Set the maximum ABS_MT_PRESSURE value and use the existing U16_MAX
definition instead of a magic number to validate ABS_MT_POSITION_X
and ABS_MT_POSITION_Y.
Also use input_set_abs_params() rather than input_abs_set_max() to
avoid having to call input_set_capability() separately.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-3-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to datasheets, chips like mXT1386 have a WAKE line, it is used
to wake the chip up from deep sleep mode before communicating with it via
the I2C-compatible interface.
If the WAKE line is connected to a GPIO line, the line must be asserted
25 ms before the host attempts to communicate with the controller. If the
WAKE line is connected to the SCL pin, the controller will send a NACK on
the first attempt to address it, the host must then retry 25 ms later.
Implement the wake-up methods in the driver. Touchscreen now works
properly on devices like Acer A500 tablet, fixing problems like this:
atmel_mxt_ts 0-004c: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts 0-004c: mxt_bootloader_read: i2c recv failed (-121)
atmel_mxt_ts 0-004c: Trying alternate bootloader address
atmel_mxt_ts 0-004c: mxt_bootloader_read: i2c recv failed (-121)
atmel_mxt_ts: probe of 0-004c failed with error -121
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210302102158.10533-3-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Split out the multitouch event handling into its own function to allow other
events to be handled in the IRQ handler without disturbing the MT handling.
Now that things are separated a bit more, stop treating vendor data requests
special by cehcking for a locked mutex, but just look at the event ID to
figure out if the message is a MT report or a vendor data query reply.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20210125182527.1225245-2-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touch coordinate register contains the following:
byte 3 byte 2 byte 1
+--------+--------+ +-----------------+ +-----------------+
| | | | | | |
| X[3:0] | Y[3:0] | | Y[11:4] | | X[11:4] |
| | | | | | |
+--------+--------+ +-----------------+ +-----------------+
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Mostly existing driver fixes plus a new driver for game controllers
directly connected to Nintendo 64, and an enhancement for keyboards
driven by Chrome OS EC to communicate layout of the top row to
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (47 commits)
Input: st1232 - fix NORMAL vs. IDLE state handling
Input: aiptek - convert sysfs sprintf/snprintf family to sysfs_emit
Input: alps - fix spelling of "positive"
ARM: dts: cros-ec-keyboard: Use keymap macros
dt-bindings: input: Fix the keymap for LOCK key
dt-bindings: input: Create macros for cros-ec keymap
Input: cros-ec-keyb - expose function row physical map to userspace
dt-bindings: input: cros-ec-keyb: Add a new property describing top row
Input: applespi - fix occasional crc errors under load.
Input: applespi - don't wait for responses to commands indefinitely.
Input: st1232 - add IDLE state as ready condition
Input: zinitix - fix return type of zinitix_init_touch()
Input: i8042 - add ASUS Zenbook Flip to noselftest list
Input: add missing dependencies on CONFIG_HAS_IOMEM
Input: joydev - prevent potential read overflow in ioctl
Input: elo - fix an error code in elo_connect()
Input: xpad - add support for PowerA Enhanced Wired Controller for Xbox Series X|S
Input: sur40 - fix an error code in sur40_probe()
Input: elants_i2c - detect enum overflow
Input: zinitix - remove unneeded semicolon
...
The st1232 can switch from NORMAL to IDLE state after the configured
idle time (by default 8 s). If the st1232 is not reset during probe, it
might already be ready but in IDLE state. Since it does not enter NORMAL
state in this case, probe fails.
Fix the wait function to report the IDLE state as ready, too.
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210219110556.1858969-1-m.tretter@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ASoC: Updates for v5.12
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
If an enum value were to get added without updating this switch
statement, the unreachable() annotation would trigger undefined
behavior, causing execution to fall through the end of the function,
into the next one.
Make the error handling more robust for an unexpected enum value, by
doing BUG() instead of unreachable().
Fixes the following objtool warning:
drivers/input/touchscreen/elants_i2c.o: warning: objtool: elants_i2c_initialize() falls through to next function elants_i2c_resume()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/59e2e82d1e40df11ab38874c03556a31c6b2f484.1612974132.git.jpoimboe@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After the device is initialized, it runs ATI (calibration) during
which it cannot readily respond to I2C communication. To keep the
open and close callbacks from writing to the device too soon, the
driver waits 100 ms before returning from probe.
The vendor reports that ATI may actually take up to 250 ms to run
(including margin), so increase the delay accordingly. Update the
comments to clarify the reason for the delay as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-9-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of relying on firmware to enable important register fields
and performing read-modify-write operations to additionally enable
the fields the driver cares about, it's much simpler just to write
all of the pertinent fields explicitly.
This avoids an unnecessary register read operation at start-up and
makes way for the iqs5xx_read_byte() helper to be dropped.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-8-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The present implementation manipulates axis swap and inversion fields
in the device to more or less duplicate what touchscreen_report_pos()
does. The resulting logic is convoluted and difficult to follow.
Instead report the maximum X and Y coordinates in earnest as they are
read from the device, then let touchscreen_parse_properties() fix the
axes up as necessary. Finally, use touchscreen_report_pos() to report
the transformed coordinates.
