Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some pmbus device drivers have device tree support and
may want to use of-thermal to register a thermal zone
OF sensor for those device drivers.
This way we allow describing device tree thermal zones
for pmbus device drivers with device tree support.
This patch achieves this by registering pmbus sensors
with thermal subsystem if they are PSC_TEMPERATURE
and are providing _input hwmon interface.
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:PMBUS HARDWARE MONITORING DRIVERS)
Cc: Jean Delvare <jdelvare@suse.com> (maintainer:HARDWARE MONITORING)
Cc: linux-hwmon@vger.kernel.org (open list:PMBUS HARDWARE MONITORING DRIVERS)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Link: https://lore.kernel.org/r/20220428174926.2150-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the manuals for devices supported by this driver describes
the need for a minimum wait time before the chip is ready to receive
next command.
This wait time is already implemented in the driver as a ltc_wait_ready
function with a driver defined wait time of 100 ms, and is considered
for specific devices before reading/writing data on the pmbus.
Since this driver uses the default pmbus_regulator_ops for the enable/
disable/is_enabled functions we should add a driver specific callback
for write_byte_data to prevent bypassing the wait time recommendations
for the following devices: ltc3880/ltc3882/ltc3883/ltc3884/ltc3886/
ltc3887/ltc3889/ltm4664/ltm4675/ltm4676/ltm4677/ltm4678/ltm4680/ltm4686/
ltm4700/ltc7880.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-4-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_read_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets use _pmbus_read_byte_data with callback check.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_write_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets add support for driver callback with _pmbus_write_byte_data.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another MAX16602 chip support to MAX16601 driver
Tested with MAX16602 works as expected.
Signed-off-by: Atif Ofluoglu <atif.ofluoglu@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day reports:
drivers/hwmon/pmbus/xdpe12284.c:127:36: warning:
unused variable 'xdpe122_reg_desc'
This is seen if CONFIG_SENSORS_XDPE122_REGULATOR is not enabled.
Mark xdpe122_reg_desc as __maybe_unused to fix the problem.
Fixes: f53bfe4d69 ("hwmon: (xdpe12284) Add regulator support")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current driver assume PWR_AVG and VI_AVG as 1 by default, and user needs
to set sample averaging via sysfs manually.
This patch parses the properties "adi,power-sample-average" and
"adi,volt-curr-sample-average" from device tree, and setting sample
averaging during probe. Input value must be one of value in the
list [1, 2, 4, 8, 16, 32, 64, 128].
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Link: https://lore.kernel.org/r/20220302123817.27025-2-potin.lai@quantatw.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While these chips aren't strictly advertised as voltage regulators per
se, they (aside from the lm25056) support the PMBus OPERATION command
to enable and disable their outputs and have status bits for reporting
various warnings and faults, and can hence usefully support all the
pmbus_regulator_ops operations.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220219000742.20126-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_PM is not enabled, the following warning is reported.
drivers/hwmon/pmbus/ir38064.c:54:34: warning:
unused variable 'ir38064_of_match'
Mark it as __maybe_unused.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arthur Heymans <arthur.heymans@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This device is an integrated module of the Delta AHE-50DC Open19 power
shelf. I haven't been able to procure any proper documentation for
it, but it seems to be a (somewhat minimally) PMBus-compliant device.
It provides four fan speeds, four temperatures (three standard and one
manufacturer-specific via a virtual second page), and a vin reading.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20211208213703.2577-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The appropriate mantissa values for the lm25066 family's direct-format
current and power readings are a function of the sense resistor
employed between the SENSE and VIN pins of the chip. Instead of
assuming that resistance is always the same 1mOhm as used in the
datasheet, allow it to be configured via a device-tree property
("shunt-resistor-micro-ohms").
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-8-zev@bewilderbeest.net
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-7-zev@bewilderbeest.net
[groeck: Replaced reference to reasoning with reasoning, fixed checkpatch
warnings, fixed compile warning comparing of_id->data w/ i2c_id->driver_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the initial implementation a number of PMBUS_x_WARN_LIMITs were
mapped to MFR fields. This was incorrect as these MFR limits reflect the
rated limit as opposed to a limit which will generate warning. Instead
return -ENXIO like we were already doing for other WARN_LIMITs.
Subsequently these rated limits have been exposed generically as new
fields in the sysfs ABI so the values are still available.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs_create_dir() function returns error pointers, it doesn't
return NULL. But debugfs functions don't need to be checked in normal
situations and we can just delete this code.
Fixes: 1f442e213ce5 ("hwmon: (pmbus) Add driver for Delta DPS-920AB PSU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YMyjmR54ErLtc1sH@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for Flex power interface modules PIM4006,
PIM4328 and PIM4820.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow the use of a phase function even if it does not exist on
the associated page.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading and decoding direct format coefficients to
the PMBus core driver. If the new flag PMBUS_USE_COEFFICIENTS_CMD
is set, the driver will use the COEFFICIENTS register together with
the information in the pmbus_sensor_attr structs to initialize
relevant coefficients for the direct mode format.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
[groeck: Initialize ret with -EINVAL in pmbus_init_coefficients()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
