The .value is a two-dim array, not a pointer.
struct iqk_matrix_regs {
bool iqk_done;
long value[1][IQK_MATRIX_REG_NUM];
};
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The design of INT indicator register (R_AX_PCIE_HIMR00_V1) is to reduce IO
during frequent interrupts, because it can stop chip sending interrupt to
host if we just set this indicator to 0, not all IMR(s). This indicator
register looks like a root interrupt controller of wifi chip.
However, we can't set all other IMR(s) to 0 during we are running on
interrupt service routine, or the indicator register can't reflect the
status of certain interrupt happened during this period, and then miss
some interrupts especially SER interrupt events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-7-pkshih@realtek.com
This initial vesion is usable now. It can support STA, AP and monitor
modes, so we can add 8852ce to Kconfig and Makefile.
We are still working on some features, such as deep power save, and BT
coexistence. But, this version still can have a good WiFi-only performance
already, and will continue to fine tune power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-9-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-5-pkshih@realtek.com
After scan aborts we still receive some hw scan c2h packets, and
processing these c2h commands will change current channel. If device
already connect to other AP, driver will set wrong op channel due
to current channel changed. The disconnection happens when hw scan back
to wrong op channel that device can't receive beacon from AP. To fix
this issue, we ignore the late c2h if we are not scanning, and set
current channel back to op channel after scan to align the FW behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-3-pkshih@realtek.com
Using not existing queues can panic the kernel with rtl8180/rtl8185 cards.
Ignore the skb priority for those cards, they only have one tx queue. Pierre
Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum:
https://forums.gentoo.org/viewtopic-t-1147832-postdays-0-postorder-asc-start-25.html
He also confirmed that this patch fixes the issue. In summary this happened:
After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a
"divide error: 0000" when connecting to an AP. Control port tx now tries to
use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in
2.10.
Since only the rtl8187se part of the driver supports QoS, the priority
of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185
cards.
rtl8180 is then unconditionally reading out the priority and finally crashes on
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this
patch:
idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries
"ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got
initialized.
Cc: stable@vger.kernel.org
Reported-by: pa@panix.com
Tested-by: pa@panix.com
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de
Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and
::init_txpwr_unit are called when we up interface and then configure TX
power registers to initial values. The ::set_txpwr_ctrl is to configure
'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the
same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power
compensation depends on thermal value) control and bandedge.
The ::set_txpwr is called once switching channel. First, it sets TX power
for each rate section (e.g. CCK, OFDM), and then sets TX power offset
between 1SS and 2SS rate. Finally, it sets TX power limit to prevent
power over regulation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-12-pkshih@realtek.com
When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:
rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com
In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com
