It is a preliminary work for supporting multiple EDP PSR and
DP PanelReplay. And it refactors singleton PSR to Multi Transcoder
supportable PSR.
And this moves and renames the i915_psr structure of drm_i915_private's to
intel_dp's intel_psr structure.
It also causes changes in PSR interrupt handling routine for supporting
multiple transcoders. But it does not change the scenario and timing of
enabling and disabling PSR. And it not support multiple pipes with
a single transcoder PSR case yet.
v2: Fix indentation and add comments
v3: Remove Blank line
v4: Rebased
v5: Rebased and Addressed Anshuman's review comment.
- Move calling of intel_psr_init() to intel_dp_init_connector()
v6: Address Anshuman's review comments
- Remove wrong comments and add comments for a limit of supporting of
a single pipe PSR
v7: Update intel_psr_compute_config() for supporting multiple transcoder
PSR on BDW+
v8: Address Anshuman's review comments
- Replace DRM_DEBUG_KMS with drm_dbg_kms() / DRM_WARN with drm_warn()
v9: Fix commit message
v10: Rebased
v11: Address Jose's review comment.
- Reorder calling order of intel_psr2_program_trans_man_trk_ctl().
- In order to reduce changes keep the old name for drm_i915_private.
- Change restrictions of multiple instances of PSR.
v12: Address Jose's review comment.
- Change the calling of intel_psr2_program_trans_man_trk_ctl() into
commit_pipe_config().
- Change a checking order of CAN_PSR() and connector_status to original
on i915_psr_sink_status_show().
- Drop unneeded intel_dp_update_pipe() function.
- In order to wait a specific encoder which belong to crtc_state on
intel_psr_wait_for_idle(), add checking of encoder.
- Add an whitespace to comments.
v13: Rebased and Address Jose's review comment.
- Add and use for_each_intel_psr_enabled_encoder() macro.
- In order to use correct frontbuffer_bit for each pipe,
fix intel_psr_invalidate() and intel_psr_flush().
- Remove redundant or unneeded codes.
- Update comments.
v14: Address Jose's review comment
- Add and use for_each_intel_encoder_can_psr() macro and
for_each_intel_encoder_mask_can_psr() macro.
- Add source_support member variable into intel_psr structure.
- Update CAN_PSR() macro that checks source_support.
- Move encoder's PSR availity check to psr_init() from
psr_compute_config().
- Remove redundant or unneeded codes.
v15: Remove wrong mutex lock/unlock of PSR from
intel_psr2_program_trans_man_trk_ctl()
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204134015.419036-1-gwan-gyeong.mun@intel.com
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com
This function sets the VRR property for connector based
on the platform support, EDID monitor range and DP sink
DPCD capability of outputing video without msa
timing information.
v8:
* Use HAS_VRR, remove drm_conn declaration (Jani N)
* Fix typos in Comment (Jani N)
v7:
* Move the helper to separate file (Manasi)
v6:
* Remove unset of prop
v5:
* Fix the vrr prop not being set in kernel (Manasi)
* Unset the prop on connector disconnect (Manasi)
v4:
* Rebase (Mansi)
v3:
* intel_dp_is_vrr_capable can be used for debugfs, make it
non static (Manasi)
v2:
* Just set this in intel_dp_get_modes instead of new hook (Jani)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-2-manasi.d.navare@intel.com
This reverts commit 0883ce8146. Originally
these quirks were added because of the issues with using the eDP
backlight interfaces on certain laptop panels, which made it impossible
to properly probe for DPCD backlight support without having a whitelist
for panels that we know have working VESA backlight control interfaces
over DPCD. As well, it should be noted it was impossible to use the
normal sink OUI for recognizing these panels as none of them actually
filled out their OUIs, hence needing to resort to checking EDIDs.
At the time we weren't really sure why certain panels had issues with
DPCD backlight controls, but we eventually figured out that there was a
second interface that these problematic laptop panels actually did work
with and advertise properly: Intel's proprietary backlight interface for
HDR panels. So far the testing we've done hasn't brought any panels to
light that advertise this interface and don't support it properly, which
means we finally have a real solution to this problem.
As a result, we now have no need for the force DPCD backlight quirk, and
furthermore this also removes the need for any kind of EDID quirk
checking in DRM. So, let's just revert it for now since we were the only
driver using this.
v3:
* Rebase
v2:
* Fix indenting error picked up by checkpatch in
intel_edp_init_connector()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114221709.2261452-6-lyude@redhat.com
drivers/gpu/drm/i915/display/intel_dp.c:6922 intel_dp_update_420() warn: should this be a bitwise op?
drivers/gpu/drm/i915/display/intel_dp.c:6922 intel_dp_update_420() warn: should this be a bitwise op?
drivers/gpu/drm/i915/display/intel_dp.c:6923 intel_dp_update_420() warn: should this be a bitwise op?
Inside drm_dp_downstream_rgb_to_ycbcr_conversion(), that parameter
'color_spc' is used as return port_cap[3] & color_spc, implying that it
is indeed a mask and not a boolean value.
Fixes: 522508b665 ("drm/i915/display: Let PCON convert from RGB to YCbCr if it can")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201223103917.14687-1-chris@chris-wilson.co.uk
The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().
intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.
This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com
Since we're about to start adding support for Intel's magic HDR
backlight interface over DPCD, we need to ensure we're properly
programming this field so that Intel specific sink services are exposed.
Otherwise, 0x300-0x3ff will just read zeroes.
We also take care not to reprogram the source OUI if it already matches
what we expect. This is just to be careful so that we don't accidentally
take the panel out of any backlight control modes we found it in.
v2:
* Add careful parameter to intel_edp_init_source_oui() to avoid
re-writing the source OUI if it's already been set during driver
initialization
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-2-lyude@redhat.com
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-13-ankit.k.nautiyal@intel.com
