ARM: dts: Use labels for overriding nodes in exynos4210-trats

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit is contained in:
Krzysztof Kozlowski 2015-04-06 21:01:17 +02:00 committed by Kukjin Kim
parent bad0b9c9ab
commit 9b70afd9ea

View File

@ -89,42 +89,6 @@
};
};
hsotg@12480000 {
vusb_d-supply = <&vusb_reg>;
vusb_a-supply = <&vusbdac_reg>;
dr_mode = "peripheral";
status = "okay";
};
sdhci_emmc: sdhci@12510000 {
bus-width = <8>;
non-removable;
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
pinctrl-names = "default";
vmmc-supply = <&vemmc_reg>;
status = "okay";
};
exynos-usbphy@125B0000 {
status = "okay";
};
serial@13800000 {
status = "okay";
};
serial@13810000 {
status = "okay";
};
serial@13820000 {
status = "okay";
};
serial@13830000 {
status = "okay";
};
gpio-keys {
compatible = "gpio-keys";
@ -158,201 +122,6 @@
};
};
i2c@13890000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <400000>;
pinctrl-0 = <&i2c3_bus>;
pinctrl-names = "default";
status = "okay";
mms114-touchscreen@48 {
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpx0>;
interrupts = <4 2>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&tsp_reg>;
vdd-supply = <&tsp_reg>;
};
};
i2c@138B0000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
pinctrl-0 = <&i2c5_bus>;
pinctrl-names = "default";
status = "okay";
max8997_pmic@66 {
compatible = "maxim,max8997-pmic";
reg = <0x66>;
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
max8997,pmic-buck5-uses-gpio-dvs;
max8997,pmic-ignore-gpiodvs-side-effect;
max8997,pmic-buck125-default-dvs-idx = <0>;
max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
<&gpx0 6 0>,
<&gpl0 0 0>;
max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
<1250000>, <1200000>,
<1150000>, <1100000>,
<1000000>, <950000>;
max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
<950000>, <900000>,
<1100000>, <1000000>,
<950000>, <900000>;
max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>;
regulators {
valive_reg: LDO2 {
regulator-name = "VALIVE_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
vusb_reg: LDO3 {
regulator-name = "VUSB_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
vmipi_reg: LDO4 {
regulator-name = "VMIPI_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vpda_reg: LDO6 {
regulator-name = "VCC_1.8V_PDA";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vcam_reg: LDO7 {
regulator-name = "CAM_ISP_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vusbdac_reg: LDO8 {
regulator-name = "VUSB/VDAC_3.3V_C210";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vccpda_reg: LDO9 {
regulator-name = "VCC_2.8V_PDA";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
vpll_reg: LDO10 {
regulator-name = "VPLL_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
vtcam_reg: LDO12 {
regulator-name = "VT_CAM_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vcclcd_reg: LDO13 {
regulator-name = "VCC_3.3V_LCD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vlcd_reg: LDO15 {
regulator-name = "VLCD_2.2V";
regulator-min-microvolt = <2200000>;
regulator-max-microvolt = <2200000>;
};
camsensor_reg: LDO16 {
regulator-name = "CAM_SENSOR_IO_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddq_reg: LDO21 {
regulator-name = "VDDQ_M1M2_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
varm_breg: BUCK1 {
/*
* HACK: The real name is VARM_1.2V_C210,
* but exynos-cpufreq does not support
* DT-based regulator lookup yet.
*/
regulator-name = "vdd_arm";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
vint_breg: BUCK2 {
regulator-name = "VINT_1.1V_C210";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
camisp_breg: BUCK4 {
regulator-name = "CAM_ISP_CORE_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
vmem_breg: BUCK5 {
regulator-name = "VMEM_1.2V_C210";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vccsub_breg: BUCK7 {
regulator-name = "VCC_SUB_2.0V";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
regulator-always-on;
};
safe1_sreg: ESAFEOUT1 {
regulator-name = "SAFEOUT1";
regulator-always-on;
};
safe2_sreg: ESAFEOUT2 {
regulator-name = "SAFEOUT2";
regulator-boot-on;
};
};
};
};
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@ -365,71 +134,6 @@
};
};
dsi_0: dsi@11C80000 {
vddcore-supply = <&vusb_reg>;
vddio-supply = <&vmipi_reg>;
samsung,pll-clock-frequency = <24000000>;
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
dsi_out: endpoint {
remote-endpoint = <&dsi_in>;
samsung,burst-clock-frequency = <500000000>;
samsung,esc-clock-frequency = <20000000>;
};
};
};
panel@0 {
reg = <0>;
compatible = "samsung,s6e8aa0";
vdd3-supply = <&vcclcd_reg>;
vci-supply = <&vlcd_reg>;
reset-gpios = <&gpy4 5 0>;
power-on-delay= <50>;
reset-delay = <100>;
init-delay = <100>;
flip-horizontal;
flip-vertical;
panel-width-mm = <58>;
panel-height-mm = <103>;
display-timings {
timing-0 {
clock-frequency = <57153600>;
hactive = <720>;
vactive = <1280>;
hfront-porch = <5>;
hback-porch = <5>;
