forked from Minki/linux
dt-bindings: Use lower case hex in unit-addresses
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
This commit is contained in:
Rob Herring
parent
81ee6f1ef9
commit
afc3bca4cf
@ -55,7 +55,7 @@ Note: child nodes can be added for auto probing from device tree.
|
||||
|
||||
Example: adding device info in dtsi file
|
||||
|
||||
adc: adc@12D10000 {
|
||||
adc: adc@12d10000 {
|
||||
compatible = "samsung,exynos-adc-v1";
|
||||
reg = <0x12D10000 0x100>;
|
||||
interrupts = <0 106 0>;
|
||||
@ -71,7 +71,7 @@ adc: adc@12D10000 {
|
||||
|
||||
Example: adding device info in dtsi file for Exynos3250 with additional sclk
|
||||
|
||||
adc: adc@126C0000 {
|
||||
adc: adc@126c0000 {
|
||||
compatible = "samsung,exynos3250-adc", "samsung,exynos-adc-v2;
|
||||
reg = <0x126C0000 0x100>;
|
||||
interrupts = <0 137 0>;
|
||||
@ -87,7 +87,7 @@ adc: adc@126C0000 {
|
||||
|
||||
Example: Adding child nodes in dts file
|
||||
|
||||
adc@12D10000 {
|
||||
adc@12d10000 {
|
||||
|
||||
/* NTC thermistor is a hwmon device */
|
||||
ncp15wb473@0 {
|
||||
|
||||
@ -72,7 +72,7 @@ Optional nodes:
|
||||
- compatible: only "samsung,secure-firmware" is currently supported
|
||||
- reg: address of non-secure SYSRAM used for communication with firmware
|
||||
|
||||
firmware@203F000 {
|
||||
firmware@203f000 {
|
||||
compatible = "samsung,secure-firmware";
|
||||
reg = <0x0203F000 0x1000>;
|
||||
};
|
||||
|
||||
@ -32,7 +32,7 @@ Example 1: Examples of clock controller nodes are listed below.
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
|
||||
cmu_dmc: clock-controller@105C0000 {
|
||||
cmu_dmc: clock-controller@105c0000 {
|
||||
compatible = "samsung,exynos3250-cmu-dmc";
|
||||
reg = <0x105C0000 0x2000>;
|
||||
#clock-cells = <1>;
|
||||
|
||||
@ -180,7 +180,7 @@ Example 2: UART controller node that consumes the clock generated by the
|
||||
peri clock controller. Refer to the standard clock bindings for
|
||||
information about 'clocks' and 'clock-names' property.
|
||||
|
||||
serial@12C00000 {
|
||||
serial@12c00000 {
|
||||
compatible = "samsung,exynos4210-uart";
|
||||
reg = <0x12C00000 0x100>;
|
||||
interrupts = <0 146 0>;
|
||||
|
||||
@ -41,7 +41,7 @@ Example 2: UART controller node that consumes the clock generated by the clock
|
||||
controller. Refer to the standard clock bindings for information
|
||||
about 'clocks' and 'clock-names' property.
|
||||
|
||||
serial@12C20000 {
|
||||
serial@12c20000 {
|
||||
compatible = "samsung,exynos4210-uart";
|
||||
reg = <0x12C00000 0x100>;
|
||||
interrupts = <0 51 0>;
|
||||
|
||||
@ -472,7 +472,7 @@ Example 2: Examples of clock controller nodes are listed below.
|
||||
Example 3: UART controller node that consumes the clock generated by the clock
|
||||
controller.
|
||||
|
||||
serial_0: serial@14C10000 {
|
||||
serial_0: serial@14c10000 {
|
||||
compatible = "samsung,exynos5433-uart";
|
||||
reg = <0x14C10000 0x100>;
|
||||
interrupts = <0 421 0>;
|
||||
|
||||
@ -75,7 +75,7 @@ Required properties:
|
||||
- clock-frequency: must be present in the i2c controller node.
|
||||
|
||||
Example:
|
||||
atecc508a@C0 {
|
||||
atecc508a@c0 {
|
||||
compatible = "atmel,atecc508a";
|
||||
reg = <0xC0>;
|
||||
};
|
||||
|
||||
@ -20,7 +20,7 @@ Optional properties:
|
||||
|
||||
Example : NoC Probe nodes in Device Tree are listed below.
