Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kmalloc(). For example:
struct wcn36xx_hal_ind_msg {
struct list_head list;
size_t msg_len;
u8 msg[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220208015606.1514022-1-chi.minghao@zte.com.cn
More than 20000 PPDU id jumping causing status ring and destination
ring processing not sync. The status ring is processed and the
destination ring is not processed. Since destination is not reaped for
so long, backpressure occurs at the destination ring.
To address this issue update the PPDU id with the latest PPDU, this
will allow the destination ring to be reaped and will prevent the
rings from getting out of sync.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220210064706.6171-1-quic_kathirve@quicinc.com
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-2-git-send-email-quic_vnaralas@quicinc.com
Fix WARN_ON() from ath11k_mac_update_vif_chan() if vdev is not up.
Since change_chanctx can be called even before vdev_up from
ieee80211_start_ap->ieee80211_vif_use_channel->
ieee80211_recalc_radar_chanctx.
Do vdev stop followed by a vdev start in case of vdev is down.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-1-git-send-email-quic_vnaralas@quicinc.com
mt76 patches for 5.18
- mt7915 mcu code cleanup
- mt7916 support
- fixes for SDIO support
- fixes for DFS
- power management fixes
- stability improvements
- background radar detection support
In AP mode, when a STA associate to us, we need to create an entry in
firmware and hardware, and then they can transmit data properly.
The entry index called mac_id which is assigned when sta_add, and we ask
firmware to create an entry for an associated station. Also, the address
CAM should be filled so hardware can know which packet is ours, and lookup
the mac_id for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-5-pkshih@realtek.com
vif_type mapping indicates hardware operating mode corresponding to vif
type. In STA mode, hardware mode should be INFRA or NO_LINK mode
dynamically according to association status. Since AP mode don't need to
change this by association status intuitively, just do the mapping in
STA mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-4-pkshih@realtek.com
In AP mode, each connected station needs an entry of address CAM. The
address CAM of vif is still needed to assit in AP itself.
For station mode, it still uses vif's address CAM.
Add a help macro rtw89_get_addr_cam_of() to get addr_cam from vif or sta
for all use cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-3-pkshih@realtek.com
Fill mac_id and self_role depends on the operation mode.
In AP mode, echo connected station has an unique mac_id, and each vif also
has one mac_id to represent itself.
The self_role is assigned to vif if the operation mode is decided, and
RTW89_SELF_ROLE_AP_CLIENT is assigned to the connected STA in AP mode,
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-2-pkshih@realtek.com
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not always copy ethernet header in mt{7615,7915,7921}_reverse_frag0_hdr_trans
and use a pointer instead.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of checking if any queue has not made progress since the last run,
only trigger hang detection if one of the queues has not made any progress
in 10 subsequent runs. This should reduce false positive firmware restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On AP mode devices, check beacon tx counters to detect MAC errors.
When an error is detected, stop the MAC before resetting it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Apply sleep mode by default to reduce power consumption as possible.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
without this change, the fixed MCS only supports 1 Nss.
Fixes: 70fd1333cd ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Should use peer's bandwidth instead of chandef->width to
get correct mcs_map.
Fixes: 76be6c076c ("mt76: mt7915: add .set_bitrate_mask() callback")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Always release fw data at the end of mt7921_load_patch routine.
Fixes: 78b217580c ("mt76: mt7921s: fix bus hang with wrong privilege")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free allocated skb in mt7915_mcu_add_sta routine in case of failures.
Fixes: 89bbd3730f ("mt76: mt7915: rework starec TLV tags")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The radar detctor is used for dfs channel. So it will start after switching
to dfs channel and will stop after leaving. The TX will be blocked if radar
detctor isn't stopped in non-dfs channel.
This patch resets the dfs state to indicate the radar detector needs to be
stopped.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check sta_rates pointer value in mt7615_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing mt76_connac_pm_dequeue_skbs routine waking up mt7663s device
from runtime-pm sleep state.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove duplicated DATA4_SU_MU_SPTL_REUSE flag configuration in
mt7921_mac_decode_he_radiotap routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing DATA4_TB_SPTL_REUSE1 he radiotap flag to
mt7915_mac_decode_he_radiotap routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_connac_lmac_mapping is shared between mt7921 and mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
