When testing with a panel that's apparently a little more persnickety
about the correct power sequence (specifically Samsung ATNA33XC20), we
found that the ti-sn65dsi86 was doing things just slightly wrong.
Looking closely at the ti-sn65dsi86's datasheet, the power off
sequence is supposed to be:
1. Clear VSTREAM_ENABLE bit
2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state.
3. Program the ML_TX_MODE to 0x0 (OFF)
4. Program the DP_NUM_LANES register to 0x0
5. Clear the DP_PLL_EN bit.
6. Deassert the EN pin.
7. Remove power from supply pins
Since we were doing the whole sequence in the "disable", I believe
that step #2 (stopping the DSI stream from the GPU) wasn't
happening. We also weren't setting DP_NUM_LANES to 0.
Let's fix this.
NOTE: things are a little asymmetric now. For instance, we turn the
PLL on in "enable" but now we're not turning it off until
"post_disable". It would seem to make sense to move the PLL turning on
to "pre_enable" to match. Unfortunately, I don't believe that's
allowed. It looks as if (in the non-refclk mode which probably nobody
is using) we have to wait until the MIPI clock is there before we can
enable the PLL. In any case, the way it is here won't really
hurt--it'll just leave the PLL on a little longer.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.2.If8a8ec3bf1855cf0dbb62c005a71d6698c99c125@changeid
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:
Before:
text data bss dec hex filename
24845 7440 64 32349 7e5d ./drivers/gpu/drm/bridge/tc358768.o
After:
text data bss dec hex filename
24749 7408 64 32221 7ddd ./drivers/gpu/drm/bridge/tc358768.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
The driver currently iterates over all connectors to get the bus format,
used to configure the LVDS output format. This causes several issues:
- If other connectors than the LVDS output are present, the format used
by the driver may end up belonging to an entirely different output.
- The code can crash if some connectors are not connected, as bus_format
may then be NULL.
- There's no guarantee that the bus format on the connector at the
output of the pipeline matches the output of the sn65dsi83, as there
may be other bridges in the pipeline.
Solve this by retrieving the format from the bridge state instead, which
provides the format corresponding to the output of the bridge.
The struct sn65dsi83 lvds_format_24bpp and lvds_format_jeida fields are
moved to local variables in sn65dsi83_atomic_enable() as they're now
used in that function only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621125518.13715-5-laurent.pinchart@ideasonboard.com
There were still a race condition between hpd work and suspend, since
the workqueue work can still be run after anx7625 had powered off in
suspend.
Since we never want hpd work to run while suspending, and there's no
harm to delay them to be run after resume, mark the workqueue as
WQ_FREEZABLE so all works won't run while suspending.
Fixes: 409776fa3c ("drm/bridge: anx7625: add suspend / resume hooks")
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210615032937.2328468-1-pihsun@chromium.org
This is really just a revert of commit 58074b08c0 ("drm/bridge:
ti-sn65dsi86: Read EDID blob over DDC"), resolving conflicts.
The old code failed to read the EDID properly in a very important
case: before the bridge's pre_enable() was called. The way things need
to work:
1. Read the EDID.
2. Based on the EDID, decide on video settings and pixel clock.
3. Enable the bridge w/ the desired settings.
The way things were working:
1. Try to read the EDID but fail; fall back to hardcoded values.
2. Based on hardcoded values, decide on video settings and pixel clock.
3. Enable the bridge w/ the desired settings.
4. Try again to read the EDID, it works now!
5. Realize that the hardcoded settings weren't quite right.
6. Disable / reenable the bridge w/ the right settings.
The reasons for the failures were twofold:
a) Since we never ran the bridge chip's pre-enable then we never set
the bit to ignore HPD. This meant the bridge chip didn't even _try_
to go out on the bus and communicate with the panel.
b) Even if we fixed things to ignore HPD, the EDID still wouldn't read
if the panel wasn't on.
Instead of reverting the code, we could fix it to set the HPD bit and
also power on the panel. However, it also works nicely to just let the
panel code read the EDID. Now that we've split the driver up we can
expose the DDC AUX channel bus to the panel node. The panel can take
charge of reading the EDID.
NOTE: in order for things to work, anyone that needs to read the EDID
will need to instantiate their panel using the new DP AUX bus (AKA by
listing their panel under the "aux-bus" node of the bridge chip in the
device tree).