|
||||
|
||||
nocp_mem0_0: nocp@10CA1000 {
|
||||
nocp_mem0_0: nocp@10ca1000 {
|
||||
compatible = "samsung,exynos5420-nocp";
|
||||
reg = <0x10CA1000 0x200>;
|
||||
};
|
||||
|
||||
@ -54,7 +54,7 @@ Video interfaces:
|
||||
|
||||
Example:
|
||||
|
||||
dsi@11C80000 {
|
||||
dsi@11c80000 {
|
||||
compatible = "samsung,exynos4210-mipi-dsi";
|
||||
reg = <0x11C80000 0x10000>;
|
||||
interrupts = <0 79 0>;
|
||||
|
||||
@ -119,7 +119,7 @@ Example:
|
||||
/ {
|
||||
...
|
||||
|
||||
vtg_main_slave: sti-vtg-main-slave@fe85A800 {
|
||||
vtg_main_slave: sti-vtg-main-slave@fe85a800 {
|
||||
compatible = "st,vtg";
|
||||
reg = <0xfe85A800 0x300>;
|
||||
interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>;
|
||||
|
||||
@ -15,7 +15,7 @@ Optional properties:
|
||||
|
||||
Example:
|
||||
|
||||
dma: dma-controller@801C0000 {
|
||||
dma: dma-controller@801c0000 {
|
||||
compatible = "stericsson,db8500-dma40", "stericsson,dma40";
|
||||
reg = <0x801C0000 0x1000 0x40010000 0x800>;
|
||||
reg-names = "base", "lcpa";
|
||||
|
||||
@ -21,7 +21,7 @@ Documentation/devicetree/bindings/gpio/gpio.txt
|
||||
|
||||
Example:
|
||||
|
||||
gpioa: gpio@FF140000 {
|
||||
gpioa: gpio@ff140000 {
|
||||
compatible = "abilis,tb10x-gpio";
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
|
||||
@ -27,7 +27,7 @@ Optional properties:
|
||||
|
||||
Example:
|
||||
|
||||
gpio1: stp@E100BB0 {
|
||||
gpio1: stp@e100bb0 {
|
||||
compatible = "lantiq,gpio-stp-xway";
|
||||
reg = <0xE100BB0 0x40>;
|
||||
#gpio-cells = <2>;
|
||||
|
||||
@ -290,7 +290,7 @@ pins 50..69.
|
||||
|
||||
Example 2:
|
||||
|
||||
gpio_pio_i: gpio-controller@14B0 {
|
||||
gpio_pio_i: gpio-controller@14b0 {
|
||||
#gpio-cells = <2>;
|
||||
compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
|
||||
reg = <0x1480 0x18>;
|
||||
|
||||
@ -54,7 +54,7 @@ Optional properties:
|
||||
|
||||
|
||||
Example:
|
||||
i2c@12CA0000 {
|
||||
i2c@12ca0000 {
|
||||
compatible = "acme,some-i2c-device";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
@ -11,7 +11,7 @@ Required properties:
|
||||
|
||||
Examples:
|
||||
|
||||
lpi2c7: lpi2c7@40A50000 {
|
||||
lpi2c7: lpi2c7@40a50000 {
|
||||
compatible = "fsl,imx8dv-lpi2c";
|
||||
reg = <0x40A50000 0x10000>;
|
||||
interrupt-parent = <&intc>;
|
||||
|
||||
@ -45,7 +45,7 @@ Optional Properties specific to linux:
|
||||
|
||||
|
||||
Example:
|
||||
keypad@100A0000 {
|
||||
keypad@100a0000 {
|
||||
compatible = "samsung,s5pv210-keypad";
|
||||
reg = <0x100A0000 0x100>;
|
||||
interrupts = <173>;
|
||||
|
||||
