Since recently, the kernel is nagging about mutable irq_chips:
[ 4.967050] gpio gpiochip1: (e2004190.gpio-input): not an immutable chip, please consider fixing it!
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220428111622.1395831-1-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a derivative
of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in the
Renesas drivers. Mainly sharing similar data between the different
SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880"
* tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (188 commits)
pinctrl: mediatek: common-v1: fix semicolon.cocci warnings
pinctrl: nuvoton: wpcm450: Fix build error without OF
pinctrl: qcom-pmic-gpio: Add support for pm8450
dt-bindings: pinctrl: aspeed: Update gfx node in example
dt-bindings: pinctrl: rt2880: add missing pin groups and functions
pinctrl: ingenic: Fix regmap on X series SoCs
pinctrl: nuvoton: Fix return value check in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: off by one in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: select GENERIC_PINCTRL_GROUPS
pinctrl: nuvoton: Fix sparse warning
pinctrl: mediatek: mt8186: Account for probe refactoring
pinctrl: mediatek: common-v1: Commonize spec_ies_smt_set callback
pinctrl: mediatek: common-v1: Commonize spec_pupd callback
pinctrl: mediatek: common-v1: Use common probe function
pinctrl: mediatek: common-v1: Add common probe function
pinctrl: mediatek: paris: Unify probe function by using OF match data
pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
pinctrl: berlin: fix error return code of berlin_pinctrl_build_state()
pinctrl: qcom: Introduce sc8280xp TLMM driver
...
Right now, when a gpio value is set, the actual hardware pin gets set
asynchronously. When linux write the output register, it takes some time
until it is actually propagated to the output shift registers. If that
output port is connected to an I2C mux for example, the linux driver
assumes the I2C bus is already switched although it is not.
Fortunately, there is a single shot mode with a feedback: you can
trigger the single shot and the hardware will clear that bit once it has
finished the clocking and strobed the load signal of the shift
registers. This can take a considerable amount of time though.
Measuremens have shown that it takes up to a whole burst cycle gap which
is about 50ms on the largest setting. Therefore, we have to mark the
output bank as sleepable. To avoid unnecessary waiting, just trigger the
single shot if the value was actually changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-6-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sgpio_output_set() return an error value. Don't just ignore the
return value of any regmap access but propagate it to our callers. Even
if the accesses never fail, this is a preparation patch to add single
shot mode where we need to poll a bit and thus we might get -ETIMEDOUT.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-5-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt ack register has the usual "write one to clear" semantics.
No read-modify-write is required here.
This is also a preparation patch to change the sgpio_clrsetbits() to use
regmap_update_bits() which don't write the value if it is not changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fix the following sparse warnings:
drivers/pinctrl/pinctrl-microchip-sgpio.c:63:31: warning: symbol 'properties_luton' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:68:31: warning: symbol 'properties_ocelot' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:73:31: warning: symbol 'properties_sparx5' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1606218173-3722-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
