Some of the machines, like Dell Precision 3630,
may expose LPSS devices via ACPI.
Add their IDs to the list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on the Intel Datasheet for the DH89xxCC PCH, the GPIO driver
is the same as ICH_v5_GPIO, minus the fact the DH89xxCC also has
blink support. However, blink support isn't supported by the GPIO
driver so we should use ICH_v5_GPIO. Tested and working on a Meraki
MX100-HW.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Co-developed-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for ClockMatrix(TM) and 82P33xxx families of timing
and synchronization devices. The access interface can be either
SPI or I2C. Currently, it will create 2 types of MFD devices,
which are to be used by the corresponding rsmu character device
driver and the PTP hardware clock driver, respectively.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Pull mfd updates from Lee Jones:
"Core Frameworks:
- Fix Software Node clean-up code
New Drivers:
- Add support for MediaTek MT6359 PMIC
- Add support for Qualcomm PM8008 PMIC
- Add support for Richtek RT4831
New Device Support:
- Add support for Audio CODECs to Rockchip RK817
- Add support for Alder Lake-M to Intel LPSS PCI
- Add support for Periph Device Charge to ChromeOS EC
New Functionality:
- Provide additional IRQs for wcd934x
- Add optional Reset functionality to lp87565
Fix-ups:
- Namespacing & visibility fixes to lp87565
- Differentiate between Power and Home key IRQs in mt6358
- Export I2C device tables in da9052-i2c, stmpe-i2c
- Adapt IRQ flags in max8907, rn5t61, max8907
- Make some functions/devices optional in axp20x, cros_ec_dev
- Explicitly include used header files in ioc3
- Remove superfluous lines in MAINTAINERS, sec-core, st,stm32-timers
- Resolve Kerneldoc issues in omap-usb-host, omap-usb-tll, si476x-cmd, si476x-i2c
- Convert arizona-core to a module
- Copyright changes in hi655x-pmic
- Drop support for board file initialisation in sec-core
- Trivial spelling, whitespace etc updates in lp87565, si476x-cmd,
mt6360-core, wm831x-core, twl-core, db8500-prcmu
- Simplify various implementations of wcd934x, mt6360-core, max8997,
max8998, da9052-i2c, da9062-core, sec-core,
- Device Tree binding changes in google,cros-ec,
richtek,rt4831-backlight, db8500-prcmu, qcom,pm8008, qcom,spmi-pmic
- Use provided APIs to simplify t7l66xb, as3722, da9055-core,
tps80031, 88pm800, 88pm805, asic3, sun6i-prcm, wm831x-core,
wm831x-otp, ucb1x00-assabet, timberdale, sm501, pcf50633-core,
kempld-core, janz-cmodio, intel_soc_pmic_bxtwc, ab8500-core
Bug Fixes:
- Fix unused variable warning in rk817_codec
- Fix regulator voltage configuration in rohm-bd71828
- Fix ongoing freeing of regmap_config 'name' issue in syscon
- Fix error handling path in da9063-i2c
- Fix Kconfig issues in MFD_MP2629
- Fix DMA mask warnings in motorola-cpcap"
* tag 'mfd-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (83 commits)
mfd: cros_ec: Add peripheral device charger
mfd: max8907: Remove IRQF_NO_AUTOEN flag
mfd: ab8500-core: Use DEVICE_ATTR_RO/RW macro
mfd: intel_soc_pmic_bxtwc: Use DEVICE_ATTR_ADMIN_RW macro
mfd: janz-cmodio: Use DEVICE_ATTR_RO macro
mfd: kempld-core: Use DEVICE_ATTR_RO macro
mfd: pcf50633: Use DEVICE_ATTR_ADMIN_RO macro
mfd: sm501: Use DEVICE_ATTR_RO macro
mfd: timberdale: Use DEVICE_ATTR_RO macro
mfd: ucb1x00-assabet: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEFINE_RES_IRQ_NAMED() and DEFINE_RES_IRQ() to simplify code
dt-bindings: mfd: stm32-timers: Remove #address/size cells from required properties
mfd: sun6i-prcm: Use DEFINE_RES_MEM() to simplify code
mfd: asic3: Use DEFINE_RES_MEM() and DEFINE_RES_IRQ() to simplify code
mfd: 88pm805: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: 88pm800: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: tps80031: Use DEFINE_RES_IRQ() to simplify code
mfd: da9055: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: as3722: Use DEFINE_RES_IRQ_NAMED() to simplify code
...
Pull sound updates from Takashi Iwai:
"As the diffstat scatters over the tree, we've got many tree-wide small
changes, but also got quite a few intrusive changes in the core side.