@ -66,7 +66,7 @@ Example: An example of touchscreen node
|
||||
reg = <0x180a6000 0xc30>;
|
||||
};
|
||||
|
||||
touchscreen: touchscreen@180A6000 {
|
||||
touchscreen: touchscreen@180a6000 {
|
||||
compatible = "brcm,iproc-touchscreen";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
@ -56,7 +56,7 @@ Examples:
|
||||
iommus = <&sysmmu_gsc0>;
|
||||
};
|
||||
|
||||
sysmmu_gsc0: sysmmu@13E80000 {
|
||||
sysmmu_gsc0: sysmmu@13e80000 {
|
||||
compatible = "samsung,exynos-sysmmu";
|
||||
reg = <0x13E80000 0x1000>;
|
||||
interrupt-parent = <&combiner>;
|
||||
|
||||
@ -124,7 +124,7 @@ dsp {
|
||||
};
|
||||
|
||||
/* AM33xx */
|
||||
mailbox: mailbox@480C8000 {
|
||||
mailbox: mailbox@480c8000 {
|
||||
compatible = "ti,omap4-mailbox";
|
||||
reg = <0x480C8000 0x200>;
|
||||
interrupts = <77>;
|
||||
|
||||
@ -23,7 +23,7 @@ Optional:
|
||||
|
||||
Example:
|
||||
|
||||
hdmicec: cec@100B0000 {
|
||||
hdmicec: cec@100b0000 {
|
||||
compatible = "samsung,s5p-cec";
|
||||
reg = <0x100B0000 0x200>;
|
||||
interrupts = <0 114 0>;
|
||||
|
||||
@ -62,7 +62,7 @@ For more details see description of the SPI busses bindings
|
||||
|
||||
Example:
|
||||
|
||||
i2c@138A000000 {
|
||||
i2c@138a000000 {
|
||||
...
|
||||
s5c73m3@3c {
|
||||
compatible = "samsung,s5c73m3";
|
||||
|
||||
@ -138,7 +138,7 @@ from the corresponding HW reg.
|
||||
|
||||
Example for aemif, davinci nand and nor flash chip select shown below.
|
||||
|
||||
memory-controller@21000A00 {
|
||||
memory-controller@21000a00 {
|
||||
compatible = "ti,davinci-aemif";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <1>;
|
||||
|
||||
@ -41,7 +41,7 @@ Optional properties (all):
|
||||
|
||||
Example for I2C:
|
||||
|
||||
i2c@12CA0000 {
|
||||
i2c@12ca0000 {
|
||||
cros-ec@1e {
|
||||
reg = <0x1e>;
|
||||
compatible = "google,cros-ec-i2c";
|
||||
|
||||
@ -23,7 +23,7 @@ Optional subnodes:
|
||||
|
||||
Example:
|
||||
|
||||
mlc: flash@200A8000 {
|
||||
mlc: flash@200a8000 {
|
||||
compatible = "nxp,lpc3220-mlc";
|
||||
reg = <0x200A8000 0x11000>;
|
||||
interrupts = <11 0>;
|
||||
|
||||
@ -61,7 +61,7 @@ file.
|
||||
|
||||
Examples:
|
||||
|
||||
mac: ethernet@4A100000 {
|
||||
mac: ethernet@4a100000 {
|
||||
compatible = "ti,cpsw";
|
||||
reg = <0x4A100000 0x1000>;
|
||||
interrupts = <55 0x4>;
|
||||
@ -91,7 +91,7 @@ Examples:
|
||||
};
|
||||
|
||||
(or)
|
||||
mac: ethernet@4A100000 {
|
||||
mac: ethernet@4a100000 {
|
||||
compatible = "ti,cpsw";
|
||||
ti,hwmods = "cpgmac0";
|
||||
cpdma_channels = <8>;
|
||||
|
||||
@ -21,7 +21,7 @@ file.
