Similar to mt7915 driver, do not aggregate injected frames in
HW A-MSDU block.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, mt7915e does not enable thermal management until the default
thermal zone does not reach a trip point. If the rest of the system
have better cooling than the wireless hardware, then it is possible that
the wireless chip can overheat while the rest of the system is fine.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware-controlled actual throttle state was previously available
by reading the cooling_device, but this confused the thermal subsystem.
Add a hwmon attribute to get it instead.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915e registers a cooling_device with wrong semantics:
1. cooling_device expect that higher states values should cool more, but
mt7915e did the opposite... with the exception of state == 0, which
should "disable thermal management", but does not seem to have any
effect since the previous state is kept.
The result is that when the thermal zone heats up a bit and bumps the
cooling_device state from 0 to 1 to cool a bit, the performance is
destroyed, and when going back from 1 to 0, the performance stays bad.
2. Reading the cooling_device state does not always return the last
written state, but can return the actual hardware throttle state,
which is different.
This is a problem because the mt7915 firmware actually implement the
equivalent of a thermal zone with trip points. Setting the cooling
device state actually changes the throttles at each trip point, so the
following could occur if the first issue is fixed:
- thermal subsystem set state to 100% power (state=0)
- mt7915e driver set trip throttles to [100%, 50%, 25%, 12%]
- hardware heats up and decides to switch to 50% power
- thermal subsystem see that power is 50% (state=50), decide to increase
it to 60% (state=40) because the rest of the system is cool.
- mt7915e driver set trip throttle to [60%, 30%, 15%, 7%]
- hardware thus switches to 30% power
[race to the bottom continues...]
This patch corrects the semantics of the cooling_device to the one that
the thermal subsystem expect it.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The muru enable/disable are only set after the first station connection.
Without this patch, the firmware couldn't enable muru
if the first connected station is non-HE type.
Fixes: 16bff457dd ("mt76: mt7915: rework mt7915_mcu_sta_muru_tlv()")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer chips such as MT7915 require up to 16-bits for this field.
Fixes: 49126ac1f8 ("mt76: connac: move mt76_connac_mcu_bss_basic_tlv in connac module")
Signed-off-by: Chad Monroe <chad.monroe@smartrg.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in mt7915_mac_tx_free routine:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] *cur_info
got restricted __le32 *
warning: cast to restricted __le32
Fixes: c17780e7b2 ("mt76: mt7915: add txfree event v3")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warnings:
warning: incorrect type in initializer (different base types)
expected restricted __le16 [usertype] msg_type
got int
warning: incorrect type in assignment (different base types)
expected restricted __le32 [usertype] timestamp
got unsigned int
Fixes: 988845c936 ("mt76: mt7915: add support for passing chip/firmware debug data to user space")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The following error is see from the compiler:
mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’:
mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
The issue is due to allocating a buffer as string storage.
Fix by converting to a dynamical allocation of the buffer.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before, the hardware would be allowed to transmit injected 802.11 MPDUs
as A-MSDU. This resulted in corrupted frames being transmitted. Now,
injected MPDUs are transmitted as-is, without A-MSDU.
The fix was verified with frame injection on MT7915 hardware, both with
and without the injected frame being encrypted.
If the hardware cannot do A-MSDU aggregation on MPDUs, this problem
would also be present in the TX path where mac80211 does the 802.11
encapsulation. However, I have not observed any such problem when
disabling IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD to force that mode.
Therefore this fix is isolated to injected frames only.
The same A-MSDU logic is also present in the mt7921 driver, so it is
likely that this fix should be applied there too. I do not have access
to mt7921 hardware so I have not been able to test that.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not always copy ethernet header in mt{7615,7915,7921}_reverse_frag0_hdr_trans
and use a pointer instead.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of checking if any queue has not made progress since the last run,
only trigger hang detection if one of the queues has not made any progress
in 10 subsequent runs. This should reduce false positive firmware restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On AP mode devices, check beacon tx counters to detect MAC errors.
When an error is detected, stop the MAC before resetting it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Apply sleep mode by default to reduce power consumption as possible.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
without this change, the fixed MCS only supports 1 Nss.
Fixes: 70fd1333cd ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Should use peer's bandwidth instead of chandef->width to
get correct mcs_map.
Fixes: 76be6c076c ("mt76: mt7915: add .set_bitrate_mask() callback")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Always release fw data at the end of mt7921_load_patch routine.
Fixes: 78b217580c ("mt76: mt7921s: fix bus hang with wrong privilege")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free allocated skb in mt7915_mcu_add_sta routine in case of failures.
Fixes: 89bbd3730f ("mt76: mt7915: rework starec TLV tags")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The radar detctor is used for dfs channel. So it will start after switching
to dfs channel and will stop after leaving. The TX will be blocked if radar
detctor isn't stopped in non-dfs channel.
This patch resets the dfs state to indicate the radar detector needs to be
stopped.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check sta_rates pointer value in mt7615_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing mt76_connac_pm_dequeue_skbs routine waking up mt7663s device
from runtime-pm sleep state.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove duplicated DATA4_SU_MU_SPTL_REUSE flag configuration in
mt7921_mac_decode_he_radiotap routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing DATA4_TB_SPTL_REUSE1 he radiotap flag to
mt7915_mac_decode_he_radiotap routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_connac_lmac_mapping is shared between mt7921 and mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rdd_monitor debugfs node in order to dump rdd2 configuration.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
