
on three auxiliary ADC input channels only must be selected in the
control register."
This mode has never been supported by the driver.
As this support would be complex to add and the rework is being done
against a QEMU model developed for the purposes of verifying nothing
is broken, it is better to drop this support for now.
Reported-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-16-jic23@kernel.org
This driver had a slightly non standard events ABI but there seems
to be no reason for not doing it with the core support for rising and
falling events on the two types of channels.
In theory the events on different daisy chained chips could be at
different levels, but the driver has never supported this and it doesn't
seem likely to be used so let us ignore that option.
Includes reordering so that we only set the software cached value
of the thresholds if the hardware write succeeds.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-7-jic23@kernel.org
1. Postfix register addresses with _REG to distinguish them from
fields within the registers
2. Switch to using FIELD_PREP and masks to aid readability.
3. Shorten a few defines to make the lines remain a sensible length.
4. Fix an issue whether where an CTRL_LB field is set in CTRL_HB.
5. Fix wrong AUX1_3_4 which should be AUX_1_3_5 according to
table 14 in the datasheet.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-3-jic23@kernel.org
The bit reversal was wrong for bits 1 and 3 of the 5 bits.
Result is driver failure to probe if you have more than 2 daisy-chained
devices. Discovered via QEMU based device emulation.
Fixes tag is for when this moved from a macro to a function, but it
was broken before that.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 065a7c0b1f ("Staging: iio: adc: ad7280a.c: Fixed Macro argument reuse")
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-2-jic23@kernel.org
This change does a conversion of the driver to use device-managed init
functions. The 2 regulators and the clock inits are converted to use
devm_add_action_or_reset() callbacks for de-initializing them when the
driver unloads.
And finally the devm_iio_device_register() function can be use to register
the device.
The remove hook can finally be removed and the spi_set_drvdata() call can
also be removed as the private data is no longer used.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115209.300665-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
1st set of new IIO/counter device support, features and cleanup for 5.14
There are a couple of large cleanup sets in here alongside a number of new
drivers.
Note an immutable branch merged to add a stub for i2c_verify_client()
as needed to avoid a build issue in the fxls8962af driver as a result of a
workaround for a device errata that only applies when i2c interface is used.
Counters
========
New device support
* intel,quadrature encoder peripheral found on Elkhart Lake platforms.
- New driver.
IIO
===
New device support
* amstaos,tsl2591 ambient light sensor.
- New driver + bindings
- Follow up fix to ensure some local variables are suitable for error
handling.
* fsl,fxls8962af + fsl,fxls8964af accelerometers
- New driver + bindings
- Includes an errata work around that cause a build bot failure fixed
by adding a stub to i2c.
* kionix,kxcjk-1013
- Add support for KX023-1025 device. Mostly a different register map
that needed to be supported.
* murata,sca3300 accelerometer
- New driver + bindings
* st,lsm9ds0 IMU
- Rework of st,sensors driver to cleanly support this new glue driver
that enables the two parts of the LSM9DS0.
* ti,tsc2046 touchscreen controller ADC.
- New driver. Intent here is to use this with existing IIO consumer
drivers such as resistive-adc-touch.
- Follow up fix to avoid an issue with unsigned subtraction in error
check.
* ti,tmp117 digital temperature sensor
- New driver + bindings
Features
* adi,ad5755
- Add missing dt-binding doc
* adi,ad7298
- Add ACPI ID used on Intel Galileo Gen 1 boards.
- Add missing dt-binding doc
* adi,ad7476
- Add missing dt-binding doc
* adi,ad7746
- Add missing dt-binding doc for this driver that will hopefully move out
of staging shortly. Update staging driver to use the binding instead of
platform data.
* adi,adis16201 + adis16209
- Add missing dt-binding doc
* adi,adis16480
- Support burst mode for adis16495 and adis16497 parts.
* bosch,bma220
- Add missing dt-binding doc
* fsl,mma7455
- Add missing dt-binding doc
* iio-rescale
- Support handling of processed channels from provider. Some ADCs
require (typically non linear) calibration functions to be applied,
and so provide only IIO_CHAN_INFO_PROCESSED read back. They can be
used as providers to the iio-rescale driver which needs to handle them
somewhat differently from IIO_CHAN_INFO_RAW
* sensiron,sps30
- Support the serial interface. Note this required significant
refactoring of existing driver.
