Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.
Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.
Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).
The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.
Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.
Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com
Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
Don't return early when the flash is smaller than or equal to 16MiB. We
need to be able to register hooks for all sizes of flashes. This also has
the benefit that it increases the readability of the code because the
action, i.e. registering the fixups, is connected to the condition, i.e.
flashes larger than 16MiB.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-28-michael@walle.cc
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
