EIC controller have unfixed numbers of banks on different Spreadtrum SoCs,
and each bank has its own base address, the loop of getting there base
address in driver should break if the resource gotten via
platform_get_resource() is NULL already. The later ones would be all NULL
even if the loop continues.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201209055106.840100-1-zhang.lyra@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we already have a few virtual GPIO drivers, and more to come,
this category deserves its own submenu.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When trying to export an nonexisting gpio ID, the kernel prints out a
big warning w/ stacktrace, sounding like a huge problem. In fact it's
a pretty normal situation, like file or device not found.
So, just print a more relaxed warning instead.
changes v2: drop defining pr_fmt()
Signed-off-by: Enrico Weigelt <info@metux.net>
Link: https://lore.kernel.org/r/20201202133754.32045-1-info@metux.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using CLOCK_REALTIME as the source for event timestamps is crucial for
some specific applications, particularly those requiring timetamps
relative to a PTP clock, so provide an option to switch the event
timestamp source from the default CLOCK_MONOTONIC to CLOCK_REALTIME.
Note that CLOCK_REALTIME was the default source clock for GPIO until
Linux 5.7 when it was changed to CLOCK_MONOTONIC due to issues with the
shifting of the realtime clock.
Providing this option maintains the CLOCK_MONOTONIC as the default,
while also providing a path forward for those dependent on the pre-5.7
behaviour.
Suggested-by: Jack Winch <sunt.un.morcov@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20201014231158.34117-2-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver that supports the GPIO block found in
MStar/SigmaStar ARMv7 SoCs.
The controller seems to have enough register for 128 lines
but where they are wired up differs between chips and
no currently known chip uses anywhere near 128 lines so there
needs to be some per-chip data to collect together what lines
actually have physical pins attached and map the right names to them.
The core peripherals seem to use the same lines on the
currently known chips but the lines used for the sensor
interface, lcd controller etc pins seem to be totally
different between the infinity and mercury chips
The code tries to collect all of the re-usable names,
offsets etc together so that it's easy to build the extra
per-chip data for other chips in the future.
So far this only supports the MSC313 and MSC313E chips.
Support for the SSC8336N (mercury5) is trivial to add once
all of the lines have been mapped out.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201129110803.2461700-4-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If users select sysfs support they get the character device
as well so that end-users cannot complain that they
"only have sysfs on my system". They should have the
character device at all times.
If someone is in so dire need of stripping out the
character device while still enabling the sysfs ABI they
can very well patch the kernel.
Also only show this obsolete option to expert users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201110142724.14760-1-linus.walleij@linaro.org
Commit 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
changed most readl/writel registers access calls to the regmap API in
preparation for Armada 7K/8K support. PWM duration registers were left using
readl/writel, as the driver does not support PWM for Armada 7K/8K.
Switch PWM duration registers to regmap as first step in adding Armada 7K/8K
PWM functionality support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to putting operation will result in a
reference leak here.
A new function pm_runtime_resume_and_get is introduced in
[0] to keep usage counter balanced. So We fix the reference
leak by replacing it with new funtion.
[0] dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Fixes: c2df3de0d0 ("gpio: zynq: properly support runtime PM for GPIO used as interrupts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
A similar check was added in gpiochip_generic_request, but not in free.
This has caused an imbalance count of request vs. free calls to the
pinctrl driver. This patch is targeted to fix that issue.
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Signed-off-by: Edmond Chung <edmondchung@google.com>
Signed-off-by: Andrew Chant <achant@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
Fixes:27a49ed17e224(gpio: arizona: Add support for GPIOs that)
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip may have dependencies from pinmux and so got deferred. Now it
will print error message every time -EPROBE_DEFER is returned which is
unnecessary:
"gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517"
Hence, do suppress error message for -EPROBE_DEFER case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by explicitly adding a fallthrough pseudo-keyword to indicate
that the code is intended to fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip_add_data() may return -EPROBE_DEFER which is not handled
properly by TI GPIO driver and causes unnecessary boot log messages.
Hence, add proper deferred probe handling with new dev_err_probe() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no matching spi_get_drvdata() call in the driver, so there is no
need to do spi_set_drvdata(). This looks like it probably was copied from a
driver that used both spi_set_drvdata() & spi_get_drvdata().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In dwapb_get_reset(), if devm_reset_control_get_optional_shared() fails,
an error message is printed even if the failure is the benign
EPROBE_DEFER error due to the reset controller not yet being
initialized. Use dev_err_probe() to handle
devm_reset_control_get_optional_shared() errors to avoid unnecessarilly
printing an error message for the deferred probe error.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We can simplify the error path in probe() and drop remove() entirely if
we provide a devm action for freeing the device ID.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can simplify the code in gpio-exar by using regmap. This allows us to
drop the mutex (regmap provides its own locking) and we can also reuse
regmap's bit operations instead of implementing our own update function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Provide and use helpers for calculating the register address and bit
offset instead of hand coding it in every function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's more elegant to use a helper local variable to store the address
of the underlying struct device than to dereference pdev everywhere. It
also has the benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to specify any ranges when allocating IDs so we can switch
to ida_alloc() and ida_free() instead of the ida_simple_ counterparts.
ida_simple_get(ida, 0, 0, gfp) is equivalent to
ida_alloc_range(ida, 0, UINT_MAX, gfp) which is equivalent to
ida_alloc(ida, gfp). Note: IDR will never actually allocate an ID
larger than INT_MAX.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can get hwirq number of the gpio by its irq_data->hwirq so that we don't
need to add more macros for different platforms. This patch is tested in
SiFive Unleashed board and SiFive Unmatched board.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
GpioIo() resources don't contain an initial value for the output pin.
Therefore instead of deducting its value solely based on bias field
we should deduce that value from the polarity and the bias fields.
Typical scenario is, when pin is defined in the table and its polarity,
specified in _DSD or via platform code, is defined as active low,
in the following call chain:
-> acpi_populate_gpio_lookup()
-> acpi_gpio_to_gpiod_flags()
it will return GPIOD_OUT_HIGH if bias is set no matter if polarity
is GPIO_ACTIVE_LOW, so it will return the current level instead of
the logical level.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vasile-Laurentiu Stanimir <vasile-laurentiu.stanimir@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases the GpioInt() resource is coming with bias settings
which may affect system functioning. Respect bias settings for
GpioInt() resource by calling acpi_gpio_update_gpiod_*flags() API
in acpi_dev_gpio_irq_get().
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