* st,st-sensors
- Add mount matrix support for normal dt-binding whilst continuing to
support the odd ACPI approach for accelerometers.
* ti,dac082s085 + similar
- Add missing dt-binding doc
* trivial-devices - add entries for
- memsic,mx4005, memsic,mx6255 and memsic,mxc6655
- sensortek,stk8312 and sensortek,stk8ba50
Cleanup / minor fixes
* core
- Use devm_add_action_or_reset() to replace boilerplate in several
driver and core IIO devm_* functions.
- Fix an error path issue introduced by above, that could return an
error pointer rather than the expected null from dev_iio_device_alloc()
- Move more IIO internals related fields from struct iio_dev to
struct iio_dev_opaque.
- Drop unused final update of in_loc in demux setup.
* Docs
- Move some docs from driver specific to core dos to avoid replication
of names which the documentation builder does not allow.
Note this means adding a few device specific notes to the general docs
to cover the more unusual uses of the ABI.
- ABI: Move old buffer/* and scan_elements/* docs to obsolete as now we
have the bufferX/* variant. Not we are not getting rid of these
interfaces, just encouraging new code to use the new interface.
* IIO wide:
- Tidy up new cases of dev.parent etc being set in drivers as the core
now does it.
- Fix more cases of possible miss-aligned buffers when passed to
iio_push_to_buffers_with_timestamp(). Note we only have one known
instance of anyone seeing this bug actually happening, so this has been
a low priority cleanup effort for several cycles.
- sysfs_emit() used in more drivers.
- Runtime pm tidy up and use of pm_runtime_resume_and_get()
- Buffer alignment fixes as iio_push_to_buffers_with_timestamp requires
that the timestamp when inserted by naturally aligned + consumers can
assume that all fields are naturally aligned. Part of a long running
effort, with at least 2 more series to come tackling additional
variants.
- Stop specifying "mount-matrix" property name in every lookup of the
mount matrix from firmware by hard coding it in the core.
* adi,ad7476
- Handle the variety of different regulators used by the parts supported
by this driver (came up in dt-binding review)
* adi,ad7746
- Trivial drop of if (ret) return ret; return 0; pattern
- Tidy up comments
- Pull capdac setup out to own function.
* adi,ad7766
- Trivial drop of if (ret) return ret; return 0; pattern
* adi,adis
- Avoid returning error codes in interrupt handlers.
- Handle a failure in spi_write in the trigger handler.
- Rework to add updating of device page after changing it.
- Don't push data to IIO buffers when read failed.
- Add configuration of burst max speed to core avoid handling this in
each driver.
- Use the adis_dev_lock() helper in adis16260 and adis16136 drivers.
- Excessive includes cleanup via include-what-you-use static checker
after zero day highlighted that these needed updating.
* afe
- Amend binding to add #io-channel-cells, thus allowing this IIO
consumer to also be an IIO provider.
* aosong,am2315
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* bosch,bma180
- Adding missing bandwidth settings (500, 1000 Hz)
* bosch,bme680
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* ep93xx_adc,
- Drop a redundant error print.
* maxim,max118
- Convert remainder of probe() to devm_ managed functions.
- Avoid some repeated jumping back and forth between iio_dev and
spi structures.
* maxim,max11100
- Use get_unaligned_be16() instead of open coding.
- Convert remainder of probe() to devm_ managed functions.
* samsung,exynos_adc
- Unused error value dropped.
* sensiron,sgp30
- Drop use of %hx in favor of %x and letting the normal type conversion
work.
* sensortek,stk8312
- Add lowercase device id and note uppercase version deprecated.
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* sprx,sc72xx_adc
- add MODULE_DEVICE_TABLE
* st,lsm6dsx
- Fix docs of valid ODRs
* st,sensors
- dt-binding rework. Two efforts on this crossed in a previous cycle
so this update cherry picks the best of the two yaml conversions.
- Don't copy the channel spec array as now ext_info is no longer modified.
* st,stm32-adc
- tidy up some docs that were marked as kernel-doc but aren't.
* ti,adc081c, ti,adc0832, ti,adc108s102 and ti,adc161s626
- Convert remainder of probe() functions to devm_ managed functions
to simplify error handing and remove paths.
