During test campaign, and especially after several unbind/bind sequences,
it has been seen that the SD-card on SDMMC1 thread could freeze.
The freeze always appear on a CMD23 following a CMD19.
Checking SDMMC internal registers shows that the tuning command (CMD19)
has failed.
The freeze is then due to the delay block involved in the tuning sequence.
To correct this, clear the delay block register DLYB_CR register after
the tuning commands.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 1103f807a3 ("mmc: mmci_sdmmc: Add execute tuning with delay block")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211215141727.4901-4-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_SIMPLE_DEV_PM_OPS() instead of the SIMPLE_DEV_PM_OPS()
macro, along with using pm_sleep_ptr() as this driver doesn't handle
runtime PM.
This makes it possible to remove the #ifdef CONFIG_PM guard around
the suspend/resume functions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Use DEFINE_SIMPLE_DEV_PM_OPS() instead of the SIMPLE_DEV_PM_OPS()
macro. This makes it possible to remove the __maybe_unused flags
on the callback functions.
- Since we only have callbacks for suspend/resume, we can conditionally
compile the dev_pm_ops structure for when CONFIG_PM_SLEEP is enabled;
so use the pm_sleep_ptr() macro instead of pm_ptr().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SDHCI on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now SDHCI must be resumed using
runtime PM API in order to initialize the SDHCI power state. The SDHCI
clock rate must be changed using OPP API that will reconfigure the power
domain performance state in accordance to the rate. Add runtime PM and OPP
support to the SDHCI driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the common MMC_CAP_CMD23 capability to common_caps so that only the
special case of MMC_CAP_1_8V_DDR and MMC_CAP_8_BIT_DATA are set via
caps/num_caps. Both of those can, and should, be set via device tree
properties instead, so we can now say that exynos_dwmmc_caps is only
used for backwards compatibility.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-5-john@metanate.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMOUT register is always set with a full value for every transfer,
which (with a 200MHz clock) will give a full DRTO of ~84 milliseconds.
This is normally good enough to complete the request, but setting a full
value makes it impossible to test shorter timeouts, when for example
testing data read times on different SD cards.
Add a function to set any value smaller than the maximum of 0xFFFFFF.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211119155337.14341-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_send_op_cond(), loops are continuously performed at the same
interval of 10 ms. However the behaviour is not good for some eMMC
which can be out from a busy state earlier than 10 ms if normal.
Rather than fixing about the interval time in mmc_send_op_cond(),
let's instead convert into using the common __mmc_poll_for_busy().
The reason for adjusting the interval time is that it is important
to reduce the eMMC initialization time, especially in devices that
use eMMC as rootfs.
Test log(eMMC:KLM8G1GETF-B041):
before: 12 ms (0.311016 - 0.298729)
[ 0.295823] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 0.298729] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[ 0.311016] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[ 0.311336] mmc0: starting CMD2 arg 00000000 flags 00000007
after: 2 ms (0.301270 - 0.298762)
[ 0.295862] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 0.298762] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[ 0.299067] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.299441] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.299879] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.300446] mmc0: starting CMD1 arg 40000080 flags 000000e1
[ 0.301270] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[ 0.301572] mmc0: starting CMD2 arg 00000000 flags 00000007
Signed-off-by: Huijin Park <huijin.park@samsung.com>
Link: https://lore.kernel.org/r/20211104063231.2115-3-huijin.park@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get a data error during a block transfer command, a stop command
(CMD12) is normally initiated. But this does not work for the general
command (CMD56), but instead the action is ignored and an uninitialized
command struct is used for the stop action, with unexpected result.
Fix this by adding a check for GEN_CMD when preparing stop transmission.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211103182716.28419-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TiWi WL1251 WiFi chip needs special setup of the sdio
interface before it can be probed.
So far, this is done in omap_hsmmc_init_card() in omap_hsmmc.c
which makes it useable only if connected to omap devices
which use the omap_hsmmc. The OpenPandora is the most promient
example.
There are plans to switch to a newer sdhci-omap driver and
retire omap_hsmmc. Hence this quirk must be reworked or moved
somewhere else. Ideally to some location that is not dependent
on the specific SoC mmc host driver.
This is achieved by the new mmc_fixup_device() option introduced
by ("mmc: allow to match the device tree to apply quirks") to match
through device tree compatible string.
This quirk will be called early right after where host->ops->init_card()
and thus omap_hsmmc_init_card() was previously called.
Note that we do not need to transplant
card->ocr = 0x80;
because we rely on ("mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO").
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/774565df7f02124c003aaf8b879706352548f832.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This (initially empty) table allows to match quirks early based
on .compatible of the child node of some mmc/sdio interface.
This allows to add quirks based on device tree instead of having
card specific code in the host ops.
A new macro SDIO_FIXUP_COMPATIBLE makes the definition readable.
And we call mmc_fixup_device(sdio_card_init_methods) just after
where host->ops->init_card() can be optionally called.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b13fd8b3eebc3c23b6816b254a518c224cbdcfd4.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the special sdhci_acpi_no_fixup_child_power() helper which was
added to avoid triggering an ACPI tables bug on the GPD win/pocket
devices.
The ACPI child-device triggering this bug has now been added to the
acpi_device_override_status() quirk table, so that its status
field is set to all 0 (instead of the wrong return value from the _STA
ACPI method). This removes the need for the special handling in
the sdhci-acpi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All modern drivers can support extra partitions using the extended
dev_t. In fact except for the ioctl method drivers never even see
partitions in normal operation.
So remove the GENHD_FL_EXT_DEVT and allow extra partitions for all
block devices that do support partitions, and require those that
do not support partitions to explicit disallow them using
GENHD_FL_NO_PART.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211122130625.1136848-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This manually reverts 07b652cdbec3 ("mmc: card: Don't show eMMC RPMB and
BOOT areas in /proc/partitions"). Based on the commit description that
change was purely cosmetic. mmc is the last driver that sets this
flag and thus prevents it from being removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20211122130625.1136848-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_id is
missing for the MMC SPI driver and the following warning is now seen.
WARNING KERN SPI driver mmc_spi has no spi_device_id for mmc-spi-slot
Fix this by adding the necessary spi_device_id.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211115113813.238044-1-jonathanh@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Like the individual CCU drivers, it can be beneficial for memory
consumption of cross-platform configurations to only load the CCU core
on the relevant platform. For example, a generic arm64 kernel sees the
following improvement when building the CCU core and drivers as modules:
before:
text data bss dec hex filename
13882360 5251670 360800 19494830 12977ae vmlinux
after:
text data bss dec hex filename
13734787 5086442 360800 19182029 124b1cd vmlinux
So the result is a 390KB total reduction in kernel image size.
The one early clock provider (sun5i) requires the core to be built in.
Now that loading the MMC driver will trigger loading the CCU core, the
MMC timing mode functions do not need a compile-time fallback.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-5-samuel@sholland.org
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
This patch removes the old SD handling code and switch to the new one.
This updates the SDHI driver at the same time. Because the SDHI driver
can only communicate with the clock driver via clk_set_rate(), I don't
see an alternative to this flag-day-approach, so we cross subsystems
here.
The patch sadly looks messy for the CPG lib, but it is basically a huge
chunk of code removed and smaller chunks added. It looks much better
when you just view the resulting source file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20211110191610.5664-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