Last but not least, the maximum X and Y coordinates are not functions
of the number of rows/columns that comprise the touch surface. Either
coordinate is simply limited to 1 below what is reported for absolute
X or Y coordinates when no fingers are present (0xFFFF).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-7-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device may be inadvertently reset during runtime in the event
of ESD strike, etc. To protect against this case, acknowledge the
SHOW_RESET interrupt and re-initialize the device.
To facilitate this change, expand the range of registers that are
read in the interrupt handler to include the system status fields.
Also, update the unrelated (but nearby) SUSPEND register field to
use the BIT() macro. The remaining register fields are cleaned up
in another patch.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-6-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bootloader NAK's all I2C communication after the first 64-byte
bulk write if the bus frequency is equal to 400 kHz. This prevents
the platform from pushing updated firmware to the device.
The vendor's USB bootloader programming dongle appears to insert a
delay between the "open" command and the first 64-byte bulk write.
Adding a similar delay to the driver seems to eliminate the issue.
Furthermore, the dongle does not access the bootloader immediately
after powering up the device. Follow suit by adding a delay before
the "open" command to avoid wasted retries at 400 kHz.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-4-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After user space writes the fw_file attribute to push new firmware
to the device, the driver calls iqs5xx_dev_init() to re-initialize
the device with the updated firmware or recover the device in case
the update failed.
In the case of the latter, however, iqs5xx_fw_file_write() returns
zero (success) so long as iqs5xx_dev_init() does not fail, and any
error encountered during the update process is lost. Solve this by
saving the error before calling iqs5xx_dev_init().
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-3-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyrights are generally followed by the name of a person or a
company (i.e. the copyright holder) but that was not done here.
Fix this by squashing the 'copyright' and 'author' lines.
Also, trim some leading whitespace ahead of the parameters for
the fw_file_store() function and re-align them for readability.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-2-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN KTF3624 touchscreen support to the elants_i2c driver.
The eKTF3624 TS is found on a series of ASUS Transformer tablet devices,
Nexus 7 tablet and etc. The firmware interface of eKTF3624 is nearly
identical to eKTH3500, which is already supported by the driver.
The minor differences of the firmware interface are now handled by
the driver. The eKTF3624 support was tested on ASUS Transformer TF700T,
TF300T and Nexus 7 tablets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210124195414.27333-1-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert multiple full duplex transfers in to a single transfer to reduce
CPU load.
Current driver version support following filtering modes:
- ads7846_no_filter() - not filtered
- ads7846_debounce_filter() - driver specific debounce filter
- pdata->filter - platform specific debounce filter (do any platform
provides such filter?)
Without filter this HW is not really usable, since the physic of
resistive touchscreen can provide some bounce effects. With driver internal
filter, we have constant amount of retries + debounce retries if some anomaly
was detected.
High amount of tiny SPI transfers is the primer reason of high CPU load
and interrupt frequency.
This patch create one SPI transfer with all fields and not optional retires. If
bounce anomaly was detected, we will make more transfer if needed.
Without this patch, we will get about 10% CPU load on iMX6S on pen-down event.
For example by holding stylus on the screen.
With this patch, depending in the amount of retries, the CPU load will
be 1% with "ti,debounce-rep = <3>".
One buffer transfer allows us to use PIO FIFO or DMA engine, depending
on the platform.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-3-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry requested to keep these around for the purposes of documentation.
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/melfas_mip4.c: In function ‘mip4_report_touch’:
drivers/input/touchscreen/melfas_mip4.c:474:5: warning: variable ‘size’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:472:5: warning: variable ‘pressure_stage’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:469:7: warning: variable ‘palm’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:468:7: warning: variable ‘hover’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.
If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution. However, the latter may
happen before the device is ready, leading to a probe failure:
st1232-ts 1-0055: Failed to read resolution: -6
Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.
On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller. This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.
Optimize transfers by passing the wanted number of bytes.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type. The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).
Fix this by subtracting 1.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
Pull spi updates from Mark Brown:
"The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and
driver data together.
Together with some of the other work done it feels like we've turned
the corner on several long standing pain points with the API.
Summary:
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured
by drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO
level chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler
Lake"
* tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors
spi: Limit the spi device max speed to controller's max speed
spi: spi-geni-qcom: Use the new method of gpio CS control
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
spi: dw: Add support for the Canaan K210 SoC SPI
spi: dw: Add support for 32-bits max xfer size
dt-bindings: spi: dw-apb-ssi: Add Canaan K210 SPI controller
spi: Update DT binding docs to support SiFive FU740 SoC
spi: atmel-quadspi: Fix use-after-free on unbind
spi: npcm-fiu: Disable clock in probe error path
spi: ar934x: Don't leak SPI master in probe error path
spi: mt7621: Don't leak SPI master in probe error path
spi: mt7621: Disable clock in probe error path
media: netup_unidvb: Don't leak SPI master in probe error path
spi: sc18is602: Don't leak SPI master in probe error path
spi: rb4xx: Don't leak SPI master in probe error path
spi: gpio: Don't leak SPI master in probe error path
spi: spi-mtk-nor: Don't leak SPI master in probe error path
spi: mxic: Don't leak SPI master in probe error path
...
