gpio: add tps65218 gpio
Driver for the GPIO block found in ti's tps65218 pmics. The device has two GPIOs and one GPO pin which can be configured as follows: GPIO1: -general-purpose, open-drain output controlled by GPO1 user bit and/or sequencer -DDR3 reset input signal from SOC. Signal is either latched or passed-trough to GPO2 pin. See below for details. GPO2: -general-purpose output controlled by GPO2 user bit -DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD. See below for details. -Output buffer can be configured as open-drain or push-pull. GPIO3: -general-purpose, open-drain output controlled by GPO3 user bit and/or sequencer -reset input-signal for DCDC1 and DCDC2. The input configurations are not meant to be used by the user so the driver only offers GPOs. v2: Added request routine that evaluates the fw config flags and removed module owner v3: Added .direction_input() routine, and took care of all Linus Walleij suggestions (clamp to bool, use proper include) Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
parent
b866526d0c
commit
c366c76a2c
@ -889,6 +889,13 @@ config GPIO_TIMBERDALE
|
|||||||
---help---
|
---help---
|
||||||
Add support for the GPIO IP in the timberdale FPGA.
|
Add support for the GPIO IP in the timberdale FPGA.
|
||||||
|
|
||||||
|
config GPIO_TPS65218
|
||||||
|
tristate "TPS65218 GPIO"
|
||||||
|
depends on MFD_TPS65218
|
||||||
|
help
|
||||||
|
Select this option to enable GPIO driver for the TPS65218
|
||||||
|
chip family.
|
||||||
|
|
||||||
config GPIO_TPS6586X
|
config GPIO_TPS6586X
|
||||||
bool "TPS6586X GPIO"
|
bool "TPS6586X GPIO"
|
||||||
depends on MFD_TPS6586X
|
depends on MFD_TPS6586X
|
||||||
|
@ -98,6 +98,7 @@ obj-$(CONFIG_ARCH_TEGRA) += gpio-tegra.o
|
|||||||
obj-$(CONFIG_GPIO_TIMBERDALE) += gpio-timberdale.o
|
obj-$(CONFIG_GPIO_TIMBERDALE) += gpio-timberdale.o
|
||||||
obj-$(CONFIG_GPIO_PALMAS) += gpio-palmas.o
|
obj-$(CONFIG_GPIO_PALMAS) += gpio-palmas.o
|
||||||
obj-$(CONFIG_GPIO_TPIC2810) += gpio-tpic2810.o
|
obj-$(CONFIG_GPIO_TPIC2810) += gpio-tpic2810.o
|
||||||
|
obj-$(CONFIG_GPIO_TPS65218) += gpio-tps65218.o
|
||||||
obj-$(CONFIG_GPIO_TPS6586X) += gpio-tps6586x.o
|
obj-$(CONFIG_GPIO_TPS6586X) += gpio-tps6586x.o
|
||||||
obj-$(CONFIG_GPIO_TPS65910) += gpio-tps65910.o
|
obj-$(CONFIG_GPIO_TPS65910) += gpio-tps65910.o
|
||||||
obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o
|
obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o
|
||||||
|
223
drivers/gpio/gpio-tps65218.c
Normal file
223
drivers/gpio/gpio-tps65218.c
Normal file
@ -0,0 +1,223 @@
|
|||||||
|
/*
|
||||||
|
* Copyright 2015 Verifone Int.
|
||||||
|
*
|
||||||
|
* Author: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
|
||||||
|
*
|
||||||
|
* This program is free software; you can redistribute it and/or modify i t
|
||||||
|
* under the terms of the GNU General Public License as published by th e
|
||||||
|
* Free Software Foundation; either version 2 of the License, or (at you r
|
||||||
|
* option) any later version.
