Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
Recent Allwinner SoCs support >4 GiB of DRAM, so those variants of the
DMA engine support >32 bit physical addresses. This is accomplished by
placing the high bits in the "para" word in the DMA descriptor.
DMA descriptors themselves can be located at >32 bit addresses by
putting the high bits in the LSBs of the descriptor address register,
taking advantage of the required DMA descriptor alignment. However,
support for this is not really necessary, so we can avoid the
complication by allocating them from the DMA_32 zone.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220424172759.33383-4-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At any time, a DMA transfer can be suspended to be restarted later before
the end of the DMA transfer.
In order to restart from the point where the transfer was stopped,
DMA_SxNDTR has to be read after disabling the channel by clearing the EN
bit in DMA_SxCR register, to know the number of data items already
collected.
Peripheral and/or memory addresses have to be updated in order to adjust
the address pointers.
SxNDTR register has to be updated with the remaining number of data items
to be transferred (the value read when the channel was disabled).
Then the channel can be re-enabled to resume the transfer from the point
it was suspended.
If the channel was configured in circular or double-buffer mode, the
circular or double-buffer mode must be disabled before re-enabling the
channel to be able to reconfigure SxNDTR register and re-activate circular
or double-buffer mode on next Transfer Complete interrupt where channel
will be disabled by HW. This is due to the fact that on resume, re-writing
SxNDTR register value updates internal HW auto-reload data counter, and
then it truncates all next transfers after a pause/resume sequence.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
stm32_dma_handle_chan_done() is called on Transfer Complete interrupt.
As DMA_SxSCR register is read in interrupt handler, pass the value as
parameter of stm32_dma_handle_chan_done(). Also return directly if
chan->desc is null to remove one ident level.
Then, stm32_dma_configure_next_sg() is doing something only if
Double-Buffer Mode (DBM) is enabled, so, check it is enabled prior calling
stm32_dma_configure_next_sg(), to remove one ident level in
stm32_dma_configure_next_sg().
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
chan->next_sg is used to know which transfer will start after the ongoing
one. It is incremented for each new transfer, either on transfer start for
non-cyclic transfers, or on transfer complete interrupt for cyclic
transfers.
For cyclic transfer, when the last item is reached, chan->next_sg must be
reinitialized to the first item.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the two DMA controllers managed by the DMAMUX can be used by the
coprocessor. It is defined in the device tree with dma-masters.
When the two DMA controllers are used by the main CPU,
dma-masters = <&dma1, &dma2>; is specified in the device tree.
When one of the controllers is used by coprocessor (so not managed by
Linux), dma-masters = <&dma1>; is specified in the device tree.
In this case, Linux driver must not reset the DMAMUX, because it could have
been configured by the coprocessor to use the second DMA controller.
count is the number of DMA controllers defined in dma-masters property.
Reset only if resets property is found and valid in device tree, and if
the two DMA controllers are under Linux control.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220504161724.123180-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drivers/dma/tegra186-gpc-dma.c: In function ‘tegra_dma_probe’:
drivers/dma/tegra186-gpc-dma.c:1364:24: error: ‘struct iommu_fwspec’ has no member named ‘ids’
stream_id = iommu_spec->ids[0] & 0xffff;
^~
Make TEGRA186_GPC_DMA depends on IOMMU_API to fix this.
Fixes: ee17028009 ("dmaengine: tegra: Add tegra gpcdma driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220505093236.15076-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZN1 DMA IP is based on a DW core, with eg. an additional
dmamux register located in the system control area which can take up to
32 requests (16 per DMA controller). Each DMA channel can be wired to
two different peripherals.
We need two additional information from the 'dmas' property: the channel
(bit in the dmamux register) that must be accessed and the value of the
mux for this channel.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220427095653.91804-6-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In zynqmp_dma_alloc/free_chan_resources functions there is a
potential overflow in the below expressions.
dma_alloc_coherent(chan->dev, (2 * chan->desc_size *
ZYNQMP_DMA_NUM_DESCS),
&chan->desc_pool_p, GFP_KERNEL);
dma_free_coherent(chan->dev,(2 * ZYNQMP_DMA_DESC_SIZE(chan) *
ZYNQMP_DMA_NUM_DESCS),
chan->desc_pool_v, chan->desc_pool_p);
The arguments desc_size and ZYNQMP_DMA_NUM_DESCS were 32 bit. Though
this overflow condition is not observed but it is a potential problem
in the case of 32-bit multiplication. Hence fix it by changing the
desc_size data type to size_t.
In addition to coverity fix it also reuse ZYNQMP_DMA_DESC_SIZE macro in
dma_alloc_coherent API argument.
Addresses-Coverity: Event overflow_before_widen.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1652166762-18317-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use platform_irq_get() instead platform_get_resource() for IRQ resource
to fix the probe failure. platform_get_resource() fails to fetch the IRQ
resource as it might not be ready at that time.
platform_irq_get() is also the recommended way to get interrupt as it
directly gives the IRQ number and no conversion from resource is
required.
Fixes: ee17028009 ("dmaengine: tegra: Add tegra gpcdma driver")
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220505091440.12981-1-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The legacy interface for omap-dma is only used on OMAP1, and the
same is true for the non-DT case. Make both of these conditional on
CONFIG_ARCH_OMAP1 being set to simplify the dependency.
The non-OMAP stub functions in include/linux/omap-dma.h are note needed
any more either now, because they are only called on OMAP1.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
LKP bot reports a new warning:
Warning:
drivers/dma/ptdma/ptdma-dmaengine.c:262:1: warning: no previous prototype for 'pt_tx_status' [-Wmissing-prototypes]
pt_tx_status() should be static, so declare as such.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d965068259 ("dmaengine: PTDMA: support polled mode")
Link: https://lore.kernel.org/r/20220421052407.745637-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
