When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.6f69fe6e4128.I921d4ae20ef5276716baeeeda0b001cf25b9b968@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For simplicity we assume that msix has 2 IRQ lines one used for rx data
called msix_non_share, and another used for one bit flags messages
(alive, hw error, sw error, rx data flag) called msix_share.
Every time the FW has data to send it puts it on the RX queue and HW
turns on the flags in msix_share (inta_fw) indicating about rx data,
and HW sends an interrupt a bit later to the msix_non_share _unless_
the msix_shared RX data bit was cleared.
Currently in the code every time we get an msix_shared we clear all bits
including rx data queue bits.
So we can have a race
----------------------------------------------------
DRIVER | HW | FW
----------------------------------------------------
- send host cmd to FW | |
| | - handle message
| | and put a response
| | on the RX queue
| - RX flag on |
| | - send alive msix
| - alive flag on |
| - interrupt |
| msix_share driver |
- handle msix_shared | |
and clear all flags | |
bits | |
| - don't send an |
| interrupt on |
| msix_non_shared |
| (driver cleared) |
- driver timeout on | |
waiting for host cmd | |
respond | |
| |
----------------------------------------------------
The change is to clear only the msi_shared flags that are handled in
the msix_shared flow, which will cause the hardware to send an interrupt
on the msix_non_share line as well, when it has data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.a1cdda2fa270.I02a82312679f4541f30bb8db8747a797dbb70ee7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently have a special, separate, code path to acquire NIC
access for the in-flight host-command workaround on 7000 series
hardware. However, the normal code path here has grown a number
of additional workarounds/semantics over time, such as reprobing
the device if things fail.
Rather than try to replicate any of this logic, call the normal
grab_nic_access logic for the workaround.
This changes the spinlock to _bh, but that's OK since it's just
redundant, we already have soft-IRQs disabled when we get here,
and so didn't (have to) do it again. Since it's only for commands
there's however no point in making the code more complex just to
not use _bh here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.d196fc6ffb23.Idc1ce3ce9fed9178beee7e5409bc669f79b06a0d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unfortunately, since beacon protection isn't fully available
yet, we didn't notice that there are problems with it and
that the replay detection isn't working correctly. We were
relying only on mac80211, since iwl_mvm_rx_crypto() exits
when !ieee80211_has_protected(), which is of course true for
protected (but not encrypted) management frames.
Fix this to properly detect protected (but not encrypted)
management frames and handle them - we continue to only care
about beacons since for others everything can and will be
checked in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.23c990843369.I09c262a8f6f9852cc8f513cdcb31a7f8f87dd8af@changeid
As the context info gen3 code is only called for >=AX210 devices
(from iwl_trans_pcie_gen2_start_fw()) the code there to set LTR
on 22000 devices cannot actually do anything (22000 < AX210).
Fix this by moving the LTR code to iwl_trans_pcie_gen2_start_fw()
where it can handle both devices. This then requires that we kick
the firmware only after that rather than doing it from the context
info code.
Note that this again had a dead branch in gen3 code, which I've
removed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: ed0022da8b ("iwlwifi: pcie: set LTR on more devices")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.675486178ed1.Ib61463aba6920645059e366dcdca4c4c77f0ff58@changeid
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
Second set of fixes for v5.12. Only three iwlwifi fixes this time, the
crash with MVM being the most important one and reported by multiple
people.
iwlwifi
* fix kernel crash regression when using LTO with MVM devices
* fix printk format warnings
* fix potential deadlock found by lockdep
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
First set of fixes for v5.12. One iwlwifi kernel crash fix and smaller
fixes to multiple drivers.
ath9k
* fix Spatial Multiplexing Power Save (SMPS) handling to improve thoughtput
mt76
* error handling fixes
* memory leax fixes
iwlwifi
* don't crash during debug collection on DVM devices
MAINTAINERS
* email address update
ath11k
* fix GCC warning about DMA address debug messages
* fix regression which broke QCA6390 AP mode
* tag 'wireless-drivers-2021-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: mt7915: fix unused 'mode' variable
mt76: dma: do not report truncated frames to mac80211
mt76: mt7921: remove incorrect error handling
iwlwifi: pcie: fix iwl_so_trans_cfg link error when CONFIG_IWLMVM is disabled
ath11k: fix AP mode for QCA6390
ath11k: qmi: use %pad to format dma_addr_t
MAINTAINERS: update for mwifiex driver maintainers
iwlwifi: avoid crash on unsupported debug collection
mt76: mt7915: only modify tx buffer list after allocating tx token id
mt76: fix tx skb error handling in mt76_dma_tx_queue_skb
ath9k: fix transmitting to stations in dynamic SMPS mode
====================
Link: https://lore.kernel.org/r/20210226164411.CDD03C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
Currently, for all devices and families, failing getting the temp
from the fw is indicated in the log as ERR.
This is too severe for two reasons:
1. The driver has a fall back - and schedules the next temp
read immediately after failing to read temp from the fw.
2. The temp read implementation in the fw is different between
HWs, and on older devices the flow is a-sync and may timeout.
Reducing the print severity from ERR to WARN will allow to
track the issue if it will appear many times, but not frighten users
if it appears once.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.dfd423b2b2ef.Icd576dc3e2e7174d3ed9c1c32f48ea0013699e72@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
