CRIS: drop unused Kconfig symbols

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
This commit is contained in:
Paul Bolle 2013-09-10 17:38:07 +02:00 committed by Jesper Nilsson
parent b172b370a0
commit be8cb7f42a
4 changed files with 0 additions and 467 deletions

View File

@ -172,12 +172,6 @@ config ETRAX_FLASH_BUSWIDTH
help
Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.
config ETRAX_NANDFLASH_BUSWIDTH
int "Buswidth of NAND flash in bytes"
default "1"
help
Width in bytes of the NAND flash (1 or 2).
config ETRAX_FLASH1_SIZE
int "FLASH1 size (dec, in MB. 0 = Unknown)"
default "0"
@ -543,26 +537,6 @@ config ETRAX_SERIAL_PORT3_DMA5_IN
depends on ETRAX_ARCH_V10
bool "DMA 5"
config ETRAX_SERIAL_PORT3_DMA9_IN
bool "Ser3 uses DMA9 for input"
depends on ETRAXFS
help
Enables the DMA9 input channel for ser3 (ttyS3).
If you do not enable DMA, an interrupt for each character will be
used when receiving data.
Normally you want to use DMA, unless you use the DMA channel for
something else.
config ETRAX_SERIAL_PORT3_DMA3_IN
bool "Ser3 uses DMA3 for input"
depends on CRIS_MACH_ARTPEC3
help
Enables the DMA3 input channel for ser3 (ttyS3).
If you do not enable DMA, an interrupt for each character will be
used when receiving data.
Normally you want to use DMA, unless you use the DMA channel for
something else.
endchoice
choice
@ -580,26 +554,6 @@ config ETRAX_SERIAL_PORT3_DMA4_OUT
depends on ETRAX_ARCH_V10
bool "DMA 4"
config ETRAX_SERIAL_PORT3_DMA8_OUT
bool "Ser3 uses DMA8 for output"
depends on ETRAXFS
help
Enables the DMA8 output channel for ser3 (ttyS3).
If you do not enable DMA, an interrupt for each character will be
used when transmitting data.
Normally you want to use DMA, unless you use the DMA channel for
something else.
config ETRAX_SERIAL_PORT3_DMA2_OUT
bool "Ser3 uses DMA2 for output"
depends on CRIS_MACH_ARTPEC3
help
Enables the DMA2 output channel for ser3 (ttyS3).
If you do not enable DMA, an interrupt for each character will be
used when transmitting data.
Normally you want to use DMA, unless you use the DMA channel for
something else.
endchoice
endmenu

View File

@ -417,16 +417,6 @@ config ETRAX_USB_HOST
for CTRL and BULK traffic only, INTR traffic may work as well
however (depending on the requirements of timeliness).
config ETRAX_USB_HOST_PORT1
bool "USB port 1 enabled"
depends on ETRAX_USB_HOST
default n
config ETRAX_USB_HOST_PORT2
bool "USB port 2 enabled"
depends on ETRAX_USB_HOST
default n
config ETRAX_PTABLE_SECTOR
int "Byte-offset of partition table sector"
depends on ETRAX_AXISFLASHMAP
@ -527,19 +517,6 @@ config ETRAX_GPIO
Remember that you need to setup the port directions appropriately in
the General configuration.
config ETRAX_PA_BUTTON_BITMASK
hex "PA-buttons bitmask"
depends on ETRAX_GPIO
default "02"
help
This is a bitmask with information about what bits on PA that
are used for buttons.
Most products has a so called TEST button on PA1, if that's true
use 02 here.
Use 00 if there are no buttons on PA.
If the bitmask is <> 00 a button driver will be included in the gpio
driver. ETRAX general I/O support must be enabled.
config ETRAX_PA_CHANGEABLE_DIR
hex "PA user changeable dir mask"
depends on ETRAX_GPIO