|
||||
|
||||
Examples:
|
||||
|
||||
mdio: davinci_mdio@4A101000 {
|
||||
mdio: davinci_mdio@4a101000 {
|
||||
compatible = "ti,davinci_mdio";
|
||||
reg = <0x4A101000 0x1000>;
|
||||
bus_freq = <1000000>;
|
||||
@ -29,7 +29,7 @@ Examples:
|
||||
|
||||
(or)
|
||||
|
||||
mdio: davinci_mdio@4A101000 {
|
||||
mdio: davinci_mdio@4a101000 {
|
||||
compatible = "ti,davinci_mdio";
|
||||
ti,hwmods = "davinci_mdio";
|
||||
bus_freq = <1000000>;
|
||||
|
||||
@ -136,7 +136,7 @@ Clock Properties:
|
||||
|
||||
Example:
|
||||
|
||||
ptp_clock@24E00 {
|
||||
ptp_clock@24e00 {
|
||||
compatible = "fsl,etsec-ptp";
|
||||
reg = <0x24E00 0xB0>;
|
||||
interrupts = <12 0x8 13 0x8>;
|
||||
|
||||
@ -120,7 +120,7 @@ usb3phy@4a084400 {
|
||||
"refclk";
|
||||
};
|
||||
|
||||
sata_phy: phy@4A096000 {
|
||||
sata_phy: phy@4a096000 {
|
||||
compatible = "ti,phy-pipe3-sata";
|
||||
reg = <0x4A096000 0x80>, /* phy_rx */
|
||||
<0x4A096400 0x64>, /* phy_tx */
|
||||
|
||||
@ -49,7 +49,7 @@ explained in Documentation/devicetree/bindings/gpio/gpio.txt.
|
||||
Example
|
||||
-------
|
||||
|
||||
iomux: iomux@FF10601c {
|
||||
iomux: iomux@ff10601c {
|
||||
compatible = "abilis,tb10x-iomux";
|
||||
reg = <0xFF10601c 0x4>;
|
||||
pctl_gpio_a: pctl-gpio-a {
|
||||
@ -59,7 +59,7 @@ iomux: iomux@FF10601c {
|
||||
abilis,function = "uart0";
|
||||
};
|
||||
};
|
||||
uart@FF100000 {
|
||||
uart@ff100000 {
|
||||
compatible = "snps,dw-apb-uart";
|
||||
reg = <0xFF100000 0x100>;
|
||||
clock-frequency = <166666666>;
|
||||
@ -69,7 +69,7 @@ uart@FF100000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pctl_uart0>;
|
||||
};
|
||||
gpioa: gpio@FF140000 {
|
||||
gpioa: gpio@ff140000 {
|
||||
compatible = "abilis,tb10x-gpio";
|
||||
reg = <0xFF140000 0x1000>;
|
||||
gpio-controller;
|
||||
|
||||
@ -152,7 +152,7 @@ resetn
|
||||
|
||||
Example:
|
||||
--------
|
||||
pinctrl@18101C00 {
|
||||
pinctrl@18101c00 {
|
||||
compatible = "img,pistachio-system-pinctrl";
|
||||
reg = <0x18101C00 0x400>;
|
||||
|
||||
|
||||
@ -163,7 +163,7 @@ Valid values for xRX300 pin names:
|
||||
io42-io43,io48-io61.
|
||||
|
||||
Example:
|
||||
gpio: pinmux@E100B10 {
|
||||
gpio: pinmux@e100b10 {
|
||||
compatible = "lantiq,danube-pinctrl";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&state_default>;
|
||||
|
||||
@ -81,7 +81,7 @@ Examples:
|
||||
reg = <0 0x10005000 0 0x1000>;
|
||||
};
|
||||
|
||||
syscfg_pctl_b: syscfg_pctl_b@1020C020 {
|
||||
syscfg_pctl_b: syscfg_pctl_b@1020c020 {
|
||||
compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
|
||||
reg = <0 0x1020C020 0 0x1000>;
|
||||
};
|
||||
|
||||
@ -223,37 +223,37 @@ lac-portals {
|
||||
reg = <0x9000 0x1000>;
|
||||
};
|
||||
|
||||
lportal10: lac-portal@A000 {
|
||||
lportal10: lac-portal@a000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x20E>;
|
||||
reg = <0xA000 0x1000>;
|
||||
};
|
||||
|
||||
lportal11: lac-portal@B000 {
|
||||
lportal11: lac-portal@b000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x20F>;
|
||||
reg = <0xB000 0x1000>;
|
||||
};
|
||||
|
||||
lportal12: lac-portal@C000 {
|
||||
lportal12: lac-portal@c000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x210>;
|
||||
reg = <0xC000 0x1000>;
|
||||
};
|
||||
|
||||
lportal13: lac-portal@D000 {
|
||||
lportal13: lac-portal@d000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x211>;
|
||||
reg = <0xD000 0x1000>;
|
||||
};
|
||||
|
||||
lportal14: lac-portal@E000 {
|
||||
lportal14: lac-portal@e000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x212>;
|
||||
reg = <0xE000 0x1000>;
|
||||
};
|
||||
|
||||
lportal15: lac-portal@F000 {
|
||||
lportal15: lac-portal@f000 {
|
||||
compatible = "fsl,interlaken-lac-portal-v1.0";
|
||||
fsl,liodn = <0x213>;
|
||||
reg = <0xF000 0x1000>;
|
||||
|
||||
@ -10,7 +10,7 @@ Required properties:
|
||||
- clocks: Must contain an entry for peripheral clock.
