The 'unevaluatedProperties' schema checks is not fully working and doesn't
catch some cases where there's a $ref to another schema. A fix is pending,
but results in new warnings in examples. Fix the warnings by removing
spurious properties or adding missing properties to the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220526014149.2872762-1-robh@kernel.org
Pull ARM DT updates from Arnd Bergmann:
"There are 40 branches this time, adding a lot of new hardware support,
and cleanups. Krzysztof Kozlowski continues his treewide cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the
RZ/G2L general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for
designing custom SoCs, the support for now is for the Fixed Virtual
Platform emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly for
32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based IOT
board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch, a
Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568"
* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
ARM: dts: turris-omnia: Add atsha204a node
arm64: dts: mt8192: Follow binding order for SCP registers
arm64: dts: mediatek: add mtk-snfi for mt7622
arm64: dts: mediatek: mt8195-demo: enable uart1
...
Pull devicetree updates from Rob Herring:
"Bindings:
- Convert smsc,lan91c111, qcom,spi-qup, qcom,msm-uartdm,
qcom,i2c-qup, qcom,gsbi, i2c-mt65xx, TI wkup_m3_ipc (and new
props), qcom,smp2p, TI timer, Mediatek gnss, Mediatek topckgen,
Mediatek apmixedsys, Mediatek infracfg, fsl,ls-extirq,
fsl,layerscape-dcfg, QCom PMIC SPMI, rda,8810pl-timer, Xilinx
zynqmp_ipi, uniphier-pcie, and Ilitek touchscreen controllers
- Convert various Arm Ltd peripheral IP bindings to schemas
- New bindings for Menlo board CPLD, DH electronics board CPLD,
Qualcomm Geni based QUP I2C, Renesas RZ/G2UL OSTM, Broafcom BCM4751
GNSS, MT6360 PMIC, ASIX USB Ethernet controllers, and
Microchip/SMSC LAN95xx USB Ethernet controllers
- Add vendor prefix for Enclustra
- Add various compatible string additions
- Various example fixes and cleanups
- Remove unused hisilicon,hi6220-reset binding
- Treewide fix properties missing type definition
- Drop some empty and unreferenced .txt bindings
- Documentation improvements for writing schemas
DT driver core:
- Drop static IRQ resources for DT platform devices as IRQ setup is
dynamic and drivers have all been converted to use
platform_get_irq() and friends
- Rework memory allocations and frees for overlays
- Continue overlay notifier callbacks on successful calls and add
unittests
- Handle 'interrupts-extended' in early DT IRQ setup
- Fix of_property_read_string() errors to match documentation
- Ignore disabled nodes in FDT API calls"
* tag 'devicetree-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (86 commits)
of/irq: fix typo in comment
dt-bindings: Fix properties without any type
Revert "dt-bindings: mailbox: qcom-ipcc: add missing properties into example"
dt-bindings: input: touchscreen: ilitek_ts_i2c: Absorb ili2xxx bindings
dt-bindings: timer: samsung,exynos4210-mct: define strict clock order
dt-bindings: timer: samsung,exynos4210-mct: drop unneeded minItems
dt-bindings: timer: cdns,ttc: drop unneeded minItems
dt-bindings: mailbox: zynqmp_ipi: convert to yaml
dt-bindings: usb: ci-hdrc-usb2: fix node node for ethernet controller
dt-bindings: net: add schema for Microchip/SMSC LAN95xx USB Ethernet controllers
dt-bindings: net: add schema for ASIX USB Ethernet controllers
of/fdt: Ignore disabled memory nodes
dt-bindings: arm: fix typos in compatible
dt-bindings: mfd: Add bindings child nodes for the Mediatek MT6360
dt-bindings: display: convert Arm Komeda to DT schema
dt-bindings: display: convert Arm Mali-DP to DT schema
dt-bindings: display: convert Arm HDLCD to DT schema
dt-bindings: display: convert PL110/PL111 to DT schema
dt-bindings: arm: convert vexpress-config to DT schema
dt-bindings: arm: convert vexpress-sysregs to DT schema
...
Now that the schema tools can extract type information for all
properties (in order to decode dtb files), finding properties missing
any type definition is fairly trivial though not yet automated.
Fix the various property schemas which are missing a type. Most of these
tend to be device specific properties which don't have a vendor prefix.