View File

@ -19,64 +19,6 @@ config ETRAX_NO_PHY
switch. This option should normally be disabled. If enabled,
speed and duplex will be locked to 100 Mbit and full duplex.
config ETRAX_ETHERNET_IFACE0
depends on ETRAX_ETHERNET
bool "Enable network interface 0"
config ETRAX_ETHERNET_IFACE1
depends on (ETRAX_ETHERNET && ETRAXFS)
bool "Enable network interface 1 (uses DMA6 and DMA7)"
config ETRAX_ETHERNET_GBIT
depends on (ETRAX_ETHERNET && CRIS_MACH_ARTPEC3)
bool "Enable gigabit Ethernet support"
choice
prompt "Eth0 led group"
depends on ETRAX_ETHERNET_IFACE0
default ETRAX_ETH0_USE_LEDGRP0
config ETRAX_ETH0_USE_LEDGRP0
bool "Use LED grp 0"
depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
help
Use LED grp 0 for eth0
config ETRAX_ETH0_USE_LEDGRP1
bool "Use LED grp 1"
depends on ETRAX_NBR_LED_GRP_TWO
help
Use LED grp 1 for eth0
config ETRAX_ETH0_USE_LEDGRPNULL
bool "Use no LEDs for eth0"
help
Use no LEDs for eth0
endchoice
choice
prompt "Eth1 led group"
depends on ETRAX_ETHERNET_IFACE1
default ETRAX_ETH1_USE_LEDGRP1
config ETRAX_ETH1_USE_LEDGRP0
bool "Use LED grp 0"
depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
help
Use LED grp 0 for eth1
config ETRAX_ETH1_USE_LEDGRP1
bool "Use LED grp 1"
depends on ETRAX_NBR_LED_GRP_TWO
help
Use LED grp 1 for eth1
config ETRAX_ETH1_USE_LEDGRPNULL
bool "Use no LEDs for eth1"
help
Use no LEDs for eth1
endchoice
config ETRAXFS_SERIAL
bool "Serial-port support"
depends on ETRAX_ARCH_V32
@ -108,261 +50,24 @@ config ETRAX_SERIAL_PORT0
if you do not need DMA to something else.
ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.
choice
prompt "Ser0 default port type "
depends on ETRAX_SERIAL_PORT0
default ETRAX_SERIAL_PORT0_TYPE_232
help
Type of serial port.
config ETRAX_SERIAL_PORT0_TYPE_232
bool "Ser0 is a RS-232 port"
help
Configure serial port 0 to be a RS-232 port.
config ETRAX_SERIAL_PORT0_TYPE_485HD
bool "Ser0 is a half duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 0 to be a half duplex (two wires) RS-485 port.
config ETRAX_SERIAL_PORT0_TYPE_485FD
bool "Ser0 is a full duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 0 to be a full duplex (four wires) RS-485 port.
endchoice
config ETRAX_SER0_DTR_BIT
string "Ser 0 DTR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT0
config ETRAX_SER0_RI_BIT
string "Ser 0 RI bit (empty = not used)"
depends on ETRAX_SERIAL_PORT0
config ETRAX_SER0_DSR_BIT
string "Ser 0 DSR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT0
config ETRAX_SER0_CD_BIT
string "Ser 0 CD bit (empty = not used)"
depends on ETRAX_SERIAL_PORT0
config ETRAX_SERIAL_PORT1
bool "Serial port 1 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser1 (ttyS1).
choice
prompt "Ser1 default port type"
depends on ETRAX_SERIAL_PORT1
default ETRAX_SERIAL_PORT1_TYPE_232
help
Type of serial port.
config ETRAX_SERIAL_PORT1_TYPE_232
bool "Ser1 is a RS-232 port"
help
Configure serial port 1 to be a RS-232 port.
config ETRAX_SERIAL_PORT1_TYPE_485HD
bool "Ser1 is a half duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 1 to be a half duplex (two wires) RS-485 port.
config ETRAX_SERIAL_PORT1_TYPE_485FD
bool "Ser1 is a full duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 1 to be a full duplex (four wires) RS-485 port.
endchoice
config ETRAX_SER1_DTR_BIT
string "Ser 1 DTR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT1
config ETRAX_SER1_RI_BIT
string "Ser 1 RI bit (empty = not used)"
depends on ETRAX_SERIAL_PORT1
config ETRAX_SER1_DSR_BIT
string "Ser 1 DSR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT1
config ETRAX_SER1_CD_BIT
string "Ser 1 CD bit (empty = not used)"
depends on ETRAX_SERIAL_PORT1
config ETRAX_SERIAL_PORT2
bool "Serial port 2 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser2 (ttyS2).
choice
prompt "Ser2 default port type"