|
||||
|
||||
Example:
|
||||
vrefbuf: regulator@58003C00 {
|
||||
vrefbuf: regulator@58003c00 {
|
||||
compatible = "st,stm32-vrefbuf";
|
||||
reg = <0x58003C00 0x8>;
|
||||
clocks = <&rcc VREF_CK>;
|
||||
|
||||
@ -8,7 +8,7 @@ Required properties:
|
||||
|
||||
Example:
|
||||
|
||||
asc1: serial@E100C00 {
|
||||
asc1: serial@e100c00 {
|
||||
compatible = "lantiq,asc";
|
||||
reg = <0xE100C00 0x400>;
|
||||
interrupt-parent = <&icu0>;
|
||||
|
||||
@ -35,7 +35,7 @@ Optional Properties:
|
||||
|
||||
Example:
|
||||
|
||||
i2s_out: i2s-out@18100A00 {
|
||||
i2s_out: i2s-out@18100a00 {
|
||||
compatible = "img,i2s-out";
|
||||
reg = <0x18100A00 0x200>;
|
||||
interrupts = <GIC_SHARED 13 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
@ -29,7 +29,7 @@ Optional Properties:
|
||||
|
||||
Example:
|
||||
|
||||
parallel_out: parallel-out@18100C00 {
|
||||
parallel_out: parallel-out@18100c00 {
|
||||
compatible = "img,parallel-out";
|
||||
reg = <0x18100C00 0x100>;
|
||||
interrupts = <GIC_SHARED 19 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
@ -29,7 +29,7 @@ Optional Properties:
|
||||
|
||||
Example:
|
||||
|
||||
spdif_in: spdif-in@18100E00 {
|
||||
spdif_in: spdif-in@18100e00 {
|
||||
compatible = "img,spdif-in";
|
||||
reg = <0x18100E00 0x100>;
|
||||
interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
@ -29,7 +29,7 @@ Optional Properties:
|
||||
|
||||
Example:
|
||||
|
||||
spdif_out: spdif-out@18100D00 {
|
||||
spdif_out: spdif-out@18100d00 {
|
||||
compatible = "img,spdif-out";
|
||||
reg = <0x18100D00 0x100>;
|
||||
interrupts = <GIC_SHARED 21 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
@ -51,7 +51,7 @@ Optional properties:
|
||||
|
||||
Example:
|
||||
|
||||
sti_uni_player1: sti-uni-player@8D81000 {
|
||||
sti_uni_player1: sti-uni-player@8d81000 {
|
||||
compatible = "st,stih407-uni-player-hdmi";
|
||||
#sound-dai-cells = <0>;
|
||||
st,syscfg = <&syscfg_core>;
|
||||
@ -63,7 +63,7 @@ Example:
|
||||
st,tdm-mode = <1>;
|
||||
};
|
||||
|
||||
sti_uni_player2: sti-uni-player@8D82000 {
|
||||
sti_uni_player2: sti-uni-player@8d82000 {
|
||||
compatible = "st,stih407-uni-player-pcm-out";
|
||||
#sound-dai-cells = <0>;
|
||||
st,syscfg = <&syscfg_core>;
|
||||
@ -74,7 +74,7 @@ Example:
|
||||
dma-names = "tx";
|
||||
};
|
||||
|
||||
sti_uni_player3: sti-uni-player@8D85000 {
|
||||
sti_uni_player3: sti-uni-player@8d85000 {
|
||||
compatible = "st,stih407-uni-player-spdif";
|
||||
#sound-dai-cells = <0>;
|
||||
st,syscfg = <&syscfg_core>;
|
||||
@ -85,7 +85,7 @@ Example:
|
||||
dma-names = "tx";
|
||||
};
|
||||
|
||||
sti_uni_reader1: sti-uni-reader@8D84000 {
|
||||
sti_uni_reader1: sti-uni-reader@8d84000 {
|
||||
compatible = "st,stih407-uni-reader-hdmi";
|
||||
#sound-dai-cells = <0>;
|
||||
st,syscfg = <&syscfg_core>;
|
||||
|
||||
@ -68,7 +68,7 @@ SPI_SOMI/SIMO+-----------------+ +-----------
|
||||
Example of a NOR flash slave device (n25q032) connected to DaVinci
|
||||
SPI controller device over the SPI bus.