The only ABI-visible core change is the new rawmidi framing mode
support while others are kernel-internal, mostly code refactoring
and/or nice improvements.
Here are some highlights:
Core:
- A new framing access mode for rawmidi to get timestamps
- Cleanup / refactoring of buffer memory management helper code
- Support for automatic negotiation of ASoC DAI formats
- Revival of software suspend for PCM and control core, as a
preliminary work for PCI BAR rescan support
ASoC:
- Accessory detection support for several Qualcomm parts
- Support for IEC958 control with hdmi-codec
- Merging of Tegra machine drivers into a single driver
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
USB-audio:
- Reduction of latency at playback start
- Code cleanup / fixes of usx2y driver
- Scarlett2 mixer code fixes and enhancements
- Quirks for Ozone and Denon devices
HD-audio:
- A few quirks for HP and ASUS machines
- Display power management fixes
Others:
- FireWire code refactoring and enhancements
- Tree-wide trivial coding-style fixes"
* tag 'sound-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: usb-audio: scarlett2: Fix for loop increment in scarlett2_usb_get_config
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 630 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 445 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 450 G8
ALSA: hda/realtek - Add ALC285 HP init procedure
ALSA: hda/realtek - Add type for ALC287
ALSA: scarlett2: Fix scarlett2_*_ctl_put() return values again
ALSA: scarlett2: Fix pad count for 18i8 Gen 3
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 830 G8 Notebook PC
ALSA: firewire-lib: Fix 'amdtp_domain_start()' when no AMDTP_OUT_STREAM stream is found
ASoC: qcom: lpass-cpu: mark IRQ_CLEAR register as volatile and readable
ALSA: hda: Release codec display power during shutdown/reboot
ALSA: hda: Release controller display power during shutdown/reboot
ALSA: hda/realtek: Apply LED fixup for HP Dragonfly G1, too
ASoC: fsl: remove unnecessary oom message
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tegra30: ahub: Use devm_platform_get_and_ioremap_resource()
ASoC: tegra: tegra210_admaif: Use devm_platform_get_and_ioremap_resource()
...
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- New think-lmi driver adding support for changing Lenovo Thinkpad
BIOS settings from within Linux using the standard firmware-
attributes class sysfs API
- MS Surface aggregator-cdev now also supports forwarding events to
user-space (for debugging / new driver development purposes only)
- New intel_skl_int3472 driver this provides the necessary glue to
translate ACPI table information to GPIOs, regulators, etc. for
camera sensors on Intel devices with IPU3 attached MIPI cameras
- A whole bunch of other fixes + device-specific quirk additions
- New devm_work_autocancel() devm-helpers.h function"
* tag 'platform-drivers-x86-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (83 commits)
platform/x86: dell-wmi-sysman: Change user experience when Admin/System Password is modified
platform/x86: intel_skl_int3472: Uninitialized variable in skl_int3472_handle_gpio_resources()
platform/x86: think-lmi: Move kfree(setting->possible_values) to tlmi_attr_setting_release()
platform/x86: think-lmi: Split current_value to reflect only the value
platform/x86: think-lmi: Fix issues with duplicate attributes
platform/x86: think-lmi: Return EINVAL when kbdlang gets set to a 0 length string
platform/x86: intel_cht_int33fe: Move to its own subfolder
platform/x86: intel_skl_int3472: Move to intel/ subfolder
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_regulator()
platform/x86: intel_skl_int3472: Use ACPI GPIO resource directly
platform/x86: intel_skl_int3472: Fix dependencies (drop CLKDEV_LOOKUP)
platform/x86: intel_skl_int3472: Free ACPI device resources after use
platform/x86: Remove "default n" entries
platform/x86: ISST: Use numa node id for cpu pci dev mapping
platform/x86: ISST: Optimize CPU to PCI device mapping
tools/power/x86/intel-speed-select: v1.10 release
tools/power/x86/intel-speed-select: Fix uncore memory frequency display
extcon: extcon-max8997: Simplify driver using devm
extcon: extcon-max8997: Fix IRQ freeing at error path
...
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
This patch adds a cell entry for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
IRQF_NO_AUTOEN flag doesn't go well with IRQF_SHARED flag - the
check in request_threaded_irq fails and exits with EINVAL.
So we ignore the flag and enable it on the first IRQ request. No
interrupt should arrive from the chip as all interrupts are masked
by default.
Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO/RW macro helper instead of plain DEVICE_ATTR, which
makes the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_ADMIN_RW macro helper instead of plain DEVICE_ATTR, which
makes the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO macro helper instead of plain DEVICE_ATTR, which makes
the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO macro helper instead of plain DEVICE_ATTR, which makes
the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_ADMIN_RO macro helper instead of plain DEVICE_ATTR, which
makes the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO macro helper instead of plain DEVICE_ATTR, which makes
the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO macro helper instead of plain DEVICE_ATTR, which makes
the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use DEVICE_ATTR_RO macro helper instead of plain DEVICE_ATTR, which makes
the code a bit shorter and easier to read.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver include linux/irqdomain.h via a bizarre set of
indirection, which we are about to break.
Directly include the required file.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The pixel lightbar is only present on chromebook pixel (link), pixel 2
and pixel C. For the latter two, the EC reports its presence.
Instead of always loading the lightbar driver on all chromebook, only
load it when reported by the EC or Link device.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Set device wakeup capability from devicetree property (done by drivers
core), instead of always setting it to 0 (because value in platform data
is not assigned).
This should not have visible effect on actual resuming from suspend
because the child device - S5M RTC driver - is responsible for waking
up and sets device wakeup unconditionally.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 'irq_base' field of platform data structure is not assigned,
therefore its default value of 0 has no impact and can be safely
dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Samsung PMIC drivers since long time are used only on devicetree
platforms (Samsung Exynos) and there are no users with board files.
Drop the support for board files entirely and depend on OF for matching.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller. There
is also no need to wrap it in a check for CONFIG_OF, because dev.of_node
will be set only with OF support.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller. There
is also no need to wrap it in a check for CONFIG_OF, because dev.of_node
will be set only with OF support.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller. There
is also no need to wrap it in a check for CONFIG_OF, because dev.of_node
will be set only with OF support.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Qualcomm Technologies, Inc. PM8008 is a dedicated camera PMIC that
integrates all the necessary power management, housekeeping, and
interface support functions into a single IC. Its key features include
overtemperature protection, low-dropout linear regulators, GPIOs, and an
I2C interface.
Add an MFD driver to support it.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have started to get a bunch of pointless dmamask not set warnings
that makes the output of dmesg -l err,warn hard to read with many
extra warnings:
cpcap-regulator cpcap-regulator.0: DMA mask not set
cpcap_adc cpcap_adc.0: DMA mask not set
cpcap_battery cpcap_battery.0: DMA mask not set
cpcap-charger cpcap-charger.0: DMA mask not set
cpcap-pwrbutton cpcap-pwrbutton.0: DMA mask not set
cpcap-led cpcap-led.0: DMA mask not set
cpcap-led cpcap-led.1: DMA mask not set
cpcap-led cpcap-led.2: DMA mask not set
cpcap-led cpcap-led.3: DMA mask not set
cpcap-led cpcap-led.4: DMA mask not set
cpcap-rtc cpcap-rtc.0: DMA mask not set
cpcap-usb-phy cpcap-usb-phy.0: DMA mask not set
This seems to have started with commit 4d8bde883b ("OF: Don't set
default coherent DMA mask"). We have the parent SPI controller use
DMA, while CPCAP driver and it's children do not. For audio, the
DMA is handled over I2S bus with the McBSP driver.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no reason why the arizona core,irq and codec model specific
regmap bits cannot be build as a module. All they do is export symbols
which are used by the arizona-spi/i2c and arizona-codec modules, which
themselves can be built as module.
Change the Kconfig and Makefile arizona bits so that the arizona MFD-core
can be built as a module.
This is especially useful on x86 platforms with a WM5102 codec, this
allows the arizona MFD driver necessary for the WM5102 codec to be
enabled in generic distro-kernels without growing the base kernel-image
size.
Note this also adds an explicit "depends on MFD_ARIZONA" to all the
arizona codec Kconfig options. The codec drivers use functions from mfd
arizona-core. These new depends are necessary to disallow the codec
drivers being builtin when the arizona-core is build as a module,
otherwise we end up with missing symbol errors when building vmlinuz.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/mfd/si476x-i2c.c:360: warning: expecting prototype for si476x_drain_rds_fifo(). Prototype was for si476x_core_drain_rds_fifo() instead
drivers/mfd/si476x-i2c.c:467: warning: expecting prototype for si476x_get_status(). Prototype was for si476x_core_get_status() instead
drivers/mfd/si476x-i2c.c:484: warning: expecting prototype for si476x_get_and_signal_status(). Prototype was for si476x_core_get_and_signal_status() instead
drivers/mfd/si476x-i2c.c:555: warning: expecting prototype for si476x_firmware_version_to_revision(). Prototype was for si476x_core_fwver_to_revision() instead
drivers/mfd/si476x-i2c.c:619: warning: expecting prototype for si476x_get_revision_info(). Prototype was for si476x_core_get_revision_info() instead
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