depends on ETRAX_SERIAL_PORT2
default ETRAX_SERIAL_PORT2_TYPE_232
help
What DMA channel to use for ser2
config ETRAX_SERIAL_PORT2_TYPE_232
bool "Ser2 is a RS-232 port"
help
Configure serial port 2 to be a RS-232 port.
config ETRAX_SERIAL_PORT2_TYPE_485HD
bool "Ser2 is a half duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 2 to be a half duplex (two wires) RS-485 port.
config ETRAX_SERIAL_PORT2_TYPE_485FD
bool "Ser2 is a full duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 2 to be a full duplex (four wires) RS-485 port.
endchoice
config ETRAX_SER2_DTR_BIT
string "Ser 2 DTR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT2
config ETRAX_SER2_RI_BIT
string "Ser 2 RI bit (empty = not used)"
depends on ETRAX_SERIAL_PORT2
config ETRAX_SER2_DSR_BIT
string "Ser 2 DSR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT2
config ETRAX_SER2_CD_BIT
string "Ser 2 CD bit (empty = not used)"
depends on ETRAX_SERIAL_PORT2
config ETRAX_SERIAL_PORT3
bool "Serial port 3 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser3 (ttyS3).
choice
prompt "Ser3 default port type"
depends on ETRAX_SERIAL_PORT3
default ETRAX_SERIAL_PORT3_TYPE_232
help
What DMA channel to use for ser3.
config ETRAX_SERIAL_PORT3_TYPE_232
bool "Ser3 is a RS-232 port"
help
Configure serial port 3 to be a RS-232 port.
config ETRAX_SERIAL_PORT3_TYPE_485HD
bool "Ser3 is a half duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 3 to be a half duplex (two wires) RS-485 port.
config ETRAX_SERIAL_PORT3_TYPE_485FD
bool "Ser3 is a full duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 3 to be a full duplex (four wires) RS-485 port.
endchoice
config ETRAX_SER3_DTR_BIT
string "Ser 3 DTR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT3
config ETRAX_SER3_RI_BIT
string "Ser 3 RI bit (empty = not used)"
depends on ETRAX_SERIAL_PORT3
config ETRAX_SER3_DSR_BIT
string "Ser 3 DSR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT3
config ETRAX_SER3_CD_BIT
string "Ser 3 CD bit (empty = not used)"
depends on ETRAX_SERIAL_PORT3
config ETRAX_SERIAL_PORT4
bool "Serial port 4 enabled"
depends on ETRAXFS_SERIAL && CRIS_MACH_ARTPEC3
help
Enables the ETRAX FS serial driver for ser4 (ttyS4).
choice
prompt "Ser4 default port type"
depends on ETRAX_SERIAL_PORT4
default ETRAX_SERIAL_PORT4_TYPE_232
help
What DMA channel to use for ser4.
config ETRAX_SERIAL_PORT4_TYPE_232
bool "Ser4 is a RS-232 port"
help
Configure serial port 4 to be a RS-232 port.
config ETRAX_SERIAL_PORT4_TYPE_485HD
bool "Ser4 is a half duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 4 to be a half duplex (two wires) RS-485 port.
config ETRAX_SERIAL_PORT4_TYPE_485FD
bool "Ser4 is a full duplex RS-485 port"
depends on ETRAX_RS485
help
Configure serial port 4 to be a full duplex (four wires) RS-485 port.
endchoice
choice
prompt "Ser4 DMA in channel "
depends on ETRAX_SERIAL_PORT4
default ETRAX_SERIAL_PORT4_NO_DMA_IN
help
What DMA channel to use for ser4.
config ETRAX_SERIAL_PORT4_NO_DMA_IN
bool "Ser4 uses no DMA for input"
help
Do not use DMA for ser4 input.
config ETRAX_SERIAL_PORT4_DMA9_IN
bool "Ser4 uses DMA9 for input"
depends on ETRAX_SERIAL_PORT4
help
Enables the DMA9 input channel for ser4 (ttyS4).
If you do not enable DMA, an interrupt for each character will be
used when receiving data.
Normally you want to use DMA, unless you use the DMA channel for
something else.
endchoice
config ETRAX_SER4_DTR_BIT
string "Ser 4 DTR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT4
config ETRAX_SER4_RI_BIT
string "Ser 4 RI bit (empty = not used)"
depends on ETRAX_SERIAL_PORT4
config ETRAX_SER4_DSR_BIT
string "Ser 4 DSR bit (empty = not used)"
depends on ETRAX_SERIAL_PORT4
config ETRAX_SER4_CD_BIT
string "Ser 4 CD bit (empty = not used)"
depends on ETRAX_SERIAL_PORT4
config ETRAX_SYNCHRONOUS_SERIAL
