Currently phram always uses ioremap(), but this is unnecessary when
normal memory is used. If the reserved-memory node does not specify the
no-map property, indicating it should be mapped as system RAM and
ioremap() cannot be used on it, use a cached mapping using
memremap(MEMREMAP_WB) instead.
On one of my systems this improves read performance by ~70%.
(Note that this driver has always used normal memcpy/memset functions on
memory obtained from ioremap(), which sparse doesn't like. There is no
memremap() variant which maps exactly to ioremap() on all architectures,
so that behaviour of the driver is not changed to avoid affecting
existing users, but the sparse warnings are suppressed in the moved code
with __force.)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220510151822.1809278-1-vincent.whitchurch@axis.com
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-4-broonie@kernel.org
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-3-broonie@kernel.org
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent
otherwise. There are several drivers using this macro which keep their
of_device_id array enclosed within an #ifdef CONFIG_OF check, these are
considered fine. However, When misused, the of_device_id array pointed
by this macro will produce a warning because it is finally unused when
compiled without OF support.
A number of fixes are possible:
- Always depend on CONFIG_OF, but this will not always work and may
break boards.
- Enclose the compatible array by #ifdef's, this may save a bit of
memory but will reduce build coverage.
- Tell the compiler the array may be unused, if this can be avoided,
let's not do this.
- Just drop the macro, setting the of_device_id array for a non OF
enabled platform is not an issue, it will just be unused.
The latter solution seems the more appropriate, so let's use it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
The problem is that "erasesize" is a uint64_t type so it might be
non-zero but the lower 32 bits are zero so when it's truncated,
"(uint32_t)erasesize", then that value is zero. This leads to a
divide by zero bug.
Avoid the bug by delaying the divide until after we have validated
that "erasesize" is non-zero and within the uint32_t range.
Fixes: dc2b3e5cbc ("mtd: phram: use div_u64_rem to stop overwrite len in phram_setup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220121115505.GI1978@kadam
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_ids are
missing for the dataflash driver and the following warnings are now
seen.
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
Fix this by adding the necessary spi_device_ids.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130112443.107730-1-jonathanh@nvidia.com
This patch adds support for an optional MTD label for mtd2block emulated
MTD devices. Useful when, e.g., testing device images using Qemu.
The following line in /etc/fstab can then be used to mount a file system
regardless if running on an embedded system, or emulated with block2mtd:
mtd:Config /mnt jffs2 noatime,nodiratime 0 0
Kernel command line syntax in the emulated case:
block2mtd.block2mtd=/dev/sda,,Config
Notice the ',,' it is the optional erase_size, which like before this
patch, defaults to PAGE_SIZE when omitted. Hence the strlen() check.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211009060955.552636-3-troglobit@gmail.com
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
We now support user to set erase page size, and use do_div between len
and erase size to determine the reasonableness for the erase size.
However, do_div is a macro and will overwrite the value of len. Which
results a mtd device with unexcepted size. Fix it by use div_u64_rem.
Fixes: ffad560394 ("mtd: phram: Allow the user to set the erase page size.")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210125124936.651812-1-yangerkun@huawei.com
It seems that several hardware ECC engine use a swapped representation
of bytes compared to software. This might having to do with how the
ECC engine is wired to the NAND controller or the order the bits are
passed to the hardware BCH logic.
This means that when the software BCH engine is working in conjunction
with data generated with hardware, sometimes we might need to swap the
bits inside bytes, eg:
0x0A = b0000_1010 -> b0101_0000 = 0x50
Make it possible by adding a boolean to the BCH initialization routine.
Regarding the implementation itself, this is a rather simple approach
that can probably be enhanced in the future by preparing the
->a_{mod,pow}_tab tables with the swapping in mind.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-3-miquel.raynal@bootlin.com
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1
00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15
00000010
Fixes: 4379075a87 ("mtd: mchp23k256: Add support for mchp23lcv1024")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bf ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/devices/spear_smi.c: In function spear_smi_probe_config_dt:
drivers/mtd/devices/spear_smi.c:780:32: warning: variable flash_info set but not used [-Wunused-but-set-variable]
It is not used since commit 6551ab5d30 ("mtd:
add device-tree support to spear_smi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/devices/pmc551.c: In function pmc551_erase:
drivers/mtd/devices/pmc551.c:142:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_read:
drivers/mtd/devices/pmc551.c:232:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_write:
drivers/mtd/devices/pmc551.c:289:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
It is not used since commit cdf0a7d169 ("[MTD]
pmc551 whitespace cleanup")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The phram code implements managing multiple devices through a linked
list.
However, due to the module parameter permission of 0, the
/sys/module/phram/parameters/phram interface is missing.
The command line arguments in insmod can only create one device.
Therefore, add writable permissions to the module parameters, create
/sys/module/phram/parameters/phram interface, and create multi-device
support.
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The m25p80 driver is actually a generic wrapper around the spi-mem
layer. Not only the driver name is misleading, but we'd expect such a
common logic to be directly available in the core. Another reason for
moving this code is that SPI NOR controller drivers should
progressively be replaced by SPI controller drivers implementing the
spi_mem_ops interface, and when the conversion is done, we should have
a single spi-nor driver directly interfacing with the spi-mem layer.
While moving the code we also fix a longstanding issue when
non-DMA-able buffers are passed by the MTD layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
