diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 8d999d862d0e..79f533f38c61 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1238,1122 +1238,7 @@ descriptions for the SOC devices for which new nodes have been defined; this list will expand as more and more SOC-containing platforms are moved over to use the flattened-device-tree model. - a) PHY nodes - - Required properties: - - - device_type : Should be "ethernet-phy" - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - linux,phandle : phandle for this node; likely referenced by an - ethernet controller node. - - - Example: - - ethernet-phy@0 { - linux,phandle = <2452000> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <0>; - device_type = "ethernet-phy"; - }; - - - b) Interrupt controllers - - Some SOC devices contain interrupt controllers that are different - from the standard Open PIC specification. The SOC device nodes for - these types of controllers should be specified just like a standard - OpenPIC controller. Sense and level information should be encoded - as specified in section 2) of this chapter for each device that - specifies an interrupt. - - Example : - - pic@40000 { - linux,phandle = <40000>; - interrupt-controller; - #address-cells = <0>; - reg = <40000 40000>; - compatible = "chrp,open-pic"; - device_type = "open-pic"; - }; - - c) 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : - - interrupt-parent : optional, if needed for interrupt mapping - - reg : - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - Example: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : . - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a - - d) Xilinx IP cores - - The Xilinx EDK toolchain ships with a set of IP cores (devices) for use - in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range - of standard device types (network, serial, etc.) and miscellaneous - devices (gpio, LCD, spi, etc). Also, since these devices are - implemented within the fpga fabric every instance of the device can be - synthesised with different options that change the behaviour. - - Each IP-core has a set of parameters which the FPGA designer can use to - control how the core is synthesized. Historically, the EDK tool would - extract the device parameters relevant to device drivers and copy them - into an 'xparameters.h' in the form of #define symbols. This tells the - device drivers how the IP cores are configured, but it requres the kernel - to be recompiled every time the FPGA bitstream is resynthesized. - - The new approach is to export the parameters into the device tree and - generate a new device tree each time the FPGA bitstream changes. The - parameters which used to be exported as #defines will now become - properties of the device node. In general, device nodes for IP-cores - will take the following form: - - (name): (generic-name)@(base-address) { - compatible = "xlnx,(ip-core-name)-(HW_VER)" - [, (list of compatible devices), ...]; - reg = <(baseaddr) (size)>; - interrupt-parent = <&interrupt-controller-phandle>; - interrupts = < ... >; - xlnx,(parameter1) = "(string-value)"; - xlnx,(parameter2) = <(int-value)>; - }; - - (generic-name): an open firmware-style name that describes the - generic class of device. Preferably, this is one word, such - as 'serial' or 'ethernet'. - (ip-core-name): the name of the ip block (given after the BEGIN - directive in system.mhs). Should be in lowercase - and all underscores '_' converted to dashes '-'. - (name): is derived from the "PARAMETER INSTANCE" value. - (parameter#): C_* parameters from system.mhs. The C_ prefix is - dropped from the parameter name, the name is converted - to lowercase and all underscore '_' characters are - converted to dashes '-'. - (baseaddr): the baseaddr parameter value (often named C_BASEADDR). - (HW_VER): from the HW_VER parameter. - (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). - - Typically, the compatible list will include the exact IP core version - followed by an older IP core version which implements the same - interface or any other device with the same interface. - - 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. - - For example, the following block from system.mhs: - - BEGIN opb_uartlite - PARAMETER INSTANCE = opb_uartlite_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BAUDRATE = 115200 - PARAMETER C_DATA_BITS = 8 - PARAMETER C_ODD_PARITY = 0 - PARAMETER C_USE_PARITY = 0 - PARAMETER C_CLK_FREQ = 50000000 - PARAMETER C_BASEADDR = 0xEC100000 - PARAMETER C_HIGHADDR = 0xEC10FFFF - BUS_INTERFACE SOPB = opb_7 - PORT OPB_Clk = CLK_50MHz - PORT Interrupt = opb_uartlite_0_Interrupt - PORT RX = opb_uartlite_0_RX - PORT TX = opb_uartlite_0_TX - PORT OPB_Rst = sys_bus_reset_0 - END - - becomes the following device tree node: - - opb_uartlite_0: serial@ec100000 { - device_type = "serial"; - compatible = "xlnx,opb-uartlite-1.00.b"; - reg = ; - interrupt-parent = <&opb_intc_0>; - interrupts = <1 0>; // got this from the opb_intc parameters - current-speed = ; // standard serial device prop - clock-frequency = ; // standard serial device prop - xlnx,data-bits = <8>; - xlnx,odd-parity = <0>; - xlnx,use-parity = <0>; - }; - - Some IP cores actually implement 2 or more logical devices. In - this case, the device should still describe the whole IP core with - a single node and add a child node for each logical device. The - ranges property can be used to translate from parent IP-core to the - registers of each device. In addition, the parent node should be - compatible with the bus type 'xlnx,compound', and should contain - #address-cells and #size-cells, as with any other bus. (Note: this - makes the assumption that both logical devices have the same bus - binding. If this is not true, then separate nodes should be used - for each logical device). The 'cell-index' property can be used to - enumerate logical devices within an IP core. For example, the - following is the system.mhs entry for the dual ps2 controller found - on the ml403 reference design. - - BEGIN opb_ps2_dual_ref - PARAMETER INSTANCE = opb_ps2_dual_ref_0 - PARAMETER HW_VER = 1.00.a - PARAMETER C_BASEADDR = 0xA9000000 - PARAMETER C_HIGHADDR = 0xA9001FFF - BUS_INTERFACE SOPB = opb_v20_0 - PORT Sys_Intr1 = ps2_1_intr - PORT Sys_Intr2 = ps2_2_intr - PORT Clkin1 = ps2_clk_rx_1 - PORT Clkin2 = ps2_clk_rx_2 - PORT Clkpd1 = ps2_clk_tx_1 - PORT Clkpd2 = ps2_clk_tx_2 - PORT Rx1 = ps2_d_rx_1 - PORT Rx2 = ps2_d_rx_2 - PORT Txpd1 = ps2_d_tx_1 - PORT Txpd2 = ps2_d_tx_2 - END - - It would result in the following device tree nodes: - - opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,compound"; - ranges = <0 a9000000 2000>; - // If this device had extra parameters, then they would - // go here. - ps2@0 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <0 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - ps2@1000 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <1000 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - }; - - Also, the system.mhs file defines bus attachments from the processor - to the devices. The device tree structure should reflect the bus - attachments. Again an example; this system.mhs fragment: - - BEGIN ppc405_virtex4 - PARAMETER INSTANCE = ppc405_0 - PARAMETER HW_VER = 1.01.a - BUS_INTERFACE DPLB = plb_v34_0 - BUS_INTERFACE IPLB = plb_v34_0 - END - - BEGIN opb_intc - PARAMETER INSTANCE = opb_intc_0 - PARAMETER HW_VER = 1.00.c - PARAMETER C_BASEADDR = 0xD1000FC0 - PARAMETER C_HIGHADDR = 0xD1000FDF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN opb_uart16550 - PARAMETER INSTANCE = opb_uart16550_0 - PARAMETER HW_VER = 1.00.d - PARAMETER C_BASEADDR = 0xa0000000 - PARAMETER C_HIGHADDR = 0xa0001FFF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN plb_v34 - PARAMETER INSTANCE = plb_v34_0 - PARAMETER HW_VER = 1.02.a - END - - BEGIN plb_bram_if_cntlr - PARAMETER INSTANCE = plb_bram_if_cntlr_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BASEADDR = 0xFFFF0000 - PARAMETER C_HIGHADDR = 0xFFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - END - - BEGIN plb2opb_bridge - PARAMETER INSTANCE = plb2opb_bridge_0 - PARAMETER HW_VER = 1.01.a - PARAMETER C_RNG0_BASEADDR = 0x20000000 - PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF - PARAMETER C_RNG1_BASEADDR = 0x60000000 - PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF - PARAMETER C_RNG2_BASEADDR = 0x80000000 - PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF - PARAMETER C_RNG3_BASEADDR = 0xC0000000 - PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - BUS_INTERFACE MOPB = opb_v20_0 - END - - Gives this device tree (some properties removed for