A vendor prefix is how we normally ensure a type is defined.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for everything in .../bindings/display/
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220519211411.2200720-1-robh@kernel.org
ath.git patches for v5.19. Major changes:
ath11k
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
WCN6750 is the WLAN chip on Qualcomm Snapdragon SoC SC7280;
Though being a PCIe based solution, it is not attached to
the APSS processor (Application Processor SubSystem), it is
instead attached to another tiny processor called WPSS Q6
processor (Wireless Processor SubSystem) on the SC7280 MSM,
where the WLAN firmware runs, and it is the WLAN firmware
running on the Q6 processor which enumerates WCN6750, as a
result APPS processor would never know such a device being
present in the system and would not detect the WCN6750
hardware unless and otherwise WCN6750 is registered as a
platform device. This is the reason behind adding WCN6750
WLAN node in the device tree.
Add WCN6750 wireless driver support, its based on ath11k driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-2-quic_mpubbise@quicinc.com
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
Add the capability to disable/enable radar/CAC detection running on
a dedicated offchannel chain available on some hw.
Offchannel radar/CAC detection allows to avoid CAC downtime switching
on a different channel during CAC detection on the selected radar
channel.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Pull devicetree updates from Rob Herring:
"Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom
Command DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl,
Tegra I2C and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt
controllers, STB GPIO, STB waketimer, STB reset, iProc MDIO mux,
iProc PCIe, Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON,
SYSTEMPORT, AMAC, Northstar 2 PCIe PHY, GENET, moca PHY, GISB
arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in
preparation to move to validating DTB files directly (instead of
intermediate YAML representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes"
* tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (114 commits)
dt-bindings: net: mdio: Drop resets/reset-names child properties
dt-bindings: clock: samsung: convert S5Pv210 to dtschema
dt-bindings: clock: samsung: convert Exynos5410 to dtschema
dt-bindings: clock: samsung: convert Exynos5260 to dtschema
dt-bindings: clock: samsung: extend Exynos7 bindings with UFS
dt-bindings: clock: samsung: convert Exynos7 to dtschema
dt-bindings: clock: samsung: convert Exynos5433 to dtschema
dt-bindings: i2c: maxim,max96712: Add bindings for Maxim Integrated MAX96712
dt-bindings: iio: adi,ltc2983: Fix 64-bit property sizes
dt-bindings: power: maxim,max17040: Fix incorrect type for 'maxim,rcomp'
dt-bindings: interrupt-controller: arm,gic-v3: Fix 'interrupts' cell size in example
dt-bindings: iio/magnetometer: yamaha,yas530: Fix invalid 'interrupts' in example
dt-bindings: clock: imx5: Drop clock consumer node from example
dt-bindings: Drop required 'interrupt-parent'
dt-bindings: net: ti,dp83869: Drop value on boolean 'ti,max-output-impedance'
dt-bindings: net: wireless: mt76: Fix 8-bit property sizes
dt-bindings: PCI: snps,dw-pcie-ep: Drop conflicting 'max-functions' schema
dt-bindings: i2c: st,stm32-i2c: Make each example a separate entry
dt-bindings: net: stm32-dwmac: Make each example a separate entry
dt-bindings: net: Cleanup MDIO node schemas
...
The '/bits/ 8' notation applies the next <> list of values. Another <> list
is encoded as 32-bits by default. IOW, each <> list needs to be preceeded
with '/bits/ 8'.
While the dts format allows this, as a rule we don't mix sizes for DT
properties since all size information is lost in the dtb file.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220107030419.2380198-1-robh@kernel.org
Pull devicetree updates from Rob Herring:
- Convert /reserved-memory bindings to schemas
- Convert a bunch of NFC bindings to schemas
- Convert bindings to schema: Xilinx USB, Freescale DDR controller, Arm
CCI-400, UBlox Neo-6M, 1-Wire GPIO, MSI controller, ASpeed LPC, OMAP
and Inside-Secure HWRNG, register-bit-led, OV5640, Silead GSL1680,
Elan ekth3000, Marvell bluetooth, TI wlcore, TI bluetooth, ESP
ESP8089, tlm,trusted-foundations, Microchip cap11xx, Ralink SoCs and
boards, and TI sysc
- New binding schemas for: msi-ranges, Aspeed UART routing controller,
palmbus, Xylon LogiCVC display controller, Mediatek's MT7621 SDRAM
memory controller, and Apple M1 PCIe host
- Run schema checks for %.dtb targets
- Improve build time when using DT_SCHEMA_FILES
- Improve error message when dtschema is not found
- Various doc reference fixes in MAINTAINERS
- Convert architectures to common CPU h/w ID parsing function
of_get_cpu_hwid().