hsync-len = <5>;
vfront-porch = <13>;
vback-porch = <1>;
vsync-len = <2>;
};
};
port {
dsi_in: endpoint {
remote-endpoint = <&dsi_out>;
};
};
};
};
fimd@11c00000 {
status = "okay";
};
tmu@100C0000 {
status = "okay";
};
thermal-zones {
cpu_thermal: cpu-thermal {
cooling-maps {
@ -483,3 +187,299 @@
};
};
};
&dsi_0 {
vddcore-supply = <&vusb_reg>;
vddio-supply = <&vmipi_reg>;
samsung,pll-clock-frequency = <24000000>;
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
dsi_out: endpoint {
remote-endpoint = <&dsi_in>;
samsung,burst-clock-frequency = <500000000>;
samsung,esc-clock-frequency = <20000000>;
};
};
};
panel@0 {
reg = <0>;
compatible = "samsung,s6e8aa0";
vdd3-supply = <&vcclcd_reg>;
vci-supply = <&vlcd_reg>;
reset-gpios = <&gpy4 5 0>;
power-on-delay= <50>;
reset-delay = <100>;
init-delay = <100>;
flip-horizontal;
flip-vertical;
panel-width-mm = <58>;
panel-height-mm = <103>;
display-timings {
timing-0 {
clock-frequency = <57153600>;
hactive = <720>;
vactive = <1280>;
hfront-porch = <5>;
hback-porch = <5>;
hsync-len = <5>;
vfront-porch = <13>;
vback-porch = <1>;
vsync-len = <2>;
};
};
port {
dsi_in: endpoint {
remote-endpoint = <&dsi_out>;
};
};
};
};
&exynos_usbphy {
status = "okay";
};
&fimd {
status = "okay";
};
&hsotg {
vusb_d-supply = <&vusb_reg>;
vusb_a-supply = <&vusbdac_reg>;
dr_mode = "peripheral";
status = "okay";
};
&i2c_3 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <400000>;
pinctrl-0 = <&i2c3_bus>;
pinctrl-names = "default";
status = "okay";
mms114-touchscreen@48 {
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpx0>;
interrupts = <4 2>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&tsp_reg>;
vdd-supply = <&tsp_reg>;
};
};
&i2c_5 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
pinctrl-0 = <&i2c5_bus>;
pinctrl-names = "default";
status = "okay";
max8997_pmic@66 {
compatible = "maxim,max8997-pmic";
reg = <0x66>;
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
max8997,pmic-buck5-uses-gpio-dvs;
max8997,pmic-ignore-gpiodvs-side-effect;
max8997,pmic-buck125-default-dvs-idx = <0>;
max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
<&gpx0 6 0>,
<&gpl0 0 0>;
max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
<1250000>, <1200000>,
<1150000>, <1100000>,
<1000000>, <950000>;
max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
<950000>, <900000>,
<1100000>, <1000000>,
<950000>, <900000>;
max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>;
regulators {
valive_reg: LDO2 {
regulator-name = "VALIVE_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
vusb_reg: LDO3 {
regulator-name = "VUSB_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
vmipi_reg: LDO4 {
regulator-name = "VMIPI_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vpda_reg: LDO6 {
regulator-name = "VCC_1.8V_PDA";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vcam_reg: LDO7 {
regulator-name = "CAM_ISP_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vusbdac_reg: LDO8 {
regulator-name = "VUSB/VDAC_3.3V_C210";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vccpda_reg: LDO9 {
regulator-name = "VCC_2.8V_PDA";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
vpll_reg: LDO10 {
regulator-name = "VPLL_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
vtcam_reg: LDO12 {
regulator-name = "VT_CAM_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vcclcd_reg: LDO13 {
regulator-name = "VCC_3.3V_LCD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vlcd_reg: LDO15 {
regulator-name = "VLCD_2.2V";
regulator-min-microvolt = <2200000>;
regulator-max-microvolt = <2200000>;
};
camsensor_reg: LDO16 {
regulator-name = "CAM_SENSOR_IO_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddq_reg: LDO21 {
regulator-name = "VDDQ_M1M2_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
varm_breg: BUCK1 {
/*
* HACK: The real name is VARM_1.2V_C210,
* but exynos-cpufreq does not support
* DT-based regulator lookup yet.
*/
regulator-name = "vdd_arm";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
vint_breg: BUCK2 {
regulator-name = "VINT_1.1V_C210";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
camisp_breg: BUCK4 {
regulator-name = "CAM_ISP_CORE_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
vmem_breg: BUCK5 {
regulator-name = "VMEM_1.2V_C210";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vccsub_breg: BUCK7 {
regulator-name = "VCC_SUB_2.0V";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
regulator-always-on;
};
safe1_sreg: ESAFEOUT1 {
regulator-name = "SAFEOUT1";
regulator-always-on;
};
safe2_sreg: ESAFEOUT2 {
regulator-name = "SAFEOUT2";
regulator-boot-on;
};
};
};
};
&sdhci_0 {
bus-width = <8>;
non-removable;
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
pinctrl-names = "default";
vmmc-supply = <&vemmc_reg>;
status = "okay";
};
&serial_0 {
status = "okay";
};
&serial_1 {
status = "okay";
};
&serial_2 {
status = "okay";
};
&serial_3 {
status = "okay";
};
&tmu {
status = "okay";
};