|
||||||
|
*
|
||||||
|
* This driver is based on the gpio-tps65912 implementation.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include <linux/kernel.h>
|
||||||
|
#include <linux/module.h>
|
||||||
|
#include <linux/errno.h>
|
||||||
|
#include <linux/gpio/driver.h>
|
||||||
|
#include <linux/platform_device.h>
|
||||||
|
#include <linux/mfd/tps65218.h>
|
||||||
|
#include "gpiolib.h"
|
||||||
|
|
||||||
|
struct tps65218_gpio {
|
||||||
|
struct tps65218 *tps65218;
|
||||||
|
struct gpio_chip gpio_chip;
|
||||||
|
};
|
||||||
|
|
||||||
|
static int tps65218_gpio_get(struct gpio_chip *gc, unsigned offset)
|
||||||
|
{
|
||||||
|
struct tps65218_gpio *tps65218_gpio = gpiochip_get_data(gc);
|
||||||
|
struct tps65218 *tps65218 = tps65218_gpio->tps65218;
|
||||||
|
unsigned int val;
|
||||||
|
int ret;
|
||||||
|
|
||||||
|
ret = tps65218_reg_read(tps65218, TPS65218_REG_ENABLE2, &val);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
return !!(val & (TPS65218_ENABLE2_GPIO1 << offset));
|
||||||
|
}
|
||||||
|
|
||||||
|
static void tps65218_gpio_set(struct gpio_chip *gc, unsigned offset,
|
||||||
|
int value)
|
||||||
|
{
|
||||||
|
struct tps65218_gpio *tps65218_gpio = gpiochip_get_data(gc);
|
||||||
|
struct tps65218 *tps65218 = tps65218_gpio->tps65218;
|
||||||
|
|
||||||
|
if (value)
|
||||||
|
tps65218_set_bits(tps65218, TPS65218_REG_ENABLE2,
|
||||||
|
TPS65218_ENABLE2_GPIO1 << offset,
|
||||||
|
TPS65218_ENABLE2_GPIO1 << offset,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
else
|
||||||
|
tps65218_clear_bits(tps65218, TPS65218_REG_ENABLE2,
|
||||||
|
TPS65218_ENABLE2_GPIO1 << offset,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
}
|
||||||
|
|
||||||
|
static int tps65218_gpio_output(struct gpio_chip *gc, unsigned offset,
|
||||||
|
int value)
|
||||||
|
{
|
||||||
|
/* Only drives GPOs */
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int tps65218_gpio_input(struct gpio_chip *gc, unsigned offset)
|
||||||
|
{
|
||||||
|
return -EPERM;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int tps65218_gpio_request(struct gpio_chip *gc, unsigned offset)
|
||||||
|
{
|
||||||
|
struct tps65218_gpio *tps65218_gpio = gpiochip_get_data(gc);
|
||||||
|
struct tps65218 *tps65218 = tps65218_gpio->tps65218;
|
||||||
|
unsigned long flags = gc->desc[offset].flags;
|
||||||
|
int ret;
|
||||||
|
|
||||||
|
if (flags & FLAG_OPEN_SOURCE) {
|
||||||
|
dev_err(gc->parent, "can't work as open source\n");
|
||||||
|
return -EINVAL;
|
||||||
|
}
|
||||||
|
|
||||||
|
switch (offset) {
|
||||||
|
case 0:
|
||||||
|
if (!(flags & FLAG_OPEN_DRAIN)) {
|
||||||
|
dev_err(gc->parent, "GPO1 works only as open drain\n");
|
||||||
|
return -EINVAL;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Disable sequencer for GPO1 */
|
||||||
|
ret = tps65218_clear_bits(tps65218, TPS65218_REG_SEQ7,
|
||||||
|
TPS65218_SEQ7_GPO1_SEQ_MASK,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
/* Setup GPO1 */
|
||||||
|
ret = tps65218_clear_bits(tps65218, TPS65218_REG_CONFIG1,
|
||||||
|
TPS65218_CONFIG1_IO1_SEL,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
break;
|
||||||
|
case 1:
|
||||||
|
/* GP02 is push-pull by default, can be set as open drain. */
|
||||||
|
if (flags & FLAG_OPEN_DRAIN) {
|
||||||
|
ret = tps65218_clear_bits(tps65218,
|
||||||
|
TPS65218_REG_CONFIG1,
|
||||||
|
TPS65218_CONFIG1_GPO2_BUF,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Setup GPO2 */
|
||||||
|
ret = tps65218_clear_bits(tps65218, TPS65218_REG_CONFIG1,
