Since this is a bridge, we don't start out with a respective DRM device.
Likewise this means we don't have a connector, which also means that we
should be following drm_dp_aux_register()'s documentation advice and not
call drm_dp_aux_register() until we have a matching connector. Instead,
call drm_dp_aux_init() in tc_probe() and wait until tc_bridge_attach() to
register our AUX channel. We also add tc_bridge_detach() to handle
unregistering the AUX adapter once the bridge has been disconnected.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-5-lyude@redhat.com
drm hotplug handling code (drm_client_dev_hotplug()) can wait on mutex,
thus delaying further lt9611uxc IRQ events processing. It was observed
occasionally during bootups, when drm_client_modeset_probe() was waiting
for EDID ready event, which was delayed because IRQ handler was stuck
trying to deliver hotplug event.
Move hotplug notifications from IRQ handler to separate work to be able
to process IRQ events without delays.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 0cbbd5b1a0 ("drm: bridge: add support for lontium LT9611UXC bridge")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210121233303.1221784-4-dmitry.baryshkov@linaro.org
The thc63lvd1024 driver requests a supply using regulator_get_optional()
but both the name of the supply and the usage pattern suggest that it is
being used for the main power for the device and is not at all optional
for the device for function, there is no handling at all for absent
supplies. Such regulators should use the vanilla regulator_get()
interface, it will ensure that even if a supply is not described in the
system integration one will be provided in software.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Required backmerge since we will be based on top of v5.11, and there
has been a request to backmerge already to upstream some features.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
Add DP support to display-connector driver. The driver will support HPD
via a GPIO and DP PWR.
DP PWR will be enabled at probe, which is not optimal, but I'm not sure
what would be a good place to enable and disable DP PWR. Perhaps
attach/detach, but I don't know if enabling HW is something that attach
is supposed to do.
In any case, I don't think there's much difference in power consumption
between the version in this patch and enabling the regulator later: if
the driver probes, supposedly it will attach very soon afterwards, and
we need to enable the DP PWR as soon as possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130112919.241054-3-tomi.valkeinen@ti.com
It has been observed that resetting force in the detect function can
result in the PHY being powered down in response to hot-plug detect
being asserted, even when the HDMI connector is forced on.
Enabling debug messages and adding a call to dump_stack() in
dw_hdmi_phy_power_off() shows the following in dmesg:
[ 160.637413] dwhdmi-rockchip ff940000.hdmi: EVENT=plugin
[ 160.637433] dwhdmi-rockchip ff940000.hdmi: PHY powered down in 0 iterations
Call trace:
dw_hdmi_phy_power_off
dw_hdmi_phy_disable
dw_hdmi_update_power
dw_hdmi_detect
dw_hdmi_connector_detect
drm_helper_probe_detect_ctx
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread_fn
irq_thread
kthread
ret_from_fork
Fixes: 381f05a7a8 ("drm: bridge/dw_hdmi: add connector mode forcing")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031081747.372599-1-net147@gmail.com
On the SII9022, the IOVCC and CVCC12 supplies must reach the correct
voltage before the reset sequence is initiated. On most boards, this
assumption is true at boot-up, so initialization succeeds.
However, when we try to initialize the chip with incorrect supply
voltages, it will not respond to I2C requests. sii902x_probe() fails
with -ENXIO.
To resolve this, look for the "iovcc" and "cvcc12" regulators, and
make sure they are enabled before starting the reset sequence. If
these supplies are not available in devicetree, then they will default
to dummy-regulator. In that case everything will work like before.
This was observed on a STM32MP157C-DK2 booting in u-boot falcon mode.
On this board, the supplies would be set by the second stage
bootloader, which does not run in falcon mode.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[Fix checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-2-mr.nuke.me@gmail.com
We should be setting the drm_dp_aux_msg::reply field if a NACK or a
SHORT reply happens. Update the error bit handling logic in
ti_sn_aux_transfer() to handle these cases and notify upper layers that
such errors have happened. This helps the retry logic understand that a
timeout has happened, or to shorten the read length if the panel isn't
able to handle the longest read possible.
