The driver doesn't depend atm on the common mode timing generator
functionality (it would be used for some power saving feature and panel
timing synchronization), however DMC will corrupt the CMTG registers
across DC5 entry/exit sequences unless the CMTG clock gating is
disabled. This in turn can lead to at least the DPLL0/1 configuration
getting stuck at their last state, which means we can't reprogram them
to a new config.
Add the corresponding Bspec workaround to prevent the above.
v2: Fix checkpatch errors. (CI, Jose)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134400.101290-1-imre.deak@intel.com
ADL_P requires that we disable underrun recovery when downscaling (or
using the scaler for YUV420 pipe output), using DSC, or using PSR2.
Otherwise we should be able to enable the underrun recovery.
On DG2 we need to keep underrun recovery disabled at all times, but the
chicken bit in PIPE_CHICKEN has an inverted meaning (it's an enable bit
instead of disable).
v2:
- Reverse the condition (clear the disable bit when supported, set
disable bit when not supported).
Bspec: 50351
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727145056.2049720-1-matthew.d.roper@intel.com
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
Commit 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt
in intel_bios.c") moved the workaround for broken or missing VBT to
intel_bios.c. However is_port_valid() only protects the handling of
different skus of the same display version. Since in
intel_setup_outputs() we share the code path with version 9, this would
also create port F for SKL/KBL, which does not exist.
Missing VBT can be reproduced when starting a headless QEMU with no
opregion available.
Avoid the issue by splitting versions 9 and 10 in intel_setup_outputs(),
which also makes it more clear what code path it's taking for each
version.
v2: move generic display version after Geminilake since that one has
a different set of outputs
Fixes: 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt in intel_bios.c")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210722232922.3796835-1-lucas.demarchi@intel.com
(cherry picked from commit ec387b8ff8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Commit 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt
in intel_bios.c") moved the workaround for broken or missing VBT to
intel_bios.c. However is_port_valid() only protects the handling of
different skus of the same display version. Since in
intel_setup_outputs() we share the code path with version 9, this would
also create port F for SKL/KBL, which does not exist.
Missing VBT can be reproduced when starting a headless QEMU with no
opregion available.
Avoid the issue by splitting versions 9 and 10 in intel_setup_outputs(),
which also makes it more clear what code path it's taking for each
version.
v2: move generic display version after Geminilake since that one has
a different set of outputs
Fixes: 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt in intel_bios.c")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210722232922.3796835-1-lucas.demarchi@intel.com
A new step has been added to the DP modeset sequences for all platforms
with display version 12 and beyond: if enabling DP MST with FEC, we
need to set a chicken bit before enabling the transcoder. The chicken
bit should be disabled again before disabling the transcoder (which we
can do unconditionally since it shouldn't be set anyway in non-MST
cases).
Bspec: 49190, 54128, 55424
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723170618.1477415-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
Bring drm-intel-next closer to drm-next and drm-intel-gt-next for a more
feasible baseline for topic branches.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add a single point of truth for figuring out the primary/secondary crtc
for bigjoiner instead of duplicating the magic pipe +/- 1 in multiple
places.
Also fix the pipe validity checks to properly take non-contiguous pipes
into account. The current checks may theoretically overflow
i915->pipe_to_crtc_mapping[pipe], albeit with a warning, due to fused
off pipes, as INTEL_NUM_PIPES() returns the actual number of pipes on
the platform, and the check is for INTEL_NUM_PIPES() == pipe + 1.
Prefer primary/secondary terminology going forward.
v2:
- Improved abstractions for pipe validity etc.
Fixes: 8a029c113b ("drm/i915/dp: Modify VDSC helpers to configure DSC for Bigjoiner slave")
Fixes: d961eb20ad ("drm/i915/bigjoiner: atomic commit changes for uncompressed joiner")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.dl.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610090528.20511-1-jani.nikula@intel.com
(cherry picked from commit 17203224f0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add a single point of truth for figuring out the primary/secondary crtc
for bigjoiner instead of duplicating the magic pipe +/- 1 in multiple
places.