clarity): - - plb@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,plb-v34-1.02.a"; - device_type = "ibm,plb"; - ranges; // 1:1 translation - - plb_bram_if_cntrl_0: bram@ffff0000 { - reg = ; - } - - opb@20000000 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <20000000 20000000 20000000 - 60000000 60000000 20000000 - 80000000 80000000 40000000 - c0000000 c0000000 20000000>; - - opb_uart16550_0: serial@a0000000 { - reg = ; - }; - - opb_intc_0: interrupt-controller@d1000fc0 { - reg = ; - }; - }; - }; - - That covers the general approach to binding xilinx IP cores into the - device tree. The following are bindings for specific devices: - - i) Xilinx ML300 Framebuffer - - Simple framebuffer device from the ML300 reference design (also on the - ML403 reference design as well as others). - - Optional properties: - - resolution = : pixel resolution of framebuffer. Some - implementations use a different resolution. - Default is - - virt-resolution = : Size of framebuffer in memory. - Default is . - - rotate-display (empty) : rotate display 180 degrees. - - ii) Xilinx SystemACE - - The Xilinx SystemACE device is used to program FPGAs from an FPGA - bitstream stored on a CF card. It can also be used as a generic CF - interface device. - - Optional properties: - - 8-bit (empty) : Set this property for SystemACE in 8 bit mode - - iii) Xilinx EMAC and Xilinx TEMAC - - Xilinx Ethernet devices. In addition to general xilinx properties - listed above, nodes for these devices should include a phy-handle - property, and may include other common network device properties - like local-mac-address. - - iv) Xilinx Uartlite - - Xilinx uartlite devices are simple fixed speed serial ports. - - Required properties: - - current-speed : Baud rate of uartlite - - v) Xilinx hwicap - - Xilinx hwicap devices provide access to the configuration logic - of the FPGA through the Internal Configuration Access Port - (ICAP). The ICAP enables partial reconfiguration of the FPGA, - readback of the configuration information, and some control over - 'warm boots' of the FPGA fabric. - - Required properties: - - xlnx,family : The family of the FPGA, necessary since the - capabilities of the underlying ICAP hardware - differ between different families. May be - 'virtex2p', 'virtex4', or 'virtex5'. - - vi) Xilinx Uart 16550 - - Xilinx UART 16550 devices are very similar to the NS16550 but with - different register spacing and an offset from the base address. - - Required properties: - - clock-frequency : Frequency of the clock input - - reg-offset : A value of 3 is required - - reg-shift : A value of 2 is required - - e) USB EHCI controllers - - Required properties: - - compatible : should be "usb-ehci". - - reg : should contain at least address and length of the standard EHCI - register set for the device. Optional platform-dependent registers - (debug-port or other) can be also specified here, but only after - definition of standard EHCI registers. - - interrupts : one EHCI interrupt should be described here. - If device registers are implemented in big endian mode, the device - node should have "big-endian-regs" property. - If controller implementation operates with big endian descriptors, - "big-endian-desc" property should be specified. - If both big endian registers and descriptors are used by the controller - implementation, "big-endian" property can be specified instead of having - both "big-endian-regs" and "big-endian-desc". - - Example (Sequoia 440EPx): - ehci@e0000300 { - compatible = "ibm,usb-ehci-440epx", "usb-ehci"; - interrupt-parent = <&UIC0>; - interrupts = <1a 4>; - reg = <0 e0000300 90 0 e0000390 70>; - big-endian; - }; - - f) MDIO on GPIOs - - Currently defined compatibles: - - virtual,gpio-mdio - - MDC and MDIO lines connected to GPIO controllers are listed in the - gpios property as described in section VIII.1 in the following order: - - MDC, MDIO. - - Example: - - mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qe_pio_a 11 - &qe_pio_c 6>; - }; - - g) SPI (Serial Peripheral Interface) busses - - SPI busses can be described with a node for the SPI master device - and a set of child nodes for each SPI slave on the bus. For this - discussion, it is assumed that the system's SPI controller is in - SPI master mode. This binding does not describe SPI controllers - in slave mode. - - The SPI master node requires the following properties: - - #address-cells - number of cells required to define a chip select - address on the SPI bus. - - #size-cells - should be zero. - - compatible - name of SPI bus controller following generic names - recommended practice. - No other properties are required in the SPI bus node. It is assumed - that a driver for an SPI bus device will understand that it is an SPI bus. - However, the binding does not attempt to define the specific method for - assigning chip select numbers. Since SPI chip select configuration is - flexible and non-standardized, it is left out of this binding with the - assumption that board specific platform code will be used to manage - chip selects. Individual drivers can define additional properties to - support describing the chip select layout. - - SPI slave nodes must be children of the SPI master node and can - contain the following properties. - - reg - (required) chip select address of device. - - compatible - (required) name of SPI device following generic names - recommended practice - - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz - - spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode - - spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode - - spi-cs-high - (optional) Empty property indicating device requires - chip select active high - - SPI example for an MPC5200 SPI bus: - spi@f00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - interrupt-parent = <&mpc5200_pic>; - - ethernet-switch@0 { - compatible = "micrel,ks8995m"; - spi-max-frequency = <1000000>; - reg = <0>; - }; - - codec@1 { - compatible = "ti,tlv320aic26"; - spi-max-frequency = <100000>; - reg = <1>; - }; - }; - -VII - Marvell Discovery mv64[345]6x System Controller chips -=========================================================== - -The Marvell mv64[345]60 series of system controller chips contain -many of the peripherals needed to implement a complete computer -system. In this section, we define device tree nodes to describe -the system controller chip itself and each of the peripherals -which it contains. Compatible string values for each node are -prefixed with the string "marvell,", for Marvell Technology Group Ltd. - -1) The /system-controller node - - This node is used to represent the system-controller and must be - present when the system uses a system controller chip. The top-level - system-controller node contains information that is global to all - devices within the system controller chip. The node name begins - with "system-controller" followed by the unit address, which is - the base address of the memory-mapped register set for the system - controller chip. - - Required properties: - - - ranges : Describes the translation of system controller addresses - for memory mapped registers. - - clock-frequency: Contains the main clock frequency for the system - controller chip. - - reg : This property defines the address and size of the - memory-mapped registers contained within the system controller - chip. The address specified in the "reg" property should match - the unit address of the system-controller node. - - #address-cells : Address representation for system controller - devices. This field represents the number of cells needed to - represent the address of the memory-mapped registers of devices - within the system controller chip. - - #size-cells : Size representation for for the memory-mapped - registers within the system controller chip. - - #interrupt-cells : Defines the width of cells used to represent - interrupts. - - Optional properties: - - - model : The specific model of the system controller chip. Such - as, "mv64360", "mv64460", or "mv64560". - - compatible : A string identifying the compatibility identifiers - of the system controller chip. - - The system-controller node contains child nodes for each system - controller device that the platform uses. Nodes should not be created - for devices which exist on the system controller chip but are not used - - Example Marvell Discovery mv64360 system-controller node: - - system-controller@f1000000 { /* Marvell Discovery mv64360 */ - #address-cells = <1>; - #size-cells = <1>; - model = "mv64360"; /* Default */ - compatible = "marvell,mv64360"; - clock-frequency = <133333333>; - reg = <0xf1000000 