forked from Minki/linux
dt-bindings: Fix unbalanced quotation marks
Multiple binding documents have various forms of unbalanced quotation marks. Fix them. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
This commit is contained in:
Jonathan Neuschäfer
Rob Herring
parent
5bfabc0aab
commit
a47c9b3943
@ -66,7 +66,7 @@ Required root node properties:
|
||||
- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
|
||||
Octa board.
|
||||
- "insignal,origen" - for Exynos4210-based Insignal Origen board.
|
||||
- "insignal,origen4412 - for Exynos4412-based Insignal Origen board.
|
||||
- "insignal,origen4412" - for Exynos4412-based Insignal Origen board.
|
||||
|
||||
|
||||
Optional nodes:
|
||||
|
||||
@ -1,7 +1,7 @@
|
||||
Nintendo Wii (Hollywood) GPIO controller
|
||||
|
||||
Required properties:
|
||||
- compatible: "nintendo,hollywood-gpio
|
||||
- compatible: "nintendo,hollywood-gpio"
|
||||
- reg: Physical base address and length of the controller's registers.
|
||||
- gpio-controller: Marks the device node as a GPIO controller.
|
||||
- #gpio-cells: Should be <2>. The first cell is the pin number and the
|
||||
|
||||
@ -32,7 +32,7 @@ i2c@00000000 {
|
||||
reg = <0x6c>;
|
||||
interrupt-parent = <&gpx1>;
|
||||
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
||||
vdd-supply = <&ldo15_reg>";
|
||||
vdd-supply = <&ldo15_reg>;
|
||||
vid-supply = <&ldo18_reg>;
|
||||
reset-gpios = <&gpx1 5 0>;
|
||||
touchscreen-size-x = <1080>;
|
||||
|
||||
@ -15,7 +15,7 @@ Required properties:
|
||||
include "nvidia,tegra30-ictlr".
|
||||
- reg : Specifies base physical address and size of the registers.
|
||||
Each controller must be described separately (Tegra20 has 4 of them,
|
||||
whereas Tegra30 and later have 5"
|
||||
whereas Tegra30 and later have 5).
|
||||
- interrupt-controller : Identifies the node as an interrupt controller.
|
||||
- #interrupt-cells : Specifies the number of cells needed to encode an
|
||||
interrupt source. The value must be 3.
|
||||
|
||||
@ -12,7 +12,7 @@ Required properties:
|
||||
specifier, shall be 2
|
||||
- interrupts: interrupts references to primary interrupt controller
|
||||
(only needed for exti controller with multiple exti under
|
||||
same parent interrupt: st,stm32-exti and st,stm32h7-exti")
|
||||
same parent interrupt: st,stm32-exti and st,stm32h7-exti)
|
||||
|
||||
Example:
|
||||
|
||||
|
||||
@ -152,7 +152,7 @@ Required properties:
|
||||
- compatible : should contain one of:
|
||||
"brcm,bcm7425-timers"
|
||||
"brcm,bcm7429-timers"
|
||||
"brcm,bcm7435-timers and
|
||||
"brcm,bcm7435-timers" and
|
||||
"brcm,brcmstb-timers"
|
||||
- reg : the timers register range
|
||||
- interrupts : the interrupt line for this timer block
|
||||
|
||||
@ -238,7 +238,7 @@ PROPERTIES
|
||||
Must include one of the following:
|
||||
- "fsl,fman-dtsec" for dTSEC MAC
|
||||
- "fsl,fman-xgec" for XGEC MAC
|
||||
- "fsl,fman-memac for mEMAC MAC
|
||||
- "fsl,fman-memac" for mEMAC MAC
|
||||
|
||||
- cell-index
|
||||
Usage: required
|
||||
|
||||
@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
|
||||
node with the label "power".
|
||||
In the second example the consumer device are partitioned across two PM domains,
|
||||
the first with index 0 and the second with index 1, of a power controller that
|
||||
is represented by a node with the label "power.
|
||||
is represented by a node with the label "power".
|
||||
|
||||
Optional properties:
|
||||
- required-opps: This contains phandle to an OPP node in another device's OPP
|
||||
|
||||
@ -16,7 +16,7 @@ Required properties:
|
||||
Optional properties:
|
||||
- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
If DCDCs are externally controlled then this property should be there.
|
||||
- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
If DCDCs are externally controlled and if it is from GPIO then GPIO
|
||||
number should be provided. If it is externally controlled and no GPIO
|
||||
entry then driver will just configure this rails as external control
|
||||
|
||||
@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
|
||||
controller binding usage.
|
||||
|
||||
Required properties:
|
||||
- compatible: Should be st,stih407-softreset";
|
||||
- compatible: Should be "st,stih407-softreset";
|
||||
- #reset-cells: 1, see below
|
||||
|
||||
example:
|
||||
|
||||
@ -30,7 +30,7 @@ Required properties:
|
||||
|
||||
Board connectors:
|
||||
* Headset Mic
|
||||
* Secondary Mic",
|
||||
* Secondary Mic
|
||||
* DMIC
|
||||
* Ext Spk
|
||||
|
||||
|
||||
@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
|
||||
"Digital Mic3"
|
||||
|
||||
Audio pins and MicBias on WCD9335 Codec:
|
||||
"MIC_BIAS1
|
||||
"MIC_BIAS1"
|
||||
"MIC_BIAS2"
|
||||
"MIC_BIAS3"
|
||||
"MIC_BIAS4"
|
||||
|
||||
Loading…
Reference in New Issue
Block a user