- Allow for empty NUMA node IDs which may be hotplugged
- Cleanup of __fdt_scan_reserved_mem()
- Constify device_node parameters
- Update dtc to upstream v1.6.1-19-g0a3a9d3449c8. Adds new checks
'node_name_vs_property_name' and 'interrupt_map'.
- Enable dtc 'unit_address_format' warning by default
- Fix unittest EXPECT text for gpio hog errors
* tag 'devicetree-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (97 commits)
dt-bindings: net: ti,bluetooth: Document default max-speed
dt-bindings: pci: rcar-pci-ep: Document r8a7795
dt-bindings: net: qcom,ipa: IPA does support up to two iommus
of/fdt: Remove of_scan_flat_dt() usage for __fdt_scan_reserved_mem()
of: unittest: document intentional interrupt-map provider build warning
of: unittest: fix EXPECT text for gpio hog errors
of/unittest: Disable new dtc node_name_vs_property_name and interrupt_map warnings
scripts/dtc: Update to upstream version v1.6.1-19-g0a3a9d3449c8
dt-bindings: arm: firmware: tlm,trusted-foundations: Convert txt bindings to yaml
dt-bindings: display: tilcd: Fix endpoint addressing in example
dt-bindings: input: microchip,cap11xx: Convert txt bindings to yaml
dt-bindings: ufs: exynos-ufs: add exynosautov9 compatible
dt-bindings: ufs: exynos-ufs: add io-coherency property
dt-bindings: mips: convert Ralink SoCs and boards to schema
dt-bindings: display: xilinx: Fix example with psgtr
dt-bindings: net: nfc: nxp,pn544: Convert txt bindings to yaml
dt-bindings: Add a help message when dtschema tools are missing
dt-bindings: bus: ti-sysc: Update to use yaml binding
dt-bindings: sram: Allow numbers in sram region node name
dt-bindings: display: Document the Xylon LogiCVC display controller
...
mt76 patches for 5.16
* various bugfixes
* endian fixes
* mt7921 aspm support
* cleanup
* mt7921 testmode support
* rate handling fixes
* tx status fixes/improvements
* mt7921 power management improvements
* mt7915 LED support
* DBDC fixes
* mt7921 6GHz support
* support for eeprom data in DT
* mt7915 TWT support
* mt7915 txbf + MU-MIMO improvements
# gpg: Signature made Wed 20 Oct 2021 12:24:46 PM EEST
# gpg: using DSA key D77D141D02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
EEPROM data for mt76 can be embedded into device-tree as an array.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This replaces the existing .txt binding file. Furthermore, this
also helps with validating DTS files.
Introduced binding changes:
1. added inherited mac-address nvmem property
2. added inherited ieee80211-freq-limit property
3. added new calibration nvmem property
4. added second example (taken from the Netgear WNDR3700v2)
Reason: Setting qca,no-eeprom; takes presedence over
nvmem-cells. I think a different example is needed,
because the driver can only reads from one calibration
source per device.
5. (re-added) chip list (based on data from ath9k's pci.c)
Added binding .yaml to MAINTAINERS.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210924223509.52525-1-chunkeey@gmail.com
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Introduce power-limits node in mt76 binding in order to specify
per-rate power limit values for each 802.11n/802.11ac rate
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add optional brcm,ccode-map property to support translation from ISO3166
country code to brcmfmac firmware country code and revision.
The country revision is needed because the RF parameters that provide
regulatory compliance are tweaked per platform/customer. So depending
on the RF path tight to the chip, certain country revision needs to be
specified. As such they could be seen as device specific calibration
data which is a good fit into device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20210415104728.8471-2-shawn.guo@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert mt76 dts bindings from .txt to .yaml
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Convert generic ieee80211 dts bindings from .txt to .yaml
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
MT7622 is a SoC that includes a 2.4 GHz 4x4 802.11n WMAC. Its
feature set is comparable to a MT7615 chip, but limited to 2.4 GHz.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce big-endian property to specify mtd radio partition endianness
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is now only useful for SPI interface.
Power control of SDIO mode is done through mmc core.
Suggested by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin
which will be used by ath10k driver to identify coex support
of a hardware and notify wifi firmware the gpio pin number.
This pin number information is needed for the hardware QCA4019.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for v5.6. Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
ath11k is a driver for Qualcomm IEEE 802.11ax devices. Add a
bindings document for the driver, first documenting IPQ8074 which is the
only device ath11k currently supports.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
