Reduce the number of exported symbols by replacing:
- mtd_expert_analysis_warning (the error string)
- mtd_expert_analysis_mode (the boolean)
with a single helper:
- mtd_check_expert_analysis_mode
Calling this helper will both check/return the content of the internal
boolean -which is not exported anymore- and as well conditionally
WARN_ONCE() the user, like it was done before.
While on this function, make the error string local to the helper and
set it const. Only export this helper when CONFIG_DEBUG_FS is defined to
limit the growth of the Linux kernel size only for a debug feature on
production kernels.
Mechanically update all the consumers.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220128113414.1121924-1-miquel.raynal@bootlin.com
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent
otherwise. There are several drivers using this macro which keep their
of_device_id array enclosed within an #ifdef CONFIG_OF check, these are
considered fine. However, When misused, the of_device_id array pointed
by this macro will produce a warning because it is finally unused when
compiled without OF support.
A number of fixes are possible:
- Always depend on CONFIG_OF, but this will not always work and may
break boards.
- Enclose the compatible array by #ifdef's, this may save a bit of
memory but will reduce build coverage.
- Tell the compiler the array may be unused, if this can be avoided,
let's not do this.
- Just drop the macro, setting the of_device_id array for a non OF
enabled platform is not an issue, it will just be unused.
The latter solution seems the more appropriate, so let's use it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
In the i.MX28 manual (MCIMX28RM, Rev. 1, 2010) you can find an example
(15.2.4 High-Speed NAND Timing) of how to configure the GPMI controller
to manage High-Speed NAND devices, so it was wrong to assume that only
i.MX6 can achieve EDO timings.
This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4).
Kernel mtd tests:
- mtd_nandbiterrs
- mtd_nandecctest
- mtd_oobtest
- mtd_pagetest
- mtd_readtest
- mtd_speedtest
- mtd_stresstest
- mtd_subpagetest
- mtd_torturetest [cycles_count = 10000000]
run without errors.
Before this patch (mode 0):
---------------------------
eraseblock write speed is 2098 KiB/s
eraseblock read speed is 2680 KiB/s
page write speed is 1689 KiB/s
page read speed is 2522 KiB/s
2 page write speed is 1899 KiB/s
2 page read speed is 2579 KiB/s
erase speed is 128000 KiB/s
2x multi-block erase speed is 73142 KiB/s
4x multi-block erase speed is 204800 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
After this patch (mode 5):
-------------------------
eraseblock write speed is 3390 KiB/s
eraseblock read speed is 5688 KiB/s
page write speed is 2680 KiB/s
page read speed is 4876 KiB/s
2 page write speed is 2909 KiB/s
2 page read speed is 5224 KiB/s
erase speed is 170666 KiB/s
2x multi-block erase speed is 204800 KiB/s
4x multi-block erase speed is 256000 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-5-dario.binacchi@amarulasolutions.com
What to do when the real rate of the gpmi clock is not equal to the
required one? The solutions proposed in [1] did not lead to a conclusion
on how to validate the clock rate, so, inspired by the document [2], I
consider the rate correct only if not lower or equal to the rate of the
previous edo mode. In fact, in chapter 4.16.2 (NV-DDR) of the document [2],
it is written that "If the host selects timing mode n, then its clock
period shall be faster than the clock period of timing mode n-1 and
slower than or equal to the clock period of timing mode n.". I thought
that it could therefore also be used in this case, without therefore
having to define the valid rate ranges empirically.
For example, suppose that gpmi_nfc_compute_timings() is called to set
edo mode 5 (100MHz) but the rate returned by clk_round_rate() is 80MHz
(edo mode 4). In this case gpmi_nfc_compute_timings() will return error,
and will be called again to set edo mode 4, which this time will be
successful.
[1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
[2] http://www.onfi.org/-/media/client/onfi/specs/onfi_3_0_gold.pdf?la=en
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-4-dario.binacchi@amarulasolutions.com
Add a BCMA shim to allow us to register the brcmnand driver using the
BCMA bus which provides indirect memory mapped access to SoC registers.
There are a number of registers that need to be byte swapped because
they are natively big endian, coming directly from the NAND chip, and
there is no bus interface unlike the iProc or STB platforms that
performs the byte swapping for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-10-f.fainelli@gmail.com
In order to initialize a given chip select object for use by the
brcmnand driver, move all of the Device Tree specific routines outside
of brcmnand_init_cs() in order to make it usable in a platform data
configuration which will be necessary for supporting BCMA chips.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-5-f.fainelli@gmail.com
Allow a brcmnand_soc instance to provide a custom set of I/O operations
which we will require when using this driver on a BCMA bus which is not
directly memory mapped I/O. Update the nand_{read,write}_reg accordingly
to use the SoC operations if provided.
To minimize the penalty on other SoCs which do support standard MMIO
accesses, we use a static key which is disabled by default and gets
enabled if a soc implementation does provide I/O operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-3-f.fainelli@gmail.com
of_get_nand_bus_width() had a wrong behavior because:
1/ it ignored the -ENODATA and -EOVERFLOW return values of
of_property_read_u32(). "nand-bus-width" without value was tolerated
while it shouldn't have been according to the devicetree bindings.
2/ returned -EIO when the nand-bus-width was neither 8 nor 16, when it
should have returned -EINVAL instead.
3/ returned the 8 or 16 bus-width integer, but it was never used it its
caller. A simply return 0 on success is enough.
Rework of_get_nand_bus_width() and address all the above. The execution
is now stopped in case of errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220106131610.225661-2-tudor.ambarus@microchip.com
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 2c22120fbd ("MTD: OneNAND: interrupt based wait support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220104162658.1988142-1-jiasheng@iscas.ac.cn
Add the necessary helpers to register/unregister hardware ECC engines
that will be called from ECC engine drivers.
Also add helpers to get the right engine from the user
perspective. Keep a reference of the in use ECC engine in order to
prevent modules to be unloaded. Put the reference when the engine gets
retired.
A static list of hardware (only) ECC engines is setup to keep track of
the registered engines.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-13-miquel.raynal@bootlin.com
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
After removal of RBTX4939 board support remove code for the TX4939 SoC.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Raw NAND core:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Memory controller drivers for v5.17 - OMAP GPMC
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
[miquel.raynal@bootlin.com: A first commit introduced a new omap
compatible and another moved the IDs to a header which created a
conflict: moving the new ID as well in the header fixed it.]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAND on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now NAND must be resumed using
runtime PM API in order to initialize the NAND power state. Add runtime PM
and OPP support to the NAND driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