0x10000>; - virtual-reg = <0xf1000000>; - ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ - 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ - 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ - 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ - 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ - - [ child node definitions... ] - } - -2) Child nodes of /system-controller - - a) Marvell Discovery MDIO bus - - The MDIO is a bus to which the PHY devices are connected. For each - device that exists on this bus, a child node should be created. See - the definition of the PHY node below for an example of how to define - a PHY. - - Required properties: - - #address-cells : Should be <1> - - #size-cells : Should be <0> - - device_type : Should be "mdio" - - compatible : Should be "marvell,mv64360-mdio" - - Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - device_type = "mdio"; - compatible = "marvell,mv64360-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - - - b) Marvell Discovery ethernet controller - - The Discover ethernet controller is described with two levels - of nodes. The first level describes an ethernet silicon block - and the second level describes up to 3 ethernet nodes within - that block. The reason for the multiple levels is that the - registers for the node are interleaved within a single set - of registers. The "ethernet-block" level describes the - shared register set, and the "ethernet" nodes describe ethernet - port-specific properties. - - Ethernet block node - - Required properties: - - #address-cells : <1> - - #size-cells : <0> - - compatible : "marvell,mv64360-eth-block" - - reg : Offset and length of the register set for this block - - Example Discovery Ethernet block node: - ethernet-block@2000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "marvell,mv64360-eth-block"; - reg = <0x2000 0x2000>; - ethernet@0 { - ....... - }; - }; - - Ethernet port node - - Required properties: - - device_type : Should be "network". - - compatible : Should be "marvell,mv64360-eth". - - reg : Should be <0>, <1>, or <2>, according to which registers - within the silicon block the device uses. - - interrupts : where a is the interrupt number for the port. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - phy : the phandle for the PHY connected to this ethernet - controller. - - local-mac-address : 6 bytes, MAC address - - Example Discovery Ethernet port node: - ethernet@0 { - device_type = "network"; - compatible = "marvell,mv64360-eth"; - reg = <0>; - interrupts = <32>; - interrupt-parent = <&PIC>; - phy = <&PHY0>; - local-mac-address = [ 00 00 00 00 00 00 ]; - }; - - - - c) Marvell Discovery PHY nodes - - Required properties: - - device_type : Should be "ethernet-phy" - - interrupts : where a is the interrupt number for this phy. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - Example Discovery PHY node: - ethernet-phy@1 { - device_type = "ethernet-phy"; - compatible = "broadcom,bcm5421"; - interrupts = <76>; /* GPP 12 */ - interrupt-parent = <&PIC>; - reg = <1>; - }; - - - d) Marvell Discovery SDMA nodes - - Represent DMA hardware associated with the MPSC (multiprotocol - serial controllers). - - Required properties: - - compatible : "marvell,mv64360-sdma" - - reg : Offset and length of the register set for this device - - interrupts : where a is the interrupt number for the DMA - device. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SDMA node: - sdma@4000 { - compatible = "marvell,mv64360-sdma"; - reg = <0x4000 0xc18>; - virtual-reg = <0xf1004000>; - interrupts = <36>; - interrupt-parent = <&PIC>; - }; - - - e) Marvell Discovery BRG nodes - - Represent baud rate generator hardware associated with the MPSC - (multiprotocol serial controllers). - - Required properties: - - compatible : "marvell,mv64360-brg" - - reg : Offset and length of the register set for this device - - clock-src : A value from 0 to 15 which selects the clock - source for the baud rate generator. This value corresponds - to the CLKS value in the BRGx configuration register. See - the mv64x60 User's Manual. - - clock-frequence : The frequency (in Hz) of the baud rate - generator's input clock. - - current-speed : The current speed setting (presumably by - firmware) of the baud rate generator. - - Example Discovery BRG node: - brg@b200 { - compatible = "marvell,mv64360-brg"; - reg = <0xb200 0x8>; - clock-src = <8>; - clock-frequency = <133333333>; - current-speed = <9600>; - }; - - - f) Marvell Discovery CUNIT nodes - - Represent the Serial Communications Unit device hardware. - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - cunit@f200 { - reg = <0xf200 0x200>; - }; - - - g) Marvell Discovery MPSCROUTING nodes - - Represent the Discovery's MPSC routing hardware - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - mpscrouting@b500 { - reg = <0xb400 0xc>; - }; - - - h) Marvell Discovery MPSCINTR nodes - - Represent the Discovery's MPSC DMA interrupt hardware registers - (SDMA cause and mask registers). - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery MPSCINTR node: - mpsintr@b800 { - reg = <0xb800 0x100>; - }; - - - i) Marvell Discovery MPSC nodes - - Represent the Discovery's MPSC (Multiprotocol Serial Controller) - serial port. - - Required properties: - - device_type : "serial" - - compatible : "marvell,mv64360-mpsc" - - reg : Offset and length of the register set for this device - - sdma : the phandle for the SDMA node used by this port - - brg : the phandle for the BRG node used by this port - - cunit : the phandle for the CUNIT node used by this port - - mpscrouting : the phandle for the MPSCROUTING node used by this port - - mpscintr : the phandle for the MPSCINTR node used by this port - - cell-index : the hardware index of this cell in the MPSC core - - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) - register - - interrupts : where a is the interrupt number for the MPSC. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery MPSCINTR node: - mpsc@8000 { - device_type = "serial"; - compatible = "marvell,mv64360-mpsc"; - reg = <0x8000 0x38>; - virtual-reg = <0xf1008000>; - sdma = <&SDMA0>; - brg = <&BRG0>; - cunit = <&CUNIT>; - mpscrouting = <&MPSCROUTING>; - mpscintr = <&MPSCINTR>; - cell-index = <0>; - max_idle = <40>; - interrupts = <40>; - interrupt-parent = <&PIC>; - }; - - - j) Marvell Discovery Watch Dog Timer nodes - - Represent the Discovery's watchdog timer hardware - - Required properties: - - compatible : "marvell,mv64360-wdt" - - reg : Offset and length of the register set for this device - - Example Discovery Watch Dog Timer node: - wdt@b410 { - compatible = "marvell,mv64360-wdt"; - reg = <0xb410 0x8>; - }; - - - k) Marvell Discovery I2C nodes - - Represent the Discovery's I2C hardware - - Required properties: - - device_type : "i2c" - - compatible : "marvell,mv64360-i2c" - - reg : Offset and length of the register set for this device - - interrupts : where a is the interrupt number for the I2C. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery I2C node: - compatible = "marvell,mv64360-i2c"; - reg = <0xc000 0x20>; - virtual-reg = <0xf100c000>; - interrupts = <37>; - interrupt-parent = <&PIC>; - }; - - - l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes - - Represent the Discovery's PIC hardware - - Required properties: - - #interrupt-cells : <1> - - #address-cells : <0> - - compatible : "marvell,mv64360-pic" - - reg : Offset and length of the register set for this device - - interrupt-controller - - Example Discovery PIC node: - pic { - #interrupt-cells = <1>; - #address-cells = <0>; - compatible = "marvell,mv64360-pic"; - reg = <0x0 0x88>; - interrupt-controller; - }; - - - m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes - - Represent the Discovery's MPP hardware - - Required properties: - - compatible : "marvell,mv64360-mpp" - - reg : Offset and length of the register set for this device - - Example Discovery MPP node: - mpp@f000 { - compatible = "marvell,mv64360-mpp"; - reg = <0xf000 0x10>; - }; - - - n) Marvell Discovery GPP (General Purpose Pins) nodes - - Represent the Discovery's GPP hardware - - Required properties: - - compatible : "marvell,mv64360-gpp" - - reg : Offset and length of the register set for this device - - Example Discovery GPP node: - gpp@f000 { - compatible = "marvell,mv64360-gpp"; - reg = <0xf100 0x20>; - }; - - - o) Marvell Discovery PCI host bridge node - - Represents the Discovery's PCI host bridge device. The properties - for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE - 1275-1994. A typical value for the compatible property is - "marvell,mv64360-pci". - - Example