In the future if we want to use the bridge chip to provide a full
external DP port (which won't have a panel) then we will have to
conditinally add EDID reading back in.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.9.I9330684c25f65bb318eff57f0616500f83eac3cc@changeid
On its own, this change looks a little strange and doesn't do too much
useful. To understand why we're doing this we need to look forward to
future patches where we're going to probe our panel using the new DP
AUX bus. See the patch ("drm/bridge: ti-sn65dsi86: Add support for the
DP AUX bus").
Let's think about the set of steps we'll want to happen when we have
the DP AUX bus:
1. We'll create the DP AUX bus.
2. We'll populate the devices on the DP AUX bus (AKA our panel).
3. For setting up the bridge-related functions of ti-sn65dsi86 we'll
need to get a reference to the panel.
If we do #1 - #3 in a single probe call things _mostly_ will work, but
it won't be massively robust. Let's explore.
First let's think of the easy case of no -EPROBE_DEFER. In that case
in step #2 when we populate the devices on the DP AUX bus it will
actually try probing the panel right away. Since the panel probe
doesn't defer then in step #3 we'll get a reference to the panel and
we're golden.
Second, let's think of the case when the panel returns
-EPROBE_DEFER. In that case step #2 won't synchronously create the
panel (it'll just add the device to the defer list to do it
later). Step #3 will fail to get the panel and the bridge sub-device
will return -EPROBE_DEFER. We'll depopulate the DP AUX bus. Later
we'll try the whole sequence again. Presumably the panel will
eventually stop returning -EPROBE_DEFER and we'll go back to the first
case where things were golden. So this case is OK too even if it's a
bit ugly that we have to keep creating / deleting the AUX bus over and
over.
So where is the problem? As I said, it's mostly about robustness. I
don't believe that step #2 (creating the sub-devices) is really
guaranteed to be synchronous. This is evidenced by the fact that it's
allowed to "succeed" by just sticking the device on the deferred
list. If anything about the process changes in Linux as a whole and
step #2 just kicks off the probe of the DP AUX endpoints (our panel)
in the background then we'd be in trouble because we might never get
the panel in step #3.
Adding an extra sub-device means we just don't need to worry about
it. We'll create the sub-device for the DP AUX bus and it won't go
away until the whole ti-sn65dsi86 driver goes away. If the bridge
sub-device defers (maybe because it can't find the panel) that won't
depopulate the DP AUX bus and so we don't need to worry about it.
NOTE: there's a little bit of a trick here. Though the AUX channel can
run without the MIPI-to-eDP bits of the code, the MIPI-to-eDP bits
can't run without the AUX channel. We could come up a complicated
signaling scheme (have the MIPI-to-eDP bits return EPROBE_DEFER for a
while or wait on some sort of completion), but it seems simple enough
to just not even bother creating the bridge device until the AUX
channel probes. That's what we'll do.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.7.If89144992cb9d900f8c91a8d1817dbe00f543720@changeid
Fix the following sparse warnings generated by "make C=1":
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: expected unsigned short [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: got restricted __le16 [usertype]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608142211.82333-1-marex@denx.de
Originally when using pm_runtime_put, there's a chance that the runtime
suspend hook will be run after the following anx7625_bridge_mode_set
call, resulting in the display_timing_valid field to be cleared, and the
following power on fail.
Change all pm_runtime_put to pm_runtime_put_sync, so all power off
operations are guaranteed to be done after the call returns.
Fixes: 60487584a7 ("drm/bridge: anx7625: refactor power control to use runtime PM framework")
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520064508.3121211-1-pihsun@chromium.org
The ti_sn_aux_transfer() function returns ssize_t (signed long). It's
supposed to return negative error codes or the number of bytes
transferred. The "ret" variable is int and the "len" variable is
unsigned int.
The problem is that with a ternary like this, the negative int is first
type promoted to unsigned int to match "len" at this point it is a high
positive value. Then when it is type promoted to ssize_t (s64) it
remains a high positive value instead of sign extending and becoming a
negative again.
Fix this by removing the ternary.
Fixes: b137406d96 ("drm/bridge: ti-sn65dsi86: If refclk, DP AUX can happen w/out pre-enable")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/YKOGogHasIyvF8nj@mwanda
The driver originally use an atomic_t for keep track of the power
status, which makes the driver more complicated than needed, and has
some race condition as it's possible to have the power on and power off
sequence going at the same time.
This patch remove the usage of the atomic_t power_status, and use the
kernel runtime power management framework instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517063553.554955-1-pihsun@chromium.org