|
||||||
|
TPS65218_CONFIG1_IO1_SEL,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
break;
|
||||||
|
|
||||||
|
case 2:
|
||||||
|
if (!(flags & FLAG_OPEN_DRAIN)) {
|
||||||
|
dev_err(gc->parent, "GPO3 works only as open drain\n");
|
||||||
|
return -EINVAL;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Disable sequencer for GPO3 */
|
||||||
|
ret = tps65218_clear_bits(tps65218, TPS65218_REG_SEQ7,
|
||||||
|
TPS65218_SEQ7_GPO3_SEQ_MASK,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
/* Setup GPO3 */
|
||||||
|
ret = tps65218_clear_bits(tps65218, TPS65218_REG_CONFIG2,
|
||||||
|
TPS65218_CONFIG2_DC12_RST,
|
||||||
|
TPS65218_PROTECT_L1);
|
||||||
|
if (ret)
|
||||||
|
return ret;
|
||||||
|
|
||||||
|
break;
|
||||||
|
default:
|
||||||
|
return -EINVAL;
|
||||||
|
}
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
|
||||||
|
static struct gpio_chip template_chip = {
|
||||||
|
.label = "gpio-tps65218",
|
||||||
|
.owner = THIS_MODULE,
|
||||||
|
.request = tps65218_gpio_request,
|
||||||
|
.direction_output = tps65218_gpio_output,
|
||||||
|
.direction_input = tps65218_gpio_input,
|
||||||
|
.get = tps65218_gpio_get,
|
||||||
|
.set = tps65218_gpio_set,
|
||||||
|
.can_sleep = true,
|
||||||
|
.ngpio = 3,
|
||||||
|
.base = -1,
|
||||||
|
};
|
||||||
|
|
||||||
|
static int tps65218_gpio_probe(struct platform_device *pdev)
|
||||||
|
{
|
||||||
|
struct tps65218 *tps65218 = dev_get_drvdata(pdev->dev.parent);
|
||||||
|
struct tps65218_gpio *tps65218_gpio;
|
||||||
|
int ret;
|
||||||
|
|
||||||
|
tps65218_gpio = devm_kzalloc(&pdev->dev, sizeof(*tps65218_gpio),
|
||||||
|
GFP_KERNEL);
|
||||||
|
if (!tps65218_gpio)
|
||||||
|
return -ENOMEM;
|
||||||
|
|
||||||
|
tps65218_gpio->tps65218 = tps65218;
|
||||||
|
tps65218_gpio->gpio_chip = template_chip;
|
||||||
|
tps65218_gpio->gpio_chip.parent = &pdev->dev;
|
||||||
|
#ifdef CONFIG_OF_GPIO
|
||||||
|
tps65218_gpio->gpio_chip.of_node = pdev->dev.of_node;
|
||||||
|
#endif
|
||||||
|
|
||||||
|
ret = gpiochip_add_data(&tps65218_gpio->gpio_chip, tps65218_gpio);
|
||||||
|
if (ret < 0) {
|
||||||
|
dev_err(&pdev->dev, "Failed to register gpiochip, %d\n", ret);
|
||||||
|
return ret;
|
||||||
|
}
|
||||||
|
|
||||||
|
platform_set_drvdata(pdev, tps65218_gpio);
|
||||||
|
|
||||||
|
return ret;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int tps65218_gpio_remove(struct platform_device *pdev)
|
||||||
|
{
|
||||||
|
struct tps65218_gpio *tps65218_gpio = platform_get_drvdata(pdev);
|
||||||
|
|
||||||
|
gpiochip_remove(&tps65218_gpio->gpio_chip);
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
|
||||||
|
static const struct of_device_id tps65218_dt_match[] = {
|
||||||
|
{ .compatible = "ti,tps65218-gpio" },
|
||||||
|
{ }
|
||||||
|
};
|
||||||
|
MODULE_DEVICE_TABLE(of, tps65218_dt_match);
|
||||||
|
|
||||||
|
static struct platform_driver tps65218_gpio_driver = {
|
||||||
|
.driver = {
|
||||||
|
.name = "tps65218-gpio",
|
||||||
|
.of_match_table = of_match_ptr(tps65218_dt_match)
|
||||||
|
},
|
||||||
|
.probe = tps65218_gpio_probe,
|
||||||
|
.remove = tps65218_gpio_remove,
|
||||||
|
};
|
||||||
|
|
||||||
|
module_platform_driver(tps65218_gpio_driver);
|
||||||
|
|
||||||
|
MODULE_AUTHOR("Nicolas Saenz Julienne <nicolassaenzj@gmail.com>");
|
||||||
|
MODULE_DESCRIPTION("GPO interface for TPS65218 PMICs");
|
||||||
|
MODULE_LICENSE("GPL v2");
|
||||||
|
MODULE_ALIAS("platform:tps65218-gpio");
|
Loading…
Reference in New Issue
Block a user