bool "Synchronous serial-port support"
depends on ETRAX_ARCH_V32
@ -703,32 +408,6 @@ config ETRAX_SPI_SSER0
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
config ETRAX_SPI_SSER0_DMA
bool "DMA for SPI on sser0 enabled"
depends on ETRAX_SPI_SSER0
depends on !ETRAX_SERIAL_PORT1_DMA4_OUT && !ETRAX_SERIAL_PORT1_DMA5_IN
default y
help
Say Y if using DMA (dma4/dma5) for SPI on synchronous serial port 0.
config ETRAX_SPI_MMC_CD_SSER0_PIN
string "MMC/SD card detect pin for SPI on sser0"
depends on ETRAX_SPI_SSER0 && MMC_SPI
default "pd11"
help
The pin to use for SD/MMC card detect. This pin should be pulled up
and grounded when a card is present. If defined as " " (space), no
pin is selected. A card must then always be inserted for proper
action.
config ETRAX_SPI_MMC_WP_SSER0_PIN
string "MMC/SD card write-protect pin for SPI on sser0"
depends on ETRAX_SPI_SSER0 && MMC_SPI
default "pd10"
help
The pin to use for the SD/MMC write-protect signal for a memory
card. If defined as " " (space), the card is considered writable.
config ETRAX_SPI_SSER1
tristate "SPI using synchronous serial port 1 (sser1)"
depends on ETRAX_SPI_MMC
@ -742,32 +421,6 @@ config ETRAX_SPI_SSER1
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
config ETRAX_SPI_SSER1_DMA
bool "DMA for SPI on sser1 enabled"
depends on ETRAX_SPI_SSER1 && !ETRAX_ETHERNET_IFACE1
depends on !ETRAX_SERIAL_PORT0_DMA6_OUT && !ETRAX_SERIAL_PORT0_DMA7_IN
default y
help
Say Y if using DMA (dma6/dma7) for SPI on synchronous serial port 1.
config ETRAX_SPI_MMC_CD_SSER1_PIN
string "MMC/SD card detect pin for SPI on sser1"
depends on ETRAX_SPI_SSER1 && MMC_SPI
default "pd12"
help
The pin to use for SD/MMC card detect. This pin should be pulled up
and grounded when a card is present. If defined as " " (space), no
pin is selected. A card must then always be inserted for proper
action.
config ETRAX_SPI_MMC_WP_SSER1_PIN
string "MMC/SD card write-protect pin for SPI on sser1"
depends on ETRAX_SPI_SSER1 && MMC_SPI
default "pd9"
help
The pin to use for the SD/MMC write-protect signal for a memory
card. If defined as " " (space), the card is considered writable.
config ETRAX_SPI_GPIO
tristate "Bitbanged SPI using gpio pins"
depends on ETRAX_SPI_MMC
@ -782,51 +435,4 @@ config ETRAX_SPI_GPIO
Say m to build it as a module, which will be called spi_crisv32_gpio.
(You need to select MMC separately.)
# The default match that of sser0, only because that's how it was tested.
config ETRAX_SPI_CS_PIN
string "SPI chip select pin"
depends on ETRAX_SPI_GPIO
default "pc3"
help
The pin to use for SPI chip select.
config ETRAX_SPI_CLK_PIN
string "SPI clock pin"
depends on ETRAX_SPI_GPIO
default "pc1"
help
The pin to use for the SPI clock.
config ETRAX_SPI_DATAIN_PIN
string "SPI MISO (data in) pin"
depends on ETRAX_SPI_GPIO
default "pc16"
help
The pin to use for SPI data in from the device.
config ETRAX_SPI_DATAOUT_PIN
string "SPI MOSI (data out) pin"
depends on ETRAX_SPI_GPIO
default "pc0"
help
The pin to use for SPI data out to the device.
config ETRAX_SPI_MMC_CD_GPIO_PIN
string "MMC/SD card detect pin for SPI using gpio (space for none)"
depends on ETRAX_SPI_GPIO && MMC_SPI
default "pd11"
help
The pin to use for SD/MMC card detect. This pin should be pulled up
and grounded when a card is present. If defined as " " (space), no
pin is selected. A card must then always be inserted for proper
action.
config ETRAX_SPI_MMC_WP_GPIO_PIN
string "MMC/SD card write-protect pin for SPI using gpio (space for none)"
depends on ETRAX_SPI_GPIO && MMC_SPI
default "pd10"
help
The pin to use for the SD/MMC write-protect signal for a memory
card. If defined as " " (space), the card is considered writable.
endif

View File

@ -15,10 +15,6 @@ config ETRAX_SERIAL_PORTS
int
default 5
config ETRAX_DDR
bool
default y
config ETRAX_DDR2_MRS
hex "DDR2 MRS"
default "0"