|
||||
|
||||
spi0:spi@20BF0000 {
|
||||
spi0:spi@20bf0000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "ti,dm6446-spi";
|
||||
|
||||
@ -16,7 +16,7 @@ Optional properties:
|
||||
Example:
|
||||
|
||||
|
||||
spi: spi@E100800 {
|
||||
spi: spi@e100800 {
|
||||
compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi";
|
||||
reg = <0xE100800 0x100>;
|
||||
interrupt-parent = <&icu0>;
|
||||
|
||||
@ -70,7 +70,7 @@ Following properties are mandatory (depending on SoC):
|
||||
|
||||
Example 1):
|
||||
|
||||
tmu@100C0000 {
|
||||
tmu@100c0000 {
|
||||
compatible = "samsung,exynos4412-tmu";
|
||||
interrupt-parent = <&combiner>;
|
||||
reg = <0x100C0000 0x100>;
|
||||
|
||||
@ -252,7 +252,7 @@ ocp {
|
||||
/*
|
||||
* A simple IC with a single bandgap temperature sensor.
|
||||
*/
|
||||
bandgap0: bandgap@0000ED00 {
|
||||
bandgap0: bandgap@0000ed00 {
|
||||
...
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
@ -330,7 +330,7 @@ ocp {
|
||||
/*
|
||||
* A simple IC with several bandgap temperature sensors.
|
||||
*/
|
||||
bandgap0: bandgap@0000ED00 {
|
||||
bandgap0: bandgap@0000ed00 {
|
||||
...
|
||||
#thermal-sensor-cells = <1>;
|
||||
};
|
||||
@ -458,7 +458,7 @@ ocp {
|
||||
/*
|
||||
* A simple IC with a single bandgap temperature sensor.
|
||||
*/
|
||||
bandgap0: bandgap@0000ED00 {
|
||||
bandgap0: bandgap@0000ed00 {
|
||||
...
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
|
||||
@ -51,7 +51,7 @@ Example 2: In this example, the timer interrupts are connected to two separate
|
||||
interrupt controllers. Hence, an interrupt-map is created to map
|
||||
the interrupts to the respective interrupt controllers.
|
||||
|
||||
mct@101C0000 {
|
||||
mct@101c0000 {
|
||||
compatible = "samsung,exynos4210-mct";
|
||||
reg = <0x101C0000 0x800>;
|
||||
interrupt-parent = <&mct_map>;
|
||||
|
||||
@ -10,7 +10,7 @@ Optional properties:
|
||||
|
||||
Example:
|
||||
|
||||
watchdog@4003C000 {
|
||||
watchdog@4003c000 {
|
||||
compatible = "nxp,pnx4008-wdt";
|
||||
reg = <0x4003C000 0x1000>;
|
||||
timeout-sec = <10>;
|
||||
|
||||
@ -25,7 +25,7 @@ Optional properties:
|
||||
|
||||
Example:
|
||||
|
||||
watchdog@101D0000 {
|
||||
watchdog@101d0000 {
|
||||
compatible = "samsung,exynos5250-wdt";
|
||||
reg = <0x101D0000 0x100>;
|
||||
interrupts = <0 42 0>;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user