The VBT send packet port selection was never updated for ICL+ where the
2nd link is on port B instead of port C as in VLV+ DSI.
First, single link DSI needs to use the configured port instead of
relying on the VBT sequence block port. Remove the hard-coded port C
check here and make it generic. For reference, see commit f915084edc
("drm/i915: Changes related to the sequence port no for") for the
original VLV specific fix.
Second, the sequence block port number is either 0 or 1, where 1
indicates the 2nd link. Remove the hard-coded port C here for 2nd
link. (This could be a "find second set bit" on DSI ports, but just
check the two possible options.)
Third, sanity check the result with a warning to avoid a NULL pointer
dereference.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5984
Cc: stable@vger.kernel.org # v4.19+
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520094600.2066945-1-jani.nikula@intel.com
(cherry picked from commit 08c59dde71)
The VBT DSI video transfer mode field values have been defined in terms
of the VLV MIPI_VIDEO_MODE_FORMAT register. The ICL DSI code maps that
to ICL DSI_TRANS_FUNC_CONF() register. The values are the same, though
the shift is different.
Make a clean break and disassociate the values from each other. Assume
the values can be different, and translate the VBT value to VLV and ICL
register values as needed. Use the existing macros from intel_bios.h.
This will be useful in splitting the DSI register macros to files by DSI
implementation.
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217224023.3994777-1-jani.nikula@intel.com
Several of our i915 header files, have been including i915_reg.h. This
means that any change to i915_reg.h will trigger a full rebuild of
pretty much every file of the driver, even those that don't have any
kind of register access. Let's delete the i915_reg.h include from all
headers and add an explicit include from the .c files that truly
need the register definitions; those that need a definition of
i915_reg_t for a function definition can get it from i915_reg_defs.h
instead.
We also remove two non-register #define's (VLV_DISPLAY_BASE and
GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the
i915_reg.h include from a couple of headers.
There's probably a lot more header dependency optimization possible, but
the changes here roughly cut the number of files compiled after 'touch
i915_reg.h' in half --- a good first step.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
On Bay Trail devices the MIPI power on/off sequences for DSI LCD panels
do not control the LCD panel- and backlight-enable GPIOs. So far, when
the VBT indicates we should use the SoC for backlight control, we have
been relying on these GPIOs being configured as output and driven high by
the Video BIOS (GOP) when it initializes the panel.
This does not work when the device is booted with a HDMI monitor connected
as then the GOP will initialize the HDMI instead of the panel, leaving the
panel black, even though the i915 driver tries to output an image to it.
Likewise on some device-models when the GOP does not initialize the DSI
panel it also leaves the mux of the PWM0 pin in generic GPIO mode instead
of muxing it to the PWM controller.
This commit makes the DSI code control the SoC GPIOs for panel- and
backlight-enable on BYT, when the VBT indicates the SoC should be used
for backlight control. It also ensures that the PWM0 pin is muxed to the
PWM controller in this case.
This fixes the LCD panel not lighting up on various devices when booted
with a HDMI monitor connected. This has been tested to fix this on the
following devices:
Peaq C1010
Point of View MOBII TAB-P800W
Point of View MOBII TAB-P1005W
Terra Pad 1061
Yours Y8W81
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-6-hdegoede@redhat.com
Move the Crystal Cove PMIC panel GPIO lookup-table from
drivers/mfd/intel_soc_pmic_core.c to the i915 driver.
The moved looked-up table is adding a GPIO lookup to the i915 PCI
device and the GPIO subsys allows only one lookup table per device,
The intel_soc_pmic_core.c code only adds lookup-table entries for the
PMIC panel GPIO (as it deals only with the PMIC), but we also need to be
able to access some GPIOs on the SoC itself, which requires entries for
these GPIOs in the lookup-table.
Since the lookup-table is attached to the i915 PCI device it really
should be part of the i915 driver, this will also allow us to extend
it with GPIOs from other sources when necessary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-5-hdegoede@redhat.com
When the LCD has not been turned on by the firmware/GOP, because e.g. the
device was booted with an external monitor connected over HDMI, we should
not turn on the panel-enable GPIO when we request it.
Turning on the panel-enable GPIO when we request it, means we turn it on
too early in the init-sequence, which causes some panels to not correctly
light up.
This commits adds a panel_is_on parameter to intel_dsi_vbt_gpio_init()
and makes intel_dsi_vbt_gpio_init() set the initial GPIO value accordingly.
This fixes the panel not lighting up on a Thundersoft TST168 tablet when
booted with an external monitor connected over HDMI.
Changes in v2:
- Call intel_dsi_get_hw_state() to check if the panel is on instead of
relying on the current_mode pointer
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-4-hdegoede@redhat.com
On some older devices (BYT, CHT) which may use v2 VBT MIPI-sequences,
we need to manually control the panel enable GPIO as v2 sequences do
not do this.
So far we have been carrying the code to do this on BYT/CHT devices
with a Crystal Cove PMIC in vlv_dsi.c, but as this really is a shortcoming
of the VBT MIPI-sequences, intel_dsi_vbt.c is a better place for this,
so move it there.
This is a preparation patch for adding panel-enable and backlight-enable
GPIO support for BYT devices where instead of the PMIC the SoC is used
for backlight control.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-3-hdegoede@redhat.com