Also fix the pipe validity checks to properly take non-contiguous pipes
into account. The current checks may theoretically overflow
i915->pipe_to_crtc_mapping[pipe], albeit with a warning, due to fused
off pipes, as INTEL_NUM_PIPES() returns the actual number of pipes on
the platform, and the check is for INTEL_NUM_PIPES() == pipe + 1.
Prefer primary/secondary terminology going forward.
v2:
- Improved abstractions for pipe validity etc.
Fixes: 8a029c113b ("drm/i915/dp: Modify VDSC helpers to configure DSC for Bigjoiner slave")
Fixes: d961eb20ad ("drm/i915/bigjoiner: atomic commit changes for uncompressed joiner")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.dl.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610090528.20511-1-jani.nikula@intel.com
Commit 78b772e1a0 ("drm/i915/display: Fill PSR state during hardware
configuration read out") is not allowing fastsets to happen when PSR
states changes but PSR is a feature that can be enabled and disabled
during fastsets.
So here moving the PSR pipe conf checks to a block that is only
executed when checking if HW state matches with requested state, not
during the phase where it checks if fastset is possible or not.
There still a state mismatch not allowing fastsets between states
turning off or on PSR because of crtc_state->infoframes.enable
BIT(DP_SDP_VSC) but at least for now it will allow a fastset between
PSR1 <-> PSR2, that is a case heavilly used by CI due to pipe CRC not
work with PSR2, but the remaning issue will be fixed in a future patch.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 78b772e1a0 ("drm/i915/display: Fill PSR state during hardware configuration read out")
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-1-jose.souza@intel.com
UAPI Changes:
- Add reworked uAPI for DG1 behind CONFIG_BROKEN (Matt A, Abdiel)
Driver Changes:
- Fix for Gitlab issues #3293 and #3450:
Avoid kernel crash on older L-shape memory machines
- Add Wa_14010733141 (VDBox SFC reset) for Gen11+ (Aditya)
- Fix crash in auto_retire active retire callback due to
misalignment (Stephane)
- Fix overlay active retire callback alignment (Tvrtko)
- Eliminate need to align active retire callbacks (Matt A, Ville,
Daniel)
- Program FF_MODE2 tuning value for all Gen12 platforms (Caz)
- Add Wa_14011060649 for TGL,RKL,DG1 and ADLS (Swathi)
- Create stolen memory region from local memory on DG1 (CQ)
- Place PD in LMEM on dGFX (Matt A)
- Use WC when default state object is allocated in LMEM (Venkata)
- Determine the coherent map type based on object location (Venkata)
- Use lmem physical addresses for fb_mmap() on discrete (Mohammed)
- Bypass aperture on fbdev when LMEM is available (Anusha)
- Return error value when displayable BO not in LMEM for dGFX (Mohammed)
- Do release kernel context if breadcrumb measure fails (Janusz)
- Hide modparams for compiled-out features (Tvrtko)
- Apply Wa_22010271021 for all Gen11 platforms (Caz)
- Fix unlikely ref count race in arming the watchdog timer (Tvrtko)
- Check actual RC6 enable status in PMU (Tvrtko)
- Fix a double free in gen8_preallocate_top_level_pdp (Lv)
- Use trylock in shrinker for GGTT on BSW VT-d and BXT (Maarten)
- Remove erroneous i915_is_ggtt check for
I915_GEM_OBJECT_UNBIND_VM_TRYLOCK (Maarten)
- Convert uAPI headers to real kerneldoc (Matt A)
- Clean up kerneldoc warnings headers (Matt A, Maarten)
- Fail driver if LMEM training failed (Matt R)
- Avoid div-by-zero on Gen2 (Ville)
- Read C0DRB3/C1DRB3 as 16 bits again and add _BW suffix (Ville)
- Remove reference to struct drm_device.pdev (Thomas)
- Increase separation between GuC and execlists code (Chris, Matt B)
- Use might_alloc() (Bernard)
- Split DGFX_FEATURES from GEN12_FEATURES (Lucas)
- Deduplicate Wa_22010271021 programming on (Jose)
- Drop duplicate WaDisable4x2SubspanOptimization:hsw (Tvrtko)
- Selftest improvements (Chris, Hsin-Yi, Tvrtko)
- Shuffle around init_memory_region for stolen (Matt)
- Typo fixes (wengjianfeng)
[airlied: fix conflict with fixes in i915_active.c]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YLCbBR22BsQ/dpJB@jlahtine-mobl.ger.corp.intel.com
The kernel prefers enabling fbc over the initial fb, since this leads to
actual runtime power savings, so if the initial fb is deemed too big
using some heuristic, then we simply skip allocating stolen for it.