Discovery PCI host bridge node - pci@80000000 { - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - device_type = "pci"; - compatible = "marvell,mv64360-pci"; - reg = <0xcf8 0x8>; - ranges = <0x01000000 0x0 0x0 - 0x88000000 0x0 0x01000000 - 0x02000000 0x0 0x80000000 - 0x80000000 0x0 0x08000000>; - bus-range = <0 255>; - clock-frequency = <66000000>; - interrupt-parent = <&PIC>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0a */ - 0x5000 0 0 1 &PIC 80 - 0x5000 0 0 2 &PIC 81 - 0x5000 0 0 3 &PIC 91 - 0x5000 0 0 4 &PIC 93 - - /* IDSEL 0x0b */ - 0x5800 0 0 1 &PIC 91 - 0x5800 0 0 2 &PIC 93 - 0x5800 0 0 3 &PIC 80 - 0x5800 0 0 4 &PIC 81 - - /* IDSEL 0x0c */ - 0x6000 0 0 1 &PIC 91 - 0x6000 0 0 2 &PIC 93 - 0x6000 0 0 3 &PIC 80 - 0x6000 0 0 4 &PIC 81 - - /* IDSEL 0x0d */ - 0x6800 0 0 1 &PIC 93 - 0x6800 0 0 2 &PIC 80 - 0x6800 0 0 3 &PIC 81 - 0x6800 0 0 4 &PIC 91 - >; - }; - - - p) Marvell Discovery CPU Error nodes - - Represent the Discovery's CPU error handler device. - - Required properties: - - compatible : "marvell,mv64360-cpu-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery CPU Error node: - cpu-error@0070 { - compatible = "marvell,mv64360-cpu-error"; - reg = <0x70 0x10 0x128 0x28>; - interrupts = <3>; - interrupt-parent = <&PIC>; - }; - - - q) Marvell Discovery SRAM Controller nodes - - Represent the Discovery's SRAM controller device. - - Required properties: - - compatible : "marvell,mv64360-sram-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SRAM Controller node: - sram-ctrl@0380 { - compatible = "marvell,mv64360-sram-ctrl"; - reg = <0x380 0x80>; - interrupts = <13>; - interrupt-parent = <&PIC>; - }; - - - r) Marvell Discovery PCI Error Handler nodes - - Represent the Discovery's PCI error handler device. - - Required properties: - - compatible : "marvell,mv64360-pci-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery PCI Error Handler node: - pci-error@1d40 { - compatible = "marvell,mv64360-pci-error"; - reg = <0x1d40 0x40 0xc28 0x4>; - interrupts = <12>; - interrupt-parent = <&PIC>; - }; - - - s) Marvell Discovery Memory Controller nodes - - Represent the Discovery's memory controller device. - - Required properties: - - compatible : "marvell,mv64360-mem-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery Memory Controller node: - mem-ctrl@1400 { - compatible = "marvell,mv64360-mem-ctrl"; - reg = <0x1400 0x60>; - interrupts = <17>; - interrupt-parent = <&PIC>; - }; - - -VIII - Specifying interrupt information for devices +VII - Specifying interrupt information for devices =================================================== The device tree represents the busses and devices of a hardware @@ -2439,56 +1324,7 @@ encodings listed below: 2 = high to low edge sensitive type enabled 3 = low to high edge sensitive type enabled -IX - Specifying GPIO information for devices -============================================ - -1) gpios property ------------------ - -Nodes that makes use of GPIOs should define them using `gpios' property, -format of which is: <&gpio-controller1-phandle gpio1-specifier - &gpio-controller2-phandle gpio2-specifier - 0 /* holes are permitted, means no GPIO 3 */ - &gpio-controller4-phandle gpio4-specifier - ...>; - -Note that gpio-specifier length is controller dependent. - -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. - -Example of the node using GPIOs: - - node { - gpios = <&qe_pio_e 18 0>; - }; - -In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. - -2) gpio-controller nodes ------------------------- - -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -Example of two SOC GPIO banks defined as gpio-controller nodes: - - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; - -X - Specifying Device Power Management Information (sleep property) +VIII - Specifying Device Power Management Information (sleep property) =================================================================== Devices on SOCs often have mechanisms for placing devices into low-power diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt new file mode 100644 index 000000000000..2161334a7ca5 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : + - interrupt-parent : optional, if needed for interrupt mapping + - reg : + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : . + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + diff --git a/Documentation/powerpc/dts-bindings/gpio/gpio.txt b/Documentation/powerpc/dts-bindings/gpio/gpio.txt new file mode 100644 index 000000000000..edaa84d288a1 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/gpio/gpio.txt @@ -0,0 +1,50 @@ +Specifying GPIO information for devices +============================================ + +1) gpios property +----------------- + +Nodes that makes use of GPIOs should define them using `gpios' property, +format of which is: <&gpio-controller1-phandle gpio1-specifier + &gpio-controller2-phandle gpio2-specifier + 0 /* holes are permitted, means no GPIO 3 */ + &gpio-controller4-phandle gpio4-specifier + ...>; + +Note that gpio-specifier length is controller dependent. + +gpio-specifier may encode: bank, pin position inside the bank, +whether pin is open-drain and whether pin is logically inverted. + +Example of the node using GPIOs: + + node { + gpios = <&qe_pio_e 18 0>; + }; + +In this example gpio-specifier is "18 0" and encodes GPIO pin number, +and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; + + diff --git a/Documentation/powerpc/dts-bindings/gpio/mdio.txt b/Documentation/powerpc/dts-bindings/gpio/mdio.txt new file mode 100644 index 000000000000..bc9549529014 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/gpio/mdio.txt @@ -0,0 +1,19 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Example: + +mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/powerpc/dts-bindings/marvell.txt b/Documentation/powerpc/dts-bindings/marvell.txt new file mode 100644 index 000000000000..3708a2fd4747 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/marvell.txt @@ -0,0 +1,521 @@ +Marvell Discovery mv64[345]6x System Controller chips +=========================================================== + +The Marvell mv64[345]60 series of system controller chips contain +many of the peripherals needed to implement a complete computer +system. In this section, we define device tree nodes to describe +the system controller chip itself and each of the peripherals +which it contains. Compatible string values for each node are +prefixed with the string "marvell,", for Marvell Technology Group Ltd. + +1) The /system-controller node + + This node is used to represent the system-controller and must be + present when the system uses a system controller chip. The top-level + system-controller node contains information that is global to all + devices within the system controller chip. The node name begins + with "system-controller" followed by the unit address, which is + the base address of the memory-mapped register set for the system + controller chip. + + Required properties: + + - ranges : Describes the translation of system controller addresses + for memory mapped registers. + - clock-frequency: Contains the main clock frequency for the system + controller chip. + - reg : This property defines the address and size of the + memory-mapped registers contained within the system controller + chip. The address specified in the "reg" property should match + the unit address of the system-controller node. + - #address-cells : Address representation for system controller + devices. This field represents the number of cells needed to + represent the address of the memory-mapped registers of devices + within the system controller chip. + - #size-cells : Size representation for for the memory-mapped + registers within the system controller chip. + - #interrupt-cells : Defines the width of cells used to represent + interrupts. + + Optional properties: + + - model : The specific model of the system controller chip. Such + as, "mv64360", "mv64460", or "mv64560". + - compatible : A string identifying the compatibility identifiers + of the system controller chip. + + The system-controller node contains child nodes for each system + controller device that the platform uses. Nodes should not be created + for devices which exist on the system controller chip but are not used + + Example Marvell Discovery mv64360 system-controller node: + + system-controller@f1000000 { /* Marvell Discovery mv64360 */ + #address-cells = <1>; + #size-cells = <1>; + model = "mv64360"; /* Default */ + compatible = "marvell,mv64360"; + clock-frequency = <133333333>; + reg = <0xf1000000 0x10000>; + virtual-reg = <0xf1000000>; + ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ + 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ + 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ + 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ + 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ + + [ child node definitions... ] + } + +2) Child nodes of /system-controller + + a) Marvell Discovery MDIO bus + + The MDIO is a bus to which the PHY devices are connected. For each + device that exists on this bus, a child node should be created. See + the definition of the PHY node below for an example of how to define + a PHY. + + Required properties: + - #address-cells : Should be <1> + - #size-cells : Should be <0> + - device_type : Should be "mdio" + - compatible : Should be "marvell,mv64360-mdio" + + Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + device_type = "mdio"; + compatible = "marvell,mv64360-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + + + b) Marvell Discovery ethernet controller + + The Discover ethernet controller is described with two levels + of nodes. The first level describes an ethernet silicon block + and the second level describes up to 3 ethernet nodes within + that block. The reason for the multiple levels is that the + registers for the node are interleaved within a single set + of registers. The "ethernet-block" level describes the + shared register set, and the "ethernet" nodes describe ethernet + port-specific properties. + + Ethernet block node + + Required properties: + - #address-cells : <1> + - #size-cells : <0> + - compatible : "marvell,mv64360-eth-block" + - reg : Offset and length of the register set for this block + + Example Discovery Ethernet block node: + ethernet-block@2000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,mv64360-eth-block"; + reg = <0x2000 0x2000>; + ethernet@0 { + ....... + }; + }; + + Ethernet port node + + Required properties: + - device_type : Should be "network". + - compatible : Should be "marvell,mv64360-eth". + - reg : Should be <0>, <1>, or <2>, according to which registers + within the silicon block the device uses. + - interrupts : where a is the interrupt number for the port. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + - phy : the phandle for the PHY connected to this ethernet + controller. + - local-mac-address : 6 bytes, MAC address + + Example Discovery Ethernet port node: + ethernet@0 { + device_type = "network"; + compatible = "marvell,mv64360-eth"; + reg = <0>; + interrupts = <32>; + interrupt-parent = <&PIC>; + phy = <&PHY0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + + + c) Marvell Discovery PHY nodes + + Required properties: + - device_type : Should be "ethernet-phy" + - interrupts : where a is the interrupt number for this phy. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + + Example Discovery PHY node: + ethernet-phy@1 { + device_type = "ethernet-phy"; + compatible = "broadcom,bcm5421"; + interrupts = <76>; /* GPP 12 */ + interrupt-parent = <&PIC>; + reg = <1>; + }; + + + d) Marvell Discovery SDMA nodes + + Represent DMA hardware associated with the MPSC (multiprotocol + serial controllers). + + Required properties: + - compatible : "marvell,mv64360-sdma" + - reg : Offset and length of the register set for this device + - interrupts : where a is the interrupt number for the DMA + device. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SDMA node: + sdma@4000 { + compatible = "marvell,mv64360-sdma"; + reg = <0x4000 0xc18>; + virtual-reg = <0xf1004000>; + interrupts = <36>; + interrupt-parent = <&PIC>; + }; + + + e) Marvell Discovery BRG nodes + + Represent baud rate generator hardware associated with the MPSC + (multiprotocol serial controllers). + + Required properties: + - compatible : "marvell,mv64360-brg" + - reg : Offset and length of the register set for this device + - clock-src : A value from 0 to 15 which selects the clock + source for the baud rate generator. This value corresponds + to the CLKS value in the BRGx configuration register. See + the mv64x60 User's Manual. + - clock-frequence : The frequency (in Hz) of the baud rate + generator's input clock. + - current-speed : The current speed setting (presumably by + firmware) of the baud rate generator. + + Example Discovery BRG node: + brg@b200 { + compatible = "marvell,mv64360-brg"; + reg = <0xb200 0x8>; + clock-src = <8>; + clock-frequency = <133333333>; + current-speed = <9600>; + }; + + + f) Marvell Discovery CUNIT nodes + + Represent the Serial Communications Unit device hardware. + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + cunit@f200 { + reg = <0xf200 0x200>; + }; + + + g) Marvell Discovery MPSCROUTING nodes + + Represent the Discovery's MPSC routing hardware + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + mpscrouting@b500 { + reg = <0xb400 0xc>; + }; + + + h) Marvell Discovery MPSCINTR nodes + + Represent the Discovery's MPSC DMA interrupt hardware registers + (SDMA cause and mask registers). + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery MPSCINTR node: + mpsintr@b800 { + reg = <0xb800 0x100>; + }; + + + i) Marvell Discovery MPSC nodes + + Represent the Discovery's MPSC (Multiprotocol Serial Controller) + serial port. + + Required properties: + - device_type : "serial" + - compatible : "marvell,mv64360-mpsc" + - reg : Offset and length of the register set for this device + - sdma : the phandle for the SDMA node used by this port + - brg : the phandle for the BRG node used by this port + - cunit : the phandle for the CUNIT node used by this port + - mpscrouting : the phandle for the MPSCROUTING node used by this port + - mpscintr : the phandle for the MPSCINTR node used by this port + - cell-index : the hardware index of this cell in the MPSC core + - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) + register + - interrupts : where a is the interrupt number for the MPSC. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery MPSCINTR node: + mpsc@8000 { + device_type = "serial"; + compatible = "marvell,mv64360-mpsc"; + reg = <0x8000 0x38>; + virtual-reg = <0xf1008000>; + sdma = <&SDMA0>; + brg = <&BRG0>; + cunit = <&CUNIT>; + mpscrouting = <&MPSCROUTING>; + mpscintr = <&MPSCINTR>; + cell-index = <0>; + max_idle = <40>; + interrupts = <40>; + interrupt-parent = <&PIC>; + }; + + + j) Marvell Discovery Watch Dog Timer nodes + + Represent the Discovery's watchdog timer hardware + + Required properties: + - compatible : "marvell,mv64360-wdt" + - reg : Offset and length of the register set for this device + + Example Discovery Watch Dog Timer node: + wdt@b410 { + compatible = "marvell,mv64360-wdt"; + reg = <0xb410 0x8>; + }; + + + k) Marvell Discovery I2C nodes + + Represent the Discovery's I2C hardware + + Required properties: + - device_type : "i2c" + - compatible : "marvell,mv64360-i2c" + - reg : Offset and length of the register set for this device + - interrupts : where a is the interrupt number for the I2C. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery I2C node: + compatible = "marvell,mv64360-i2c"; + reg = <0xc000 0x20>; + virtual-reg = <0xf100c000>; + interrupts = <37>; + interrupt-parent = <&PIC>; + }; + + + l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes + + Represent the Discovery's PIC hardware + + Required properties: + - #interrupt-cells : <1> + - #address-cells : <0> + - compatible : "marvell,mv64360-pic" + - reg : Offset and length of the register set for this device + - interrupt-controller + + Example Discovery PIC node: + pic { + #interrupt-cells = <1>; + #address-cells = <0>; + compatible = "marvell,mv64360-pic"; + reg = <0x0 0x88>; + interrupt-controller; + }; + + + m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes + + Represent the Discovery's MPP hardware + + Required properties: + - compatible : "marvell,mv64360-mpp" + - reg : Offset and length of the register set for this device + + Example Discovery MPP node: + mpp@f000 { + compatible = "marvell,mv64360-mpp"; + reg = <0xf000 0x10>; + }; + + + n) Marvell Discovery GPP (General Purpose Pins) nodes + + Represent the Discovery's GPP hardware + + Required properties: + - compatible : "marvell,mv64360-gpp" + - reg : Offset and length of the register set for this device + + Example Discovery GPP node: + gpp@f000 { + compatible = "marvell,mv64360-gpp"; + reg = <0xf100 0x20>; + }; + + + o) Marvell Discovery PCI host bridge node + + Represents the Discovery's PCI host bridge device. The properties + for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE + 1275-1994. A typical value for the compatible property is + "marvell,mv64360-pci". + + Example Discovery PCI host bridge node + pci@80000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "marvell,mv64360-pci"; + reg = <0xcf8 0x8>; + ranges = <0x01000000 0x0 0x0 + 0x88000000 0x0 0x01000000 + 0x02000000 0x0 0x80000000 + 0x80000000 0x0 0x08000000>; + bus-range = <0 255>; + clock-frequency = <66000000>; + interrupt-parent = <&PIC>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0a */ + 0x5000 0 0 1 &PIC 80 + 0x5000 0 0 2 &PIC 81 + 0x5000 0 0 3 &PIC 91 + 0x5000 0 0 4 &PIC 93 + + /* IDSEL 0x0b */ + 0x5800 0 0 1 &PIC 91 + 0x5800 0 0 2 &PIC 93 + 0x5800 0 0 3 &PIC 80 + 0x5800 0 0 4 &PIC 81 + + /* IDSEL 0x0c */ + 0x6000 0 0 1 &PIC 91 + 0x6000 0 0 2 &PIC 93 + 0x6000 0 0 3 &PIC 80 + 0x6000 0 0 4 &PIC 81 + + /* IDSEL 0x0d */ + 0x6800 0 0 1 &PIC 93 + 0x6800 0 0 2 &PIC 80 + 0x6800 0 0 3 &PIC 81 + 0x6800 0 0 4 &PIC 91 + >; + }; + + + p) Marvell Discovery CPU Error nodes + + Represent the Discovery's CPU error handler device. + + Required properties: + - compatible : "marvell,mv64360-cpu-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery CPU Error node: + cpu-error@0070 { + compatible = "marvell,mv64360-cpu-error"; + reg = <0x70 0x10 0x128 0x28>; + interrupts = <3>; + interrupt-parent = <&PIC>; + }; + + + q) Marvell Discovery SRAM Controller nodes + + Represent the Discovery's SRAM controller device. + + Required properties: + - compatible : "marvell,mv64360-sram-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SRAM Controller node: + sram-ctrl@0380 { + compatible = "marvell,mv64360-sram-ctrl"; + reg = <0x380 0x80>; + interrupts = <13>; + interrupt-parent = <&PIC>; + }; + + + r) Marvell Discovery PCI Error Handler nodes + + Represent the Discovery's PCI error handler device. + + Required properties: + - compatible : "marvell,mv64360-pci-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery PCI Error Handler node: + pci-error@1d40 { + compatible = "marvell,mv64360-pci-error"; + reg = <0x1d40 0x40 0xc28 0x4>; + interrupts = <12>; + interrupt-parent = <&PIC>; + }; + + + s) Marvell Discovery Memory Controller nodes + + Represent the Discovery's memory controller device. + + Required properties: + - compatible : "marvell,mv64360-mem-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery Memory Controller node: + mem-ctrl@1400 { + compatible = "marvell,mv64360-mem-ctrl"; + reg = <0x1400 0x60>; + interrupts = <17>; + interrupt-parent = <&PIC>; + }; + + diff --git a/Documentation/powerpc/dts-bindings/phy.txt b/Documentation/powerpc/dts-bindings/phy.txt new file mode 100644 index 000000000000..bb8c742eb8c5 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/phy.txt @@ -0,0 +1,25 @@ +PHY nodes + +Required properties: + + - device_type : Should be "ethernet-phy" + - interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + - linux,phandle : phandle for this node; likely referenced by an + ethernet controller node. + +Example: + +ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; +}; diff --git a/Documentation/powerpc/dts-bindings/spi-bus.txt b/Documentation/powerpc/dts-bindings/spi-bus.txt new file mode 100644 index 000000000000..e782add2e457 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/spi-bus.txt @@ -0,0 +1,57 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/usb-ehci.txt b/Documentation/powerpc/dts-bindings/usb-ehci.txt new file mode 100644 index 000000000000..fa18612f757b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/usb-ehci.txt @@ -0,0 +1,25 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "usb-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. +If device registers are implemented in big endian mode, the device +node should have "big-endian-regs" property. +If controller implementation operates with big endian descriptors, +"big-endian-desc" property should be specified. +If both big endian registers and descriptors are used by the controller +implementation, "big-endian" property can be specified instead of having +both "big-endian-regs" and "big-endian-desc". + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt new file mode 100644 index 000000000000..80339fe4300b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/xilinx.txt @@ -0,0 +1,295 @@ + d) Xilinx IP cores + + The Xilinx EDK toolchain ships with a set of IP cores (devices) for use + in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range + of standard device types (network, serial, etc.) and miscellaneous + devices (gpio, LCD, spi, etc). Also, since these devices are + implemented within the fpga fabric every instance of the device can be + synthesised with different options that change the behaviour. + + Each IP-core has a set of parameters which the FPGA designer can use to + control how the core is synthesized. Historically, the EDK tool would + extract the device parameters relevant to device drivers and copy them + into an 'xparameters.h' in the form of #define symbols. This tells the + device drivers how the IP cores are configured, but it requres the kernel + to be recompiled every time the FPGA bitstream is resynthesized. + + The new approach is to export the parameters into the device tree and + generate a new device tree each time the FPGA bitstream changes. The + parameters which used to be exported as #defines will now become + properties of the device node. In general, device nodes for IP-cores + will take the following form: + + (name): (generic-name)@(base-address) { + compatible = "xlnx,(ip-core-name)-(HW_VER)" + [, (list of compatible devices), ...]; + reg = <(baseaddr) (size)>; + interrupt-parent = <&interrupt-controller-phandle>; + interrupts = < ... >; + xlnx,(parameter1) = "(string-value)"; + xlnx,(parameter2) = <(int-value)>; + }; + + (generic-name): an open firmware-style name that describes the + generic class of device. Preferably, this is one word, such + as 'serial' or 'ethernet'. + (ip-core-name): the name of the ip block (given after the BEGIN + directive in system.mhs). Should be in lowercase + and all underscores '_' converted to dashes '-'. + (name): is derived from the "PARAMETER INSTANCE" value. + (parameter#): C_* parameters from system.mhs. The C_ prefix is + dropped from the parameter name, the name is converted + to lowercase and all underscore '_' characters are + converted to dashes '-'. + (baseaddr): the baseaddr parameter value (often named C_BASEADDR). + (HW_VER): from the HW_VER parameter. + (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). + + Typically, the compatible list will include the exact IP core version + followed by an older IP core version which implements the same + interface or any other device with the same interface. + + 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. + + For example, the following block from system.mhs: + + BEGIN opb_uartlite + PARAMETER INSTANCE = opb_uartlite_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BAUDRATE = 115200 + PARAMETER C_DATA_BITS = 8 + PARAMETER C_ODD_PARITY = 0 + PARAMETER C_USE_PARITY = 0 + PARAMETER C_CLK_FREQ = 50000000 + PARAMETER C_BASEADDR = 0xEC100000 + PARAMETER C_HIGHADDR = 0xEC10FFFF + BUS_INTERFACE SOPB = opb_7 + PORT OPB_Clk = CLK_50MHz + PORT Interrupt = opb_uartlite_0_Interrupt + PORT RX = opb_uartlite_0_RX + PORT TX = opb_uartlite_0_TX + PORT OPB_Rst = sys_bus_reset_0 + END + + becomes the following device tree node: + + opb_uartlite_0: serial@ec100000 { + device_type = "serial"; + compatible = "xlnx,opb-uartlite-1.00.b"; + reg = ; + interrupt-parent = <&opb_intc_0>; + interrupts = <1 0>; // got this from the opb_intc parameters + current-speed = ; // standard serial device prop + clock-frequency = ; // standard serial device prop + xlnx,data-bits = <8>; + xlnx,odd-parity = <0>; + xlnx,use-parity = <0>; + }; + + Some IP cores actually implement 2 or more logical devices. In + this case, the device should still describe the whole IP core with + a single node and add a child node for each logical device. The + ranges property can be used to translate from parent IP-core to the + registers of each device. In addition, the parent node should be + compatible with the bus type 'xlnx,compound', and should contain + #address-cells and #size-cells, as with any other bus. (Note: this + makes the assumption that both logical devices have the same bus + binding. If this is not true, then separate nodes should be used + for each logical device). The 'cell-index' property can be used to + enumerate logical devices within an IP core. For example, the + following is the system.mhs entry for the dual ps2 controller found + on the ml403 reference design. + + BEGIN opb_ps2_dual_ref + PARAMETER INSTANCE = opb_ps2_dual_ref_0 + PARAMETER HW_VER = 1.00.a + PARAMETER C_BASEADDR = 0xA9000000 + PARAMETER C_HIGHADDR = 0xA9001FFF + BUS_INTERFACE SOPB = opb_v20_0 + PORT Sys_Intr1 = ps2_1_intr + PORT Sys_Intr2 = ps2_2_intr + PORT Clkin1 = ps2_clk_rx_1 + PORT Clkin2 = ps2_clk_rx_2 + PORT Clkpd1 = ps2_clk_tx_1 + PORT Clkpd2 = ps2_clk_tx_2 + PORT Rx1 = ps2_d_rx_1 + PORT Rx2 = ps2_d_rx_2 + PORT Txpd1 = ps2_d_tx_1 + PORT Txpd2 = ps2_d_tx_2 + END + + It would result in the following device tree nodes: + + opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,compound"; + ranges = <0 a9000000 2000>; + // If this device had extra parameters, then they would + // go here. + ps2@0 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <0 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + ps2@1000 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <1000 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + }; + + Also, the system.mhs file defines bus attachments from the processor + to the devices. The device tree structure should reflect the bus + attachments. Again an example; this system.mhs fragment: + + BEGIN ppc405_virtex4 + PARAMETER INSTANCE = ppc405_0 + PARAMETER HW_VER = 1.01.a + BUS_INTERFACE DPLB = plb_v34_0 + BUS_INTERFACE IPLB = plb_v34_0 + END + + BEGIN opb_intc + PARAMETER INSTANCE = opb_intc_0 + PARAMETER HW_VER = 1.00.c + PARAMETER C_BASEADDR = 0xD1000FC0 + PARAMETER C_HIGHADDR = 0xD1000FDF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN opb_uart16550 + PARAMETER INSTANCE = opb_uart16550_0 + PARAMETER HW_VER = 1.00.d + PARAMETER C_BASEADDR = 0xa0000000 + PARAMETER C_HIGHADDR = 0xa0001FFF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN plb_v34 + PARAMETER INSTANCE = plb_v34_0 + PARAMETER HW_VER = 1.02.a + END + + BEGIN plb_bram_if_cntlr + PARAMETER INSTANCE = plb_bram_if_cntlr_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BASEADDR = 0xFFFF0000 + PARAMETER C_HIGHADDR = 0xFFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + END + + BEGIN plb2opb_bridge + PARAMETER INSTANCE = plb2opb_bridge_0 + PARAMETER HW_VER = 1.01.a + PARAMETER C_RNG0_BASEADDR = 0x20000000 + PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF + PARAMETER C_RNG1_BASEADDR = 0x60000000 + PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF + PARAMETER C_RNG2_BASEADDR = 0x80000000 + PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF + PARAMETER C_RNG3_BASEADDR = 0xC0000000 + PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + BUS_INTERFACE MOPB = opb_v20_0 + END + + Gives this device tree (some properties removed for clarity): + + plb@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,plb-v34-1.02.a"; + device_type = "ibm,plb"; + ranges; // 1:1 translation + + plb_bram_if_cntrl_0: bram@ffff0000 { + reg = ; + } + + opb@20000000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <20000000 20000000 20000000 + 60000000 60000000 20000000 + 80000000 80000000 40000000 + c0000000 c0000000 20000000>; + + opb_uart16550_0: serial@a0000000 { + reg = ; + }; + + opb_intc_0: interrupt-controller@d1000fc0 { + reg = ; + }; + }; + }; + + That covers the general approach to binding xilinx IP cores into the + device tree. The following are bindings for specific devices: + + i) Xilinx ML300 Framebuffer + + Simple framebuffer device from the ML300 reference design (also on the + ML403 reference design as well as others). + + Optional properties: + - resolution = : pixel resolution of framebuffer. Some + implementations use a different resolution. + Default is + - virt-resolution = : Size of framebuffer in memory. + Default is . + - rotate-display (empty) : rotate display 180 degrees. + + ii) Xilinx SystemACE + + The Xilinx SystemACE device is used to program FPGAs from an FPGA + bitstream stored on a CF card. It can also be used as a generic CF + interface device. + + Optional properties: + - 8-bit (empty) : Set this property for SystemACE in 8 bit mode + + iii) Xilinx EMAC and Xilinx TEMAC + + Xilinx Ethernet devices. In addition to general xilinx properties + listed above, nodes for these devices should include a phy-handle + property, and may include other common network device properties + like local-mac-address. + + iv) Xilinx Uartlite + + Xilinx uartlite devices are simple fixed speed serial ports. + + Required properties: + - current-speed : Baud rate of uartlite + + v) Xilinx hwicap + + Xilinx hwicap devices provide access to the configuration logic + of the FPGA through the Internal Configuration Access Port + (ICAP). The ICAP enables partial reconfiguration of the FPGA, + readback of the configuration information, and some control over + 'warm boots' of the FPGA fabric. + + Required properties: + - xlnx,family : The family of the FPGA, necessary since the + capabilities of the underlying ICAP hardware + differ between different families. May be + 'virtex2p', 'virtex4', or 'virtex5'. + + vi) Xilinx Uart 16550 + + Xilinx UART 16550 devices are very similar to the NS16550 but with + different register spacing and an offset from the base address. + + Required properties: + - clock-frequency : Frequency of the clock input + - reg-offset : A value of 3 is required + - reg-shift : A value of 2 is required + + diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index bf6cedfa05db..d00131ca0835 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -62,7 +62,6 @@ config HAVE_LATENCYTOP_SUPPORT config TRACE_IRQFLAGS_SUPPORT bool - depends on PPC64 default y config LOCKDEP_SUPPORT diff --git a/arch/powerpc/boot/.gitignore b/arch/powerpc/boot/.gitignore index 2f50acd11a60..3d80c3e9cf60 100644 --- a/arch/powerpc/boot/.gitignore +++ b/arch/powerpc/boot/.gitignore @@ -36,3 +36,13 @@ zImage.pseries zconf.h zlib.h zutil.h +fdt.c +fdt.h +fdt_ro.c +fdt_rw.c +fdt_strerror.c +fdt_sw.c +fdt_wip.c +libfdt.h +libfdt_internal.h + diff --git a/arch/powerpc/boot/dts/amigaone.dts b/arch/powerpc/boot/dts/amigaone.dts index 26549fca2ed4..49ac36b16dd7 100644 --- a/arch/powerpc/boot/dts/amigaone.dts +++ b/arch/powerpc/boot/dts/amigaone.dts @@ -70,8 +70,8 @@ devsel-speed = <0x00000001>; min-grant = <0>; max-latency = <0>; - /* First 64k for I/O at 0x0 on PCI mapped to 0x0 on ISA. */ - ranges = <0x00000001 0 0x01000000 0 0x00000000 0x00010000>; + /* First 4k for I/O at 0x0 on PCI mapped to 0x0 on ISA. */ + ranges = <0x00000001 0 0x01000000 0 0x00000000 0x00001000>; interrupt-parent = <&i8259>; #interrupt-cells = <2>; #address-cells = <2>; diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts index a8dcb018c4a5..a680165292f2 100644 --- a/arch/powerpc/boot/dts/mpc8569mds.dts +++ b/arch/powerpc/boot/dts/mpc8569mds.dts @@ -253,6 +253,7 @@ /* Filled in by U-Boot */ clock-frequency = <0>; status = "disabled"; + sdhci,1-bit-only; }; crypto@30000 { diff --git a/arch/powerpc/include/asm/cpm1.h b/arch/powerpc/include/asm/cpm1.h index 2ff798744c1d..7685ffde8821 100644 --- a/arch/powerpc/include/asm/cpm1.h +++ b/arch/powerpc/include/asm/cpm1.h @@ -598,8 +598,6 @@ typedef struct risc_timer_pram { #define CICR_IEN ((uint)0x00000080) /* Int. enable */ #define CICR_SPS ((uint)0x00000001) /* SCC Spread */ -#define IMAP_ADDR (get_immrbase()) - #define CPM_PIN_INPUT 0 #define CPM_PIN_OUTPUT 1 #define CPM_PIN_PRIMARY 0 diff --git a/arch/powerpc/include/asm/dma-mapping.h b/arch/powerpc/include/asm/dma-mapping.h index 3d9e887c3c0c..b44aaabdd1a6 100644 --- a/arch/powerpc/include/asm/dma-mapping.h +++ b/arch/powerpc/include/asm/dma-mapping.h @@ -309,7 +309,9 @@ static inline void dma_sync_single_for_cpu(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_single_range_for_cpu(dev, dma_handle, 0, + + if (dma_ops->sync_single_range_for_cpu) + dma_ops->sync_single_range_for_cpu(dev, dma_handle, 0, size, direction); } @@ -320,7 +322,9 @@ static inline void dma_sync_single_for_device(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_single_range_for_device(dev, dma_handle, + + if (dma_ops->sync_single_range_for_device) + dma_ops->sync_single_range_for_device(dev, dma_handle, 0, size, direction); } @@ -331,7 +335,9 @@ static inline void dma_sync_sg_for_cpu(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_sg_for_cpu(dev, sgl, nents, direction); + + if (dma_ops->sync_sg_for_cpu) + dma_ops->sync_sg_for_cpu(dev, sgl, nents, direction); } static inline void dma_sync_sg_for_device(struct device *dev, @@ -341,7 +347,9 @@ static inline void dma_sync_sg_for_device(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_sg_for_device(dev, sgl, nents, direction); + + if (dma_ops->sync_sg_for_device) + dma_ops->sync_sg_for_device(dev, sgl, nents, direction); } static inline void dma_sync_single_range_for_cpu(struct device *dev, @@ -351,7 +359,9 @@ static inline void dma_sync_single_range_for_cpu(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_single_range_for_cpu(dev, dma_handle, + + if (dma_ops->sync_single_range_for_cpu) + dma_ops->sync_single_range_for_cpu(dev, dma_handle, offset, size, direction); } @@ -362,7 +372,9 @@ static inline void dma_sync_single_range_for_device(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->sync_single_range_for_device(dev, dma_handle, offset, + + if (dma_ops->sync_single_range_for_device) + dma_ops->sync_single_range_for_device(dev, dma_handle, offset, size, direction); } #else /* CONFIG_PPC_NEED_DMA_SYNC_OPS */ diff --git a/arch/powerpc/include/asm/highmem.h b/arch/powerpc/include/asm/highmem.h index 684a73f4324f..a74c4ee6c020 100644 --- a/arch/powerpc/include/asm/highmem.h +++ b/arch/powerpc/include/asm/highmem.h @@ -22,9 +22,7 @@ #ifdef __KERNEL__ -#include #include -#include #include #include #include @@ -62,6 +60,9 @@ extern pte_t *pkmap_page_table; extern void *kmap_high(struct page *page); extern void kunmap_high(struct page *page); +extern void *kmap_atomic_prot(struct page *page, enum km_type type, + pgprot_t prot); +extern void kunmap_atomic(void *kvaddr, enum km_type type); static inline void *kmap(struct page *page) { @@ -79,62 +80,11 @@ static inline void kunmap(struct page *page) kunmap_high(page); } -/* - * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap - * gives a more generic (and caching) interface. But kmap_atomic can - * be used in IRQ contexts, so in some (very limited) cases we need - * it. - */ -static inline void *kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot) -{ - unsigned int idx; - unsigned long vaddr; - - /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ - pagefault_disable(); - if (!PageHighMem(page)) - return page_address(page); - - debug_kmap_atomic(type); - idx = type + KM_TYPE_NR*smp_processor_id(); - vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx); -#ifdef CONFIG_DEBUG_HIGHMEM - BUG_ON(!pte_none(*(kmap_pte-idx))); -#endif - __set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot), 1); - local_flush_tlb_page(NULL, vaddr); - - return (void*) vaddr; -} - static inline void *kmap_atomic(struct page *page, enum km_type type) { return kmap_atomic_prot(page, type, kmap_prot); } -static inline void kunmap_atomic(void *kvaddr, enum km_type type) -{ -#ifdef CONFIG_DEBUG_HIGHMEM - unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK; - enum fixed_addresses idx = type + KM_TYPE_NR*smp_processor_id(); - - if (vaddr < __fix_to_virt(FIX_KMAP_END)) { - pagefault_enable(); - return; - } - - BUG_ON(vaddr != __fix_to_virt(FIX_KMAP_BEGIN + idx)); - - /* - * force other mappings to Oops if they'll try to access - * this pte without first remap it - */ - pte_clear(&init_mm, vaddr, kmap_pte-idx); - local_flush_tlb_page(NULL, vaddr); -#endif - pagefault_enable(); -} - static inline struct page *kmap_atomic_to_page(void *ptr) { unsigned long idx, vaddr = (unsigned long) ptr; @@ -148,6 +98,7 @@ static inline struct page *kmap_atomic_to_page(void *ptr) return pte_page(*pte); } + #define flush_cache_kmaps() flush_cache_all() #endif /* __KERNEL__ */ diff --git a/arch/powerpc/include/asm/hw_irq.h b/arch/powerpc/include/asm/hw_irq.h index 867ab8ed69b3..8b505eaaa38a 100644 --- a/arch/powerpc/include/asm/hw_irq.h +++ b/arch/powerpc/include/asm/hw_irq.h @@ -68,13 +68,13 @@ static inline int irqs_disabled_flags(unsigned long flags) #if defined(CONFIG_BOOKE) #define SET_MSR_EE(x) mtmsr(x) -#define local_irq_restore(flags) __asm__ __volatile__("wrtee %0" : : "r" (flags) : "memory") +#define raw_local_irq_restore(flags) __asm__ __volatile__("wrtee %0" : : "r" (flags) : "memory") #else #define SET_MSR_EE(x) mtmsr(x) -#define local_irq_restore(flags) mtmsr(flags) +#define raw_local_irq_restore(flags) mtmsr(flags) #endif -static inline void local_irq_disable(void) +static inline void raw_local_irq_disable(void) { #ifdef CONFIG_BOOKE __asm__ __volatile__("wrteei 0": : :"memory"); @@ -86,7 +86,7 @@ static inline void local_irq_disable(void) #endif } -static inline void local_irq_enable(void) +static inline void raw_local_irq_enable(void) { #ifdef CONFIG_BOOKE __asm__ __volatile__("wrteei 1": : :"memory"); @@ -98,7 +98,7 @@ static inline void local_irq_enable(void) #endif } -static inline void local_irq_save_ptr(unsigned long *flags) +static inline void raw_local_irq_save_ptr(unsigned long *flags) { unsigned long msr; msr = mfmsr(); @@ -110,12 +110,12 @@ static inline void local_irq_save_ptr(unsigned long *flags) #endif } -#define local_save_flags(flags) ((flags) = mfmsr()) -#define local_irq_save(flags) local_irq_save_ptr(&flags) -#define irqs_disabled() ((mfmsr() & MSR_EE) == 0) +#define raw_local_save_flags(flags) ((flags) = mfmsr()) +#define raw_local_irq_save(flags) raw_local_irq_save_ptr(&flags) +#define raw_irqs_disabled() ((mfmsr() & MSR_EE) == 0) +#define raw_irqs_disabled_flags(flags) (((flags) & MSR_EE) == 0) -#define hard_irq_enable() local_irq_enable() -#define hard_irq_disable() local_irq_disable() +#define hard_irq_disable() raw_local_irq_disable() static inline int irqs_disabled_flags(unsigned long flags) { diff --git a/arch/powerpc/include/asm/pte-hash64-64k.h b/arch/powerpc/include/asm/pte-hash64-64k.h index e05d26fa372f..82b72207c51c 100644 --- a/arch/powerpc/include/asm/pte-hash64-64k.h +++ b/arch/powerpc/include/asm/pte-hash64-64k.h @@ -47,7 +47,8 @@ * generic accessors and iterators here */ #define __real_pte(e,p) ((real_pte_t) { \ - (e), pte_val(*((p) + PTRS_PER_PTE)) }) + (e), ((e) & _PAGE_COMBO) ? \ + (pte_val(*((p) + PTRS_PER_PTE))) : 0 }) #define __rpte_to_hidx(r,index) ((pte_val((r).pte) & _PAGE_COMBO) ? \ (((r).hidx >> ((index)<<2)) & 0xf) : ((pte_val((r).pte) >> 12) & 0xf)) #define __rpte_to_pte(r) ((r).pte) diff --git a/arch/powerpc/include/asm/rtas.h b/arch/powerpc/include/asm/rtas.h index 01c12339b304..168fce726201 100644 --- a/arch/powerpc/include/asm/rtas.h +++ b/arch/powerpc/include/asm/rtas.h @@ -58,7 +58,7 @@ struct rtas_t { unsigned long entry; /* physical address pointer */ unsigned long base; /* physical address pointer */ unsigned long size; - spinlock_t lock; + raw_spinlock_t lock; struct rtas_args args; struct device_node *dev; /* virtual address pointer */ }; @@ -245,5 +245,8 @@ static inline u32 rtas_config_addr(int busno, int devfn, int reg) (devfn << 8) | (reg & 0xff); } +extern void __cpuinit rtas_give_timebase(void); +extern void __cpuinit rtas_take_timebase(void); + #endif /* __KERNEL__ */ #endif /* _POWERPC_RTAS_H */ diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S index 4dd38f129153..3cadba60a4b6 100644 --- a/arch/powerpc/kernel/entry_32.S +++ b/arch/powerpc/kernel/entry_32.S @@ -191,11 +191,49 @@ transfer_to_handler_cont: mflr r9 lwz r11,0(r9) /* virtual address of handler */ lwz r9,4(r9) /* where to go when done */ +#ifdef CONFIG_TRACE_IRQFLAGS + lis r12,reenable_mmu@h + ori r12,r12,reenable_mmu@l + mtspr SPRN_SRR0,r12 + mtspr SPRN_SRR1,r10 + SYNC + RFI +reenable_mmu: /* re-enable mmu so we can */ + mfmsr r10 + lwz r12,_MSR(r1) + xor r10,r10,r12 + andi. r10,r10,MSR_EE /* Did EE change? */ + beq 1f + + /* Save handler and return address into the 2 unused words + * of the STACK_FRAME_OVERHEAD (sneak sneak sneak). Everything + * else can be recovered from the pt_regs except r3 which for + * normal interrupts has been set to pt_regs and for syscalls + * is an argument, so we temporarily use ORIG_GPR3 to save it + */ + stw r9,8(r1) + stw r11,12(r1) + stw r3,ORIG_GPR3(r1) + bl trace_hardirqs_off + lwz r0,GPR0(r1) + lwz r3,ORIG_GPR3(r1) + lwz r4,GPR4(r1) + lwz r5,GPR5(r1) + lwz r6,GPR6(r1) + lwz r7,GPR7(r1) + lwz r8,GPR8(r1) + lwz r9,8(r1) + lwz r11,12(r1) +1: mtctr r11 + mtlr r9 + bctr /* jump to handler */ +#else /* CONFIG_TRACE_IRQFLAGS */ mtspr SPRN_SRR0,r11 mtspr SPRN_SRR1,r10 mtlr r9 SYNC RFI /* jump to handler, enable MMU */ +#endif /* CONFIG_TRACE_IRQFLAGS */ #if defined (CONFIG_6xx) || defined(CONFIG_E500) 4: rlwinm r12,r12,0,~_TLF_NAPPING @@ -251,6 +289,31 @@ _GLOBAL(DoSyscall) #ifdef SHOW_SYSCALLS bl do_show_syscall #endif /* SHOW_SYSCALLS */ +#ifdef CONFIG_TRACE_IRQFLAGS + /* Return from syscalls can (and generally will) hard enable + * interrupts. You aren't supposed to call a syscall with + * interrupts disabled in the first place. However, to ensure + * that we get it right vs. lockdep if it happens, we force + * that hard enable here with appropriate tracing if we see + * that we have been called with interrupts off + */ + mfmsr r11 + andi. r12,r11,MSR_EE + bne+ 1f + /* We came in with interrupts disabled, we enable them now */ + bl trace_hardirqs_on + mfmsr r11 + lwz r0,GPR0(r1) + lwz r3,GPR3(r1) + lwz r4,GPR4(r1) + ori r11,r11,MSR_EE + lwz r5,GPR5(r1) + lwz r6,GPR6(r1) + lwz r7,GPR7(r1) + lwz r8,GPR8(r1) + mtmsr