The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control
as 1/16th of a line. This is what the sensor expects, but isn't very
intuitive. Switch the control to be in units of a line and simply do the
16x multiplication before passing the value to the sensor.
The datasheet for this sensor gives minimum exposure as 2 lines, so take
the opportunity to correct the lower bounds of the control.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure limits depend on the total height; when vblank is altered (and
thus the total height is altered), change the exposure limits to reflect
the new cap.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HTS values for some of the modes in the ov8865 driver are a bit
unusual, coming in lower than the output_size_x is set to. It seems
like they might be calculated to fit the desired framerate into a
configuration with just two data lanes. To bring this more in line
with expected behaviour, raise the HTS values above the output_size_x.
The corollary of that change is that the hardcoded frame intervals
against the modes no longer make sense, so remove those entirely.
Update the .g/s_frame_interval() callbacks to calculate the frame
interval based on the current mode and the vblank and hblank settings.
The implementation of the .enum_frame_interval() callback is no longer
suitable since the possible frame rate is now a continuous range depending
on the vblank control setting, so remove that callback entirely.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only
with timing control intended to be done via vblanking alone.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver's v4l2_subdev_pad_ops currently does not include
.get_selection() - add support for that callback.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver as written expects a 24MHz input clock, but the sensor
is sometimes found on x86 platforms with a 19.2MHz input clock supplied.
Add a set of PLL configurations to the driver to support that rate too.
As ACPI doesn't auto-configure the clock rate, check for a clock-frequency
during probe and set that rate if one is found.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver is one of those that can be connected to a CIO2
device by the cio2-bridge code. This means that the absence of an
endpoint for this device is not necessarily fatal, as one might be
built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no
endpoint is found rather than a fatal error.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI.
Add an ACPI match table to the driver so that it's probed on those
platforms.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5693 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2. The
chip is capable of a single lane configuration, but currently only two
lanes are supported.
Most of the sensor's features are supported, with the main exception
being the lens correction algorithm.
The driver provides all mandatory, optional and recommended V4L2 controls
for maximum compatibility with libcamera.
[mchehab: fixed a coding style warning]
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Current driver supports only SRGGB 10 bit RAW bayer format.
Add the enum_mbus_code implementation to report this format supported.
# v4l2-ctl -d /dev/v4l-subdev3 --list-subdev-mbus-codes
ioctl: VIDIOC_SUBDEV_ENUM_MBUS_CODE (pad=0)
0x300f: MEDIA_BUS_FMT_SRGGB10_1X10
#
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 has not explicitly declared a dependency upon VIDEO_V4L2.
While this dependency has likely always been met by configurations
including it, the device does use V4L2 core, and should depend upon it.
Add VIDEO_V4L2 as a dependency to match other drivers and prevent
failures when compile testing.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those are aliases for another function and not used at the
current implementation. So, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those functions just call a V4L2 core macro, and aren't used
anywhere. Get rid of them, in order to avoid clang warnings with
W=1.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Solve some clang warnings about unused functions by dropping
some time-conversion inline funcs that aren't used anywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Pull media fixes from Mauro Carvalho Chehab:
- fix VIDIOC_DQEVENT ioctl handling for 32-bit userspace with a 64-bit
kernel
- regression fix for videobuf2 core
- fix for CEC core when handling non-block transmit
- hi846: fix a clang warning
* tag 'media/v5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hi846: remove the of_match_ptr macro
media: hi846: include property.h instead of of_graph.h
media: cec: copy sequence field for the reply
media: videobuf2-dma-sg: Fix buf->vb NULL pointer dereference
media: v4l2-core: fix VIDIOC_DQEVENT handling on non-x86
Similar to other drivers, this should fix a Clang compilar warning when
building without CONFIG_OF in which case of_match_ptr() is NULL and
the const struct we would use otherwise is unused.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When dw9768 working with ACPI systems, the dw9768 was turned
by i2c-core during probe, driver need activate the PM runtime
and ask runtime PM to turn off the device.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
show() should not use snprintf() when formatting the value to be
returned to user space.
Fix the following coccicheck warning:
drivers/media/i2c/ccs/ccs-core.c:3761: WARNING: use scnprintf or sprintf.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611.
Also: print chip names in upper case.
Fix an error message claiming that no ADV761x has been found,
while in reality a chip different than requested (though still
supported) may have been found.
Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TDA1997x (HDMI receiver) driver currently uses a specific video
format detection scheme. The frame (or field in interlaced mode), line
and HSync pulse durations are compared to those of known, standard video
modes. If a match is found, the mode is assumed to be detected,
otherwise -ERANGE is returned (then possibly ignored). This means that:
- another mode with similar timings will be detected incorrectly
(e.g. 2x faster clock and lines twice as long)
- non-standard modes will not work.
This patch replaces this scheme with a direct read of geometry
registers. This way all modes recognized by the chip are supported.
In interlaced modes, the code assumes the V sync signal has the same
duration for both fields. While this may be not necessarily true,
I can't see any way to get the "other" V sync width. This is most
probably harmless.
All tests have been performed on Gateworks' Ventana GW54xx board, with
a TDA19971 chip.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I came across a link failure from randconfig builds:
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove':
tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe':
tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev'
These clearly lack a 'select' statement, but I don't know why
this started happening only now. I had a bit of a look around to find
other configs that have the same problem, but could not come up with
a reliable way and found nothing else through experimentation.
It is likely that other symbols like these exist that need an extra
select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the build errors reported by the kernel test robot by
selecting V4L2_ASYNC:
mips-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x1ec): undefined reference to `v4l2_async_unregister_subdev'
mips-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0x404): undefined reference to `v4l2_async_register_subdev'
Fixes: ed29f89497 ("media: i2c: ths8200: support asynchronous probing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MLX90640 should ideally be working without a frame skip.
In short, if a frame is skipped, then half of a frame loses correction
information, having no way to retrieve its original compensation.
This patch improves the timing in three ways:
1) Replaced schedule_timeout_interruptible() to usleep_range()
The former "only ensures that it will sleep for at least
schedule_delay (if not interrupted)", as pointed out by mchehab.
As a result, the frame rate could lag behind than the actual capability
of the hardware
(Raspberry Pi would show a few Hz slower than set value)
2) Calculation based on us, not jiffies
Jiffies usually has resolution of 100Hz, and possibly even cruder.
MLX90640 can go up to 64Hz frame rate, which does not make sense to
calculate the interval with aforementioned resolution.
3) Interval calculation based on the last frame's end time
Using the start time of the current frame will probably make tiny bit
of drift every time. This made more sense when I didn't realize 1),
but it still makes sense without adding virtually any complexity,
so this stays in.
Signed-off-by: Seongyong Park <euphoriccatface@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Static analysis reports this representative problem
tda1997x.c:1939: warning: 7th function call argument is an uninitialized
value
The 7th argument is buffer[0], which is set in the earlier call to
io_readn(). When io_readn() call to io_read() fails with the first
read, buffer[0] is not set and 0 is returned and stored in len.
The later call to hdmi_infoframe_unpack()'s size parameter is the
static size of buffer, always 40, so a short read is not caught
in hdmi_infoframe_unpacks()'s checking. The variable len should be
used instead.
Zero initialize buffer to 0 so it is in a known start state.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting the value of V_WIN_OFF (0x3818) from 0x02 to 0x01 to use GRBG
format still results in wrong color output if data is tuned in BGGR mode
before.
Set default mbus format for the supported modes, but allow the caller of
set(get)_fmt to change the bayer format between BGGR and GRBG.
Set the default mbus format for 3264x2448 (and 1632x1224) to BGGR as the
data sheet states the value of this reg should be 0x02 by default.
If new modes are added in the future, they can add the
mipi_data_mbus_{format} settings into bayer_offset_configs to adjust their
offset regs.
Fixes: 2984b0ddd5 ("media: ov8856: Configure sensor for GRBG Bayer for all modes")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver supports following features:
- phase detection auto focus (PDAF)
- manual exposure and analog/digital gain control
- vblank/hblank control
- test pattern
- image vertical flip and horizontal mirror control
- 4208x3120 at 30FPS
- 2080x1170 at 60FPS
Signed-off-by: Arec Kao <arec.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Obtain the clock frequency by reading the clock-frequency property if
there's no clock.
Fixes: 9fda25332c ("media: i2c: imx258: get clock from device properties and enable it via runtime PM")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TDA1997x driver tried to hold two values in a single variable:
device's "client data" pointer was first set to "sd" in
v4l2_i2c_subdev_init(), then it was overwritten explicitly
using dev_set_drvdata() with "state". This caused
tda1997x_remove() to fail badly.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of the BIT macro for setting individual bits. This improves
readability and safety with respect to shifts.
When on it also remove two zero value disable defines.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
