When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d1 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It will connect to the mipi dsi host and find the corresponding
mipi dsi host node, but the node registered by the mipi dsi host
has not been loaded yet. of_find_mipi_dsi_host_by_node() returns -EINVAL
which causes the calling driver to fail.
If the anx7625 driver is loaded afterwards the driver requesting
the mipi dsi host will not notice this.
Better approach is to return -EPROBE_DEFER in such case.
Then when the anx7625 driver appears the driver requesting
the mipi dsi host will be probed again.
Signed-off-by: owen <qwt9588@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117100949.9542-1-qwt9588@gamil.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Move DisplayPort functions into a separate module to reduce the size
of the KMS helpers. Select DRM_DP_HELPER for all users of the code. To
avoid naming conflicts, rename drm_dp_helper.c to drm_dp.c
This change can help to reduce the size of the kernel binary. Some
numbers from a x86-64 test build:
Before:
drm_kms_helper.ko: 447480 bytes
After:
drm_dp_helper.ko: 216632 bytes
drm_kms_helper.ko: 239424 bytes
For early-boot graphics, generic DRM drivers, such as simpledrm,
require DRM KMS helpers to be built into the kernel. Generic helper
functions for DisplayPort take up a significant portion of DRM KMS
helper library. These functions are not used by generic drivers and
can be loaded as a module.
v3:
* fix include statement in DRM selftests
v2:
* move DP helper code into dp/ (Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-4-tzimmermann@suse.de
When DRM_CHIPONE_ICN6211 is selected, and DRM_KMS_HELPER is not selected,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for DRM_PANEL_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && DRM_KMS_HELPER [=n]
Selected by [y]:
- DRM_CHIPONE_ICN6211 [=y] && HAS_IOMEM [=y] && DRM [=y] && DRM_BRIDGE [=y] && OF [=y]
This is because DRM_CHIPONE_ICN6211 selects DRM_PANEL_BRIDGE
without depending on or selecting DRM_KMS_HELPER,
despite DRM_PANEL_BRIDGE depending on DRM_KMS_HELPER.
This unmet dependency bug was detected by Kismet,
a static analysis tool for Kconfig.
Fixes: ce517f1894 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge")
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117052146.75811-1-julianbraha@gmail.com
Entering suspend while the display attached to this bridge is still on
makes the resume sequence to resume the bridge first, display last:
when this happens, we get a timeout while resuming the bridge, as its
MCU will get stuck due to the display being unpowered.
On the other hand, on mt8173-elm, closing the lid makes the display to
get powered off first, bridge last, so at resume time the sequence is
swapped (compared to the first example) and everything just works
as expected.
Add a stateless device link to the DRM device that this bridge belongs
to, ensuring a correct resume sequence and solving the unability to
correctly resume bridge operation in the first mentioned example.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105090802.73564-1-angelogioacchino.delregno@collabora.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
When we added the support for the AUX channel in commit 13afcdd727
("drm/bridge: parade-ps8640: Add support for AUX channel") we forgot
to set "drm_dev" to avoid the warning splat at the beginning of
drm_dp_aux_register(). Since everything was working I guess I never
noticed the splat when testing against mainline. In any case, it's
easy to fix. This is basically just like commit 6cba3fe433 ("drm/dp:
Add backpointer to drm_device in drm_dp_aux") but just for the
parade-ps8640.
Fixes: 13afcdd727 ("drm/bridge: parade-ps8640: Add support for AUX channel")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206162907.1.I1f5d1eba741e4663050ec1b8e39a753f6e42e38b@changeid
Since this bridge is tied to the connector, it acts like a passthrough,
so concerning the output & input bus formats, either pass the bus formats from the
previous bridge or return fallback data like done in the bridge function:
drm_atomic_bridge_chain_select_bus_fmts() & select_bus_fmt_recursive.
This permits avoiding skipping the negociation if the remaining bridge chain has
all the bits in place.
Without this bus fmt negociation breaks on drm/meson HDMI pipeline when attaching
dw-hdmi with DRM_BRIDGE_ATTACH_NO_CONNECTOR, because the last bridge of the
display-connector doesn't implement buf fmt callbacks and MEDIA_BUS_FMT_FIXED
is used leading to select an unsupported default bus format from dw-hdmi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020123947.2585572-2-narmstrong@baylibre.com
The current ELD handling takes the internal connector ELD buffer and
shares it to the I2S and AHB sub-driver.
But with DRM_BRIDGE_ATTACH_NO_CONNECTOR, the connector is created
elsewhere (or not), and an eventual connector is known only
if the bridge chain up to a connector is enabled.
The current dw-hdmi code gets the current connector from
atomic_enable() so use the already stored connector pointer and
replace the buffer pointer with a callback returning the current
connector ELD buffer.
Since a connector is not always available, either pass an empty
ELD to the alsa HDMI driver or don't call snd_pcm_hw_constraint_eld()
in AHB driver.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029135947.3022875-1-narmstrong@baylibre.com
Conventionally, panel is listed under the root of the device tree.
When userland asks for display mode, ps8640 bridge is responsible
for returning EDID when ps8640_bridge_get_edid() is called.
Now enable a new option of listing panel under "aux-bus" of ps8640
bridge node in the device tree. In this case, panel driver can retrieve
EDID by triggering AUX transactions, without ps8640_bridge_get_edid()
calls at all.
To prevent the "old" and "new" options from interfering with each
other's logic flow, disable DRM_BRIDGE_OP_EDID when the new option
is taken.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028105754.v5.2.I09899dea340f11feab97d719cb4b62bef3179e4b@changeid
Fit ps8640 driver into runtime power management framework:
First, break _poweron() to 3 parts: (1) turn on power and wait for
ps8640's internal MCU to finish init (2) check panel HPD (which is
proxied by GPIO9) (3) the other configs. As runtime_resume() can be
called before panel is powered, we only add (1) to _resume() and leave
(2)(3) to _pre_enable(). We also add (2) to _aux_transfer() as we want
to ensure panel HPD is asserted before we start AUX CH transactions.
Second, the original driver has a mysterious delay of 50 ms between (2)
and (3). Since Parade's support can't explain what the delay is for,
and we don't see removing the delay break any boards at hand, remove
the delay to fit into this driver change.
In addition, rename "powered" to "pre_enabled" and don't check for it
in the pm_runtime calls. The pm_runtime calls are already refcounted
so there's no reason to check there. The other user of "powered",
_get_edid(), only cares if pre_enable() has already been called.
Lastly, change some existing DRM_...() logging to dev_...() along the
way, since DRM_...() seem to be deprecated in [1].
[1] https://patchwork.freedesktop.org/patch/454760/
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: fixed whitespace warning reported by dim tool]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028105754.v5.1.I828f5db745535fb7e36e8ffdd62d546f6d08b6d1@changeid
Prior to commit 6c836d965b ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:
"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""
However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.
It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:
According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."
Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.
Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