Note: I don't have any hardware that exhibits these code paths so this
is written based on reading the datasheet for this bridge and inspecting
the code and how this is called.
Changes in v2:
- Move WRITE_STATUS_UPDATE check from case to assignment
Changes in v2:
- Handle WRITE_STATUS_UPDATE properly
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102181144.3469197-5-swboyd@chromium.org
On some panels hooked up to the ti-sn65dsi86 bridge chip we found that
link training was failing. Specifically, we'd see:
ti_sn65dsi86 2-002d: [drm:ti_sn_bridge_enable] *ERROR* Link training failed, link is off (-5)
The panel was hooked up to a logic analyzer and it was found that, as
part of link training, the bridge chip was writing a 0x1 to DPCD
address 00600h and the panel responded NACK. As can be seen in header
files, the write of 0x1 to DPCD address 0x600h means we were trying to
write the value DP_SET_POWER_D0 to the register DP_SET_POWER. The
panel vendor says that a NACK in this case is not unexpected and means
"not ready, try again".
In testing, we found that this panel would respond with a NACK in
about 1/25 times. Adding the retry logic worked fine and the most
number of tries needed was 3. Just to be safe, we'll add 10 tries
here and we'll add a little blurb to the logs if we ever need more
than 5.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002135920.1.I2adbc90b2db127763e2444bd5a4e5bf30e1db8e5@changeid
This patch restores DRM connector registration in the TC358764 bridge
driver and restores usage of the old drm_panel_* API, thus allows dynamic
panel registration. This fixes panel operation on Exynos5250-based
Arndale board.
This is equivalent to the revert of the following commits:
1644127f83 "drm/bridge: tc358764: add drm_panel_bridge support"
385ca38da2 "drm/bridge: tc358764: drop drm_connector_(un)register"
and removal of the calls to drm_panel_attach()/drm_panel_detach(), which
were no-ops and has been removed in meanwhile.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930114042.5806-1-m.szyprowski@samsung.com
drm-misc-next for 5.10:
UAPI Changes:
Cross-subsystem Changes:
- virtio: Merged a PR for patches that will affect drm/virtio
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
- atomic: Split out drm_atomic_helper_calc_timestamping_constants of
drm_atomic_helper_update_legacy_modeset_state
- ttm: More rework
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
- tree-wide: conversions to devm_drm_dev_alloc,
- ast: simplifications of the atomic modesetting code
- panfrost: multiple fixes
- vc4: multiple fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921152956.2gxnsdgxmwhvjyut@gilmour.lan
Add a new DRM bridge driver for Cadence MHDP8546 DPTX IP used in TI J721E
SoC. MHDP DPTX IP is the component that complies with VESA DisplayPort (DP)
and embedded Display Port (eDP) standards. It integrates uCPU running the
embedded Firmware (FW) interfaced over APB interface.
Basically, it takes a DPI stream as input and outputs it encoded in DP
format. Currently, it supports only SST mode.
Co-developed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Co-developed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_edid() callback can be triggered anytime by an ioctl, i.e
drm_mode_getconnector (ioctl)
-> drm_helper_probe_single_connector_modes
-> drm_bridge_connector_get_modes
-> ps8640_bridge_get_edid
Actually if the bridge pre_enable() function was not called before
get_edid(), the driver will not be able to get the EDID properly and
display will not work until a second get_edid() call is issued and if
pre_enable() is called before. The side effect of this, for example, is
that you see anything when `Frecon` starts, neither the splash screen,
until the graphical session manager starts.
To fix this we need to make sure that all we need is enabled before
reading the EDID. This means the following:
1. If get_edid() is called before having the device powered we need to
power on the device. In such case, the driver will power off again the
device.
2. If get_edid() is called after having the device powered, all should
just work. We added a powered flag in order to avoid recurrent calls
to ps8640_bridge_poweron() and unneeded delays.
3. This seems to be specific for this device, but we need to make sure
the panel is powered on before do a power on cycle on this device.
Otherwise the device fails to retrieve the EDID.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827085911.944899-2-enric.balletbo@collabora.com
