Without that patch if you use specific resolutions like 1280x1024,
I can see distortion in the output. It seems as if the
frequency for updating the pixel of the image is out of sync.
For initialization tmds needs to be active, but can be disabled after init
to fix blurry display
Signed-off-by: chunhui dai <chunhui.dai@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
On K3 AM654x/J721E platforms the Port MII mode selection register(s) have
similar format and placed in the System Control Module (SCM) module
sequentially as one register per port, but, depending SOC and CPSW
instance, the base offset and number of ports can be different.
Hence, add possibility to retrieve number of ports and base registers
offset from DT and support for max possible number of ports supported by K3
SoCs like J721E.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20200828201943.29155-4-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
mtk_hdmi_phy is currently placed inside mediatek drm driver, but it's
more suitable to place a phy driver into phy driver folder, so move
mtk_hdmi_phy driver into phy driver folder.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
This addresses Silicon Errata:
i2075 - "USB2PHY: USB2PHY Charger Detect is Enabled by Default Without VBUS
Presence"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200824075127.14902-2-rogerq@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There were some problem in ipq8074 Gen2 PCIe phy init sequence.
1. Few register values were wrongly updated in the phy init sequence.
2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter
register which is added in serdes table causing the wrong register
was getting updated.
3. Clocks and resets were not added in the phy init.
Fix these to make Gen2 PCIe port on ipq8074 devices to work.
Fixes: eef243d04b ("phy: qcom-qmp: Add support for IPQ8074")
Cc: stable@vger.kernel.org
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1596036607-11877-4-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
regfield handling in current driver code is made complicated
by having a separate regfield variable for each field which
is allocated individually.
This quickly gets unwieldy once number of regfields increase.
Instead, use an array of regfields which are allocated in a
loop.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200727194603.44636-2-nsekhar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of a busy waiting while loop using udelay
use readl_poll_timeout function to check the condition
is met or timeout occurs in crport_handshake function.
readl_poll_timeout is called in non atomic context so
it safe to sleep until the condition is met.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20200720173502.542-1-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently when reading of the device property for "qcom,tx-deamp_3_5db"
fails the default is being assigned incorrectly to phy_dwc3->rx_eq. This
looks like a copy-n-paste error and in fact should be assigning the
default instead to phy_dwc3->tx_deamp_3_5db
Addresses-Coverity: ("Copy-paste error")
Fixes: ef19b117b8 ("phy: qualcomm: add qcom ipq806x dwc usb phy driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200721150613.416876-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mvneta hardware appears to lock up in various random ways when
repeatedly switching speeds between 1G and 2.5G, which involves
reprogramming the COMPHY. It is not entirely clear why this happens,
but best guess is that reprogramming the COMPHY glitches mvneta clocks
causing the hardware to fail. It seems that rebooting resolves the
failure, but not down/up cycling the interface alone.
Various other approaches have been tried, such as trying to cleanly
power down the COMPHY and then take it back through the power up
initialisation, but this does not seem to help.
It was finally noticed that u-boot's last step when configuring a
COMPHY for "SGMII" mode was to poke at a register described as
"GBE_CONFIGURATION_REG", which is undocumented in any external
documentation. All that we have is the fact that u-boot sets a bit
corresponding to the "SGMII" lane at the end of COMPHY initialisation.
Experimentation shows that if we clear this bit prior to changing the
speed, and then set it afterwards, mvneta does not suffer this problem
on the SolidRun Clearfog when switching speeds between 1G and 2.5G.
This problem was found while script-testing phylink.
This fix also requires the corresponding change to DT to be effective.
See "ARM: dts: armada-38x: fix NETA lockup when repeatedly switching
speeds".
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1jxtRj-0003Tz-CG@rmk-PC.armlinux.org.uk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If CONFIG_DEBUG_SHIRQ was enabled, r8a77951-salvator-xs could boot
correctly. If we appended "earlycon keep_bootcon" to the kernel
command like, we could get kernel log like below.
SError Interrupt on CPU0, code 0xbf000002 -- SError
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc3-salvator-x-00505-g6c843129e6faaf01 #785
Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT)
pstate: 60400085 (nZCv daIf +PAN -UAO BTYPE=--)
pc : rcar_gen3_phy_usb2_irq+0x14/0x54
lr : free_irq+0xf4/0x27c
This means free_irq() calls the interrupt handler while PM runtime
is not getting if DEBUG_SHIRQ is enabled and rcar_gen3_phy_usb2_probe()
failed. To fix the issue, move the irq registration place to
rcar_gen3_phy_usb2_init() which is ready to handle the interrupts.
Note that after the commit 549b6b55b0 ("phy: renesas: rcar-gen3-usb2:
enable/disable independent irqs") which is merged into v5.2, since this
driver creates multiple phy instances, needs to check whether one of
phy instances is initialized. However, if we backport this patch to v5.1
or less, we don't need to check it because such kernel have single
phy instance.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 9f391c574e ("phy: rcar-gen3-usb2: add runtime ID/VBUS pin detection")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594986297-12434-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver uses GPIO functions but doesn't include the header explcitly. Add
that to fix build errors when GPIOLIB is disabled.
drivers/phy/allwinner/phy-sun4i-usb.c:367:11: error: implicit
declaration of function ‘gpiod_get_value_cansleep’; did you mean
‘gpio_get_value_cansleep’? [-Werror=implicit-function-declaration]
drivers/phy/allwinner/phy-sun4i-usb.c:707:22: error: implicit
declaration of function ‘devm_gpiod_get_optional’; did you mean
‘devm_clk_get_optional’? [-Werror=implicit-function-declaration]
drivers/phy/allwinner/phy-sun4i-usb.c:708:11: error: ‘GPIOD_IN’
undeclared (first use in this function); did you mean ‘GPIOF_IN’?
drivers/phy/allwinner/phy-sun4i-usb.c:815:21: error: implicit
declaration of function ‘gpiod_to_irq’; did you mean ‘gpio_to_irq’?
[-Werror=implicit-function-declaration]
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20200716062427.71763-1-vkoul@kernel.org
devm_clk_get() and devm_reset_control_get() expect a const char *id for
the last arg, but a value of zero was provided. This results in below
sparse warning:
drivers/phy/st/phy-stm32-usbphyc.c:330:42: warning: Using plain integer as NULL pointer
drivers/phy/st/phy-stm32-usbphyc.c:343:52: warning: Using plain integer as NULL pointer
Instead of zero, use NULL
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200708132809.265967-6-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