* tag 'iio-for-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (171 commits)
i2c: core: Add stub for i2c_verify_client() if !CONFIG_I2C
iio: adis: Cleanout unused headers
iio: accel: bma180: Add missing 500 Hz / 1000 Hz bandwidth
counter: Add support for Intel Quadrature Encoder Peripheral
staging: iio: cdc: ad7746: extract capac setup to own function
staging: iio: cdc: ad7746: clean up probe return
staging: iio: cdc: ad7746: remove ordinary comments
iio: adc: ti-adc161s626: Use devm managed functions for all of probe.
iio: adc: ti-adc108s102: Use devm managed functions for all of probe()
iio: adc: ti-adc0832: Use devm managed functions for all of probe()
iio: adc: ti-adc081c: Use devm managed functions for all of probe()
iio: adc: max1118: Avoid jumping back and forth between spi and iio structures
iio: adc: max1118: Use devm_ managed functions for all of probe
iio: adc: max11100: Use devm_ functions for rest of probe()
iio: adc: max11100: Use get_unaligned_be16() rather than opencoding.
iio: chemical: sgp30: Drop use of %hx in format string.
iio: gyro: st_gyro: Support mount matrix
iio: magnetometer: st_magn: Support mount matrix
iio: accel: st_sensors: Stop copying channels
iio: accel: st_sensors: Support generic mounting matrix
...
0-day recently added the include-what-you-use header checker and
it gave a warning on an adis patch. As such I decided to
run it on all the adis drivers and see if it made sensible suggestions.
Note this doesn't represent a complete list of what it suggested changing
as I filtered out a few on the basis they are standard headers used to
effectively include a bunch of other headers.
Could split this into a patch per driver if people prefer.
Note to anyone else trying this tool is that it is somewhat
of a loose cannon so you will be wanting to carefully check any
suggestions before proposing patches!
I thought about also reorganising the headers whilst here, but
that would make this patch harder to read, or lead to another rather
noisy patch across most of the files.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210603193616.3708447-1-jic23@kernel.org
AD7745 devices don't have the CIN2 pins and therefore can't handle related
channels. Forcing the number of AD7746 channels may lead to enabling more
channels than what the hardware actually supports.
Avoid num_channels being overwritten after first assignment.
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Fixes: 83e416f458 ("staging: iio: adc: Replace, rewrite ad7745 from scratch.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
This capacitance to digital converter (CDC) driver is compliant with
the IIO ABI. Note, not all features supported (e.g. window event modes)
but the driver should be in a useful functional state.
The cleanup was done against QEMU emulation of the device rather than
actual hardware. Whilst this was a bit of an experiment, it made it
easy to confirm that the driver remained in a consistent working state
through the various refactors. If it worked in the first place, it
should still be working after this cleanup.
Given some IIO drivers require expensive hardware setups, (not particularly
true with this one) the use of QEMU may provide a viable way forward
for providing testing during code changes where previously we'd had
to rely on sharp eyes and crossed fingers.
Note, no explicit MAINTAINERS entry as it will be covered by the
generic catch-alls for ADI and IIO drivers which are sufficient.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-25-jic23@kernel.org
Every other register related to raw value on the datasheet is
described as correpsonding to the 12MSB of the actual
data registers + the bottom 4 bits are 0. So lets treat this
as what it actually is, which is a 12 bit value.
Note that we will have to be a little careful to compensate for
the offset and scale values.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-18-jic23@kernel.org
Note this doesn't support everything the chip can do as we ignore
window mode for now (in window / out of window).
* Given the chip doesn't have any way of disabling the threshold
pins, use disable_irq() etc to mask them except when we actually
want them enabled (previously events were always enabled).
Note there are race conditions, but using the current state from
the status register and disabling interrupts across changes in
type of event should mean those races result in interrupts,
but no events to userspace.
* Correctly reflect that there is one threshold line per channel.
* Only take notice of rising edge. If anyone wants the other edge
then they should set the other threshold (they are available for
rising and falling directions). This isn't perfect but it makes
it a lot simpler.
* If insufficient interrupts are specified in firnware, don't support
events.
* Adaptive events use the same pos/neg values of thrMD as non adaptive
ones.
Tested against qemu based emulation.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210314181511.531414-13-jic23@kernel.org
The event line is active high and not maskable within the device.
It indicates current state directly.
The device supports separate rising and falling thresholds so rather
than trying to using each bound to detect in both directions just use
IRQF_TRIGGER_RISING. If a user wants to detect the value falling
back below the threshold, then set the falling threshold appropriately.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-8-jic23@kernel.org
