This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly
found on Xilinx FPGAs. At the moment clock control is very basic: we
just enable the clock during probe and pin the frequency. In the future,
someone could add support for disabling the clock when not in use.
Some common code has been specially demarcated. While currently only
used by the PWM driver, it is anticipated that it may be split off in
the future to be used by the timer driver as well.
This driver was written with reference to Xilinx DS764 for v1.03.a [1].
[1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are no arm64 specific constructs in this driver and it compiles
just fine with ARCH=arm.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull pwm updates from Thierry Reding:
"This adds support for the PWM controller found on Toshiba Visconti
SoCs and converts a couple of drivers to the atomic API.
There's also a bunch of cleanups and minor fixes across the board"
* tag 'pwm/for-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (35 commits)
pwm: Reword docs about pwm_apply_state()
pwm: atmel: Improve duty cycle calculation in .apply()
pwm: atmel: Fix duty cycle calculation in .get_state()
pwm: visconti: Add Toshiba Visconti SoC PWM support
dt-bindings: pwm: Add bindings for Toshiba Visconti PWM Controller
arm64: dts: rockchip: Remove clock-names from PWM nodes
ARM: dts: rockchip: Remove clock-names from PWM nodes
dt-bindings: pwm: rockchip: Add more compatible strings
dt-bindings: pwm: Convert pwm-rockchip.txt to YAML
pwm: mediatek: Remove unused function
pwm: pca9685: Improve runtime PM behavior
pwm: pca9685: Support hardware readout
pwm: pca9685: Switch to atomic API
pwm: lpss: Don't modify HW state in .remove callback
pwm: sti: Free resources only after pwmchip_remove()
pwm: sti: Don't modify HW state in .remove callback
pwm: lpc3200: Don't modify HW state in .remove callback
pwm: lpc18xx-sct: Free resources only after pwmchip_remove()
pwm: bcm-kona: Don't modify HW state in .remove callback
pwm: bcm2835: Free resources only after pwmchip_remove()
...
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
Add driver for the PWM controller on Toshiba Visconti ARM SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: fix up a couple of checkpatch warnings]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Adds support to control the PWM bus available in official Raspberry Pi
PoE HAT. Only RPi's co-processor has access to it, so commands have to
be sent through RPi's firmware mailbox interface.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
The Netronix EC provides a PWM output which is used for the backlight
on some ebook readers. This patches adds a driver for the PWM output.
The .get_state callback is not implemented, because the PWM state can't
be read back from the hardware.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Lightning Mountain(LGM) SoC contains a PWM fan controller. This
PWM controller does not have any other consumer, it is a dedicated PWM
controller for fan attached to the system. Add driver for this PWM fan
controller.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Introduce driver for Synopsys DesignWare PWM Controller used on Intel
Elkhart Lake.
Initial implementation is done by Felipe Balbi while he was working at
Intel with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Add support for the PWM controller of the sl28cpld board management
controller. This is part of a multi-function device driver.
The controller has one PWM channel and can just generate four distinct
frequencies.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The unicore32 port is removed from the kernel.
There is no point to keep stale PWM driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Depending on MACH_INGENIC prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch adds support for the Azoteq IQS620A, capable of generating
a 1-kHz PWM output with duty cycle between ~0.4% and 100% (inclusive).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The TCU registers are shared between a handful of drivers, accessing
them through the same regmap.
While this driver is devicetree-compatible, it is never (as of now)
probed from devicetree, so this change does not introduce a ABI problem
with current devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ingenic-timer "TCU" driver provides us with clocks, that can be
(un)gated, reparented or reclocked from devicetree, instead of having
these settings hardcoded in this driver.
The new code now uses a clk pointer per PWM (instead of a clk per
pwm-chip before). So the pointer is stored in per-pwm data now.
The calls to arch-specific timer code is replaced with standard
clock API calls to start and stop each channel's clock.