However if the kernel is not configured with fbcon then it should be
possible to relax this, since unlike with fbcon the display server
shouldn't preserve it when later replacing it, and so we should be able
to re-use the stolen memory for fbc and friends. This patch is reported
to fix some flicker seen during boot splash on some devices.
v2: s/FRAMEBUFFER_CONSOLE/CONFIG_FRAMEBUFFER_CONSOLE
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526124901.245689-1-matthew.auld@intel.com
Core Changes:
- drm: Rename DP_PSR_SELECTIVE_UPDATE to better mach eDP spec (Jose).
Driver Changes:
- Display plane clock rates fixes and improvements (Ville).
- Uninint DMC FW loader state during shutdown (Imre).
- Convert snprintf to sysfs_emit (Xuezhi).
- Fix invalid access to ACPI _DSM objects (Takashi).
- A big refactor around how i915 addresses the graphics
and display IP versions. (Matt, Lucas).
- Backlight fix (Lyude).
- Display watermark and DBUF fixes (Ville).
- HDCP fix (Anshuman).
- Improve cases where display is not available (Jose).
- Defeature PSR2 for RKL and ALD-S (Jose).
- VLV DSI panel power fixes and improvements (Hans).
- display-12 workaround (Jose).
- Fix modesetting (Imre).
- Drop redundant address-of op before lttpr_common_caps array (Imre).
- Fix compiler checks (Jose, Jason).
- GLK display fixes (Ville).
- Fix error code returns (Dan).
- eDP novel: back again to slow and wide link training everywhere (Kai-Heng).
- Abstract DMC FW path (Rodrigo).
- Preparation and changes for upcoming
XeLPD display IP (Jose, Matt, Ville, Juha-Pekka, Animesh).
- Fix comment typo in DSI code (zuoqilin).
- Simplify CCS and UV plane alignment handling (Imre).
- PSR Fixes on TGL (Gwan-gyeong, Jose).
- Add intel_dp_hdcp.h and rename init (Jani).
- Move crtc and dpll declarations around (Jani).
- Fix pre-skl DP AUX precharge length (Ville).
- Remove stray newlines from random files (Ville).
- crtc->index and intel_crtc+drm_crtc pointer clean-up (Ville).
- Add frontbuffer tracking tracepoints (Ville).
- ADL-S PCI ID updates (Anand).
- Use unique backlight device names (Jani).
- A few clean-ups on i915/audio (Jani).
- Use intel_framebuffer instead of drm one on intel_fb functions (Imre).
- Add the missing MC CCS/XYUV8888 format support on display >= 12 (Imre).
- Nuke display error state (Ville).
- ADL-P initial enablement patches
starting to land (Clint, Imre, Jose, Umesh, Vandita, Mika).
- Display clean-up around VBT and the strap bits (Lucas).
- Try YCbCr420 color when RGB fails (Werner).
- More PSR fixes and improvements (Jose).
- Other generic display code clean-up (Jose, Ville).
- Use correct downstream caps for check Src-Ctl mode for PCON (Ankit).
- Disable HiZ Raw Stall Optimization on broken gen7 (Simon).
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YKVioeu0JkUAlR7y@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
