The DSI version of the panel behaved instable and close
scrutiny of the vendor driver from the Samsung
GT-S8190 shows a different initialization sequence for
the DSI mode panel than the DPI mode panel.
Make the initialization depend on whether we are in
DSI or DPI mode and handle the differences.
After this the panel on the GT-I8190 becomes much more
stable.
Also spell out some more custom DCS commands found in
the vendor source code to cut down a bit on magic
where we can.
Fixes: f0aee45ffc ("drm/panel: s6e63m0: Fix init sequence")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205122229.1952980-1-linus.walleij@linaro.org
The init sequence consist of a number of unknown settings
for the display controller. This patch achieves two things:
- Fix an error that must have happened when the driver was
converted from the backlight subsystem: the 0xb8
configuration command was lost and added as a tail to
the previous command.
- Update some minor settings in some bytes here and there
according to changes in the Samsung GT-I9070 and
Samsung GT-S7710 code dumps. Since two other devices use
these settings they probably reflect trimmings later
found to be better for the display rather than
customizations for these devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117175621.870085-3-linus.walleij@linaro.org
Copy over the width/height in millimeters to the
(somewhat redundant) display info, and set up the
bus format and bus flags for the display.
When used as DPI this display requires DE to be
active low and pixel data to be output on the
negative edge. It might be that it was previously
used with a display controller that either does
not support these settings or was hardcoded to use
these as default. This information comes from the
source code of the Samsung GT-I9070 mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110234653.2248594-6-linus.walleij@linaro.org
The upstream S6E63M0 driver has some peculiarities around
the prepare/enable disable/unprepare sequence: the screen
is taken out of sleep in prepare() as part of
s6e63m0_init() the put to on with MIPI_DCS_SET_DISPLAY_ON
in enable().
However it is just put into sleep mode directly in
disable(). As disable()/enable() can be called without
unprepare()/prepare() being called, this is unbalanced,
we should take the display out of sleep in enable()
then turn it off().
Further MIPI_DCS_SET_DISPLAY_OFF is never called
balanced with MIPI_DCS_SET_DISPLAY_ON.
The vendor driver for Samsung GT-I8190 (Golden) does all
of these things in strict order.
Augment the driver to do exit sleep/set display on in
enable() and set display off/enter sleep in disable().
Further send an explicit reset pulse in power_on() so we
come up in a known state, and issue the MCS_ERROR_CHECK
command after setting display on like the vendor driver
does. Also use the timings from the vendor driver in
the sequence.
Doing all of these things makes the display much more
stable on the Samsung GT-I8190 when enabling/disabling
the display pipeline.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200817213906.88207-1-linus.walleij@linaro.org
This panel can be accessed using both SPI and DSI.
To make it possible to probe and use the device also from
a DSI bus, first break out the SPI support to its own file.
Since all the panel driver does is write DCS commands to
the panel, we pass a DCS write function to probe()
from each subdriver.
We make the Kconfig entry for SPI mode default so all
current users will continue to work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/384873/
Add a type field to the drm_panel structure to report the panel type,
using DRM_MODE_CONNECTOR_* macros (the values that make sense are LVDS,
eDP, DSI and DPI). This will be used to initialise the corresponding
connector type.
Update all panel drivers accordingly. The panel-simple driver only
specifies the type for the known to be LVDS panels, while all other
panels are left as unknown and will be converted on a case-by-case
basis as they all need to be carefully reviewed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-2-laurent.pinchart@ideasonboard.com
Instead of requiring all drivers to set the dev and funcs fields of
drm_panel manually after calling drm_panel_init(), pass the data as
arguments to the function. This simplifies the panel drivers, and will
help future refactoring when adding new arguments to drm_panel_init().
The panel drivers have been updated with the following Coccinelle
semantic patch, with manual inspection to verify that no call to
drm_panel_init() with a single argument still exists.
@@
expression panel;
expression device;
identifier ops;
@@
drm_panel_init(&panel
+ , device, &ops
);
...
(
-panel.dev = device;
-panel.funcs = &ops;
|
-panel.funcs = &ops;
-panel.dev = device;
)
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823193245.23876-3-laurent.pinchart@ideasonboard.com