While this driver is devicetree-compatible, it is never (as of now)
probed from devicetree, so this change does not introduce a ABI problem
with current devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are some expectations which the callbacks provided by lowlevel
drivers should fulfill. Implement checks that help driver authors to get
these semantics right. As these have some overhead the checks can be
disabled using a Kconfig setting.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The dependency on OMAP_DM_TIMER is only a runtime dependency. Also
OMAP_DM_TIMER cannot be enabled without ARCH_OMAP being enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The TI PWMSS driver is a simple bus driver for providing power
power management for the PWM peripherals on TI AM33xx SoCs, namely
eCAP, eHRPWM and eQEP. The eQEP is a counter rather than a PWM, so
it does not make sense to have the bus driver in the PWM subsystem
since the PWMSS is not exclusive to PWM devices.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
Pull pwm updates from Thierry Reding:
"This set of changes contains a new driver for SiFive SoCs as well as
enhancements to the core (device links are used to track dependencies
between PWM providers and consumers, support for PWM controllers via
ACPI, sysfs will now suspend/resume PWMs that it has claimed) and
various existing drivers"
* tag 'pwm/for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: fsl-ftm: Make sure to unlock mutex on failure
pwm: fsl-ftm: Use write protection for prescaler & polarity
pwm: fsl-ftm: More relaxed permissions for updating period
pwm: atmel-hlcdc: Add compatible for SAM9X60 HLCDC's PWM
pwm: bcm2835: Improve precision of PWM
leds: pwm: Support ACPI via firmware-node framework
pwm: Add support referencing PWMs from ACPI
pwm: rcar: Remove suspend/resume support
pwm: sysfs: Add suspend/resume support
pwm: Add power management descriptions
pwm: meson: Add documentation to the driver
pwm: meson: Add support PWM_POLARITY_INVERSED when disabling
pwm: meson: Don't cache struct pwm_state internally
pwm: meson: Read the full hardware state in meson_pwm_get_state()
pwm: meson: Simplify the calculation of the pre-divider and count
pwm: meson: Move pwm_set_chip_data() to meson_pwm_request()
pwm: meson: Add the per-channel register offsets and bits in a struct
pwm: meson: Add the meson_pwm_channel data to struct meson_pwm
pwm: meson: Pass struct pwm_device to meson_pwm_calc()
pwm: meson: Don't duplicate the polarity internally
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX7ULP has TPM(Low Power Timer/Pulse Width Modulation Module) inside,
it can support multiple PWM channels, all the channels share same
counter and period setting, but each channel can configure its duty and
polarity independently.
There are several TPM modules in i.MX7ULP, the number of channels in TPM
modules are different, it can be read from each TPM module's PARAM
register.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
K3 devices have the same EHRPWM IP as OMAP SoCs. Enable the driver to be
built for K3 devices. Also, drop reference to AM33xx in help text, as IP
is found on multiple TI SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The two PWM implementations called v1 (for i.MX1 and i.MX21) and v2 (for
i.MX27 and later) have nothing in common apart from needing two clocks
named "per" and "ipg" and being integrated in a SoC named i.MX.
So split the file containing the two disjunct drivers into two files and
two complete separate drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: fix a modular build issue]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
K3 devices have the same ECAP IP as OMAP SoCs. Enable driver to be built
for K3 devices. Also, drop reference to AM33xx in help text, as IP is
found on multiple TI SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for MT7628. The SoC is legacy MIPS and hence has no complex
clock tree. This patch add an extra flag to the SoC specific data
indicating, that no clocks are present.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When compile-testing the PWM driver without also enabling the
stm32_timers MFD, we run into a link error:
drivers/pwm/pwm-stm32.o: In function `stm32_pwm_raw_capture.isra.6':
pwm-stm32.c:(.text+0xcb0): undefined reference to `stm32_timers_dma_burst_read'
We don't need the '|| COMPILE_TEST' here, since stm32_timers itself
can be built with CONFIG_COMPILE_TEST on all architectures, so we do
get the coverage through allmodconfig and randconfig builds even
when we make it a hard dependency.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull pwm updates from Thierry Reding:
"This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups all
across the board"
* tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (29 commits)
pwm: rcar: Add suspend/resume support
pwm: rcar: Use PM Runtime to control module clock
dt-bindings: pwm: rcar: Add bindings for R-Car M3N support
pwm: rcar: Fix a condition to prevent mismatch value setting to duty
pwm: sysfs: Use put_device() instead of kfree()
dt-bindings: pwm: sunxi: Add new compatible strings
pwm: sun4i: Simplify controller mapping
pwm: sun4i: Drop unused .has_rdy member
pwm: sun4i: Properly check current state
pwm: Remove depends on AVR32
pwm: stm32: LPTimer: Use 3 cells ->of_xlate()
dt-bindings: pwm-stm32-lp: Add #pwm-cells
pwm: stm32: Protect common prescaler for all channels
pwm: stm32: Remove unused struct device
pwm: mediatek: Improve precision in rate calculation
pwm: mediatek: Remove redundant MODULE_ALIAS entries
pwm: mediatek: Fix up PWM4 and PWM5 malfunction on MT7623
pwm: jz4740: Enable for all Ingenic SoCs
pwm: jz4740: Add support for devicetree
pwm: jz4740: Implement ->set_polarity()
...
This driver works perfectly with all the versions of the SoCs from
Ingenic that are supported upstream.
This makes the driver usable on JZ4740, JZ4770 and JZ4780 SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
