Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
Pull regulator updates from Mark Brown:
"Quite a quiet release for the regulator API, mainly a few new drivers
plus a lot of fixes for the Raspberry Pi panel driver.
There's also a SPI commit in here which I managed to apply to the
wrong tree and then didn't notice until there were too many commits on
top of it, sorry about that.
- Make it easier to use the virtual consumer test driver with DT
systems.
- Substantial overhaul providing various fixes and robustness
improvements for the Raspberry Pi panel driver.
- Support for Qualcomm PMX65 and SDX65, Richtek RT5190A, and Texas
Instruments TPS62864x"
* tag 'regulator-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (26 commits)
regulator: qcom-rpmh: Add support for SDX65
regulator: dt-bindings: Add PMX65 compatibles
regulator: vctrl: Use min() instead of doing it manually
regulator: rt5190a: Add support for Richtek RT5190A PMIC
regulator: Add bindings for Richtek RT5190A PMIC
regulator: Convert TPS62360 binding to json-schema
regulator: cleanup comments
regulator: virtual: add devicetree support
regulator: virtual: warn against production use
regulator: virtual: use dev_err_probe()
regulator: tps62864: Fix bindings for SW property
regulator: Add support for TPS6286x
regulator: Add bindings for TPS62864x
regulator/rpi-panel-attiny: Use two transactions for I2C read
regulator/rpi-panel-attiny: Use the regmap cache
regulator: rpi-panel: Remove get_brightness hook
regulator: rpi-panel: Add GPIO control for panel and touch resets
regulator: rpi-panel: Convert to drive lines directly
regulator: rpi-panel: Ensure the backlight is off during probe.
regulator: rpi-panel: Serialise operations.
...
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While computing sgs in spi_map_buf(), the data type
used in min_t() for max_seg_size is 'unsigned int' where
as that of ctlr->max_dma_len is 'size_t'.
min_t(unsigned int,x,y) gives wrong results if one of x/y is
'size_t'
Consider the below examples on a 64-bit machine (ie size_t is
64-bits, and unsigned int is 32-bit).
case 1) min_t(unsigned int, 5, 0x100000001);
case 2) min_t(size_t, 5, 0x100000001);
Case 1 returns '1', where as case 2 returns '5'. As you can see
the result from case 1 is wrong.
This patch fixes the above issue by using the data type of the
parameters that are used in min_t with maximum data length.
Fixes: commit 1a4e53d2fc ("spi: Fix invalid sgs value")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220316175317.465-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi fix from Mark Brown:
"One fix for type conversion issues when working out maximum
scatter/gather segment sizes.
It caused problems for some systems where the limits overflow
due to the type conversion"
* tag 'spi-fix-v5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Fix invalid sgs value
Merge series from Alim Akhtar:
This series adds support for the SPI controller in the Tesla FSD SoC,
also pulling in:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-spi-dt-v5.18
from the MFD tree which has dependencies for the DT bindings.
Merge series from Krishna Yarlagadda <kyarlagadda@nvidia.com>:
Add ACPI support for Tegra210 QUAD SPI driver Support new Tegra194
feature, combined sequence mode.
Commit d40f0b6f2e instroduced last_cs_enable to avoid setting
chipselect if it's not necessary, but it also introduces a bug. The
chipselect may not be set correctly on multi-device SPI busses. The
reason is that we can't judge the chipselect by bool last_cs_enable,
since chipselect may be modified after other devices were accessed.
So we should record the specific state of chipselect in case of
confusion.
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Link: https://lore.kernel.org/r/20220217141234.72737-1-yun.zhou@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi fixes from Mark Brown:
"A few small driver specific fixes"
* tag 'spi-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: rockchip: terminate dma transmission when slave abort
spi: rockchip: Fix error in getting num-cs property
spi: spi-zynq-qspi: Fix a NULL pointer dereference in zynq_qspi_exec_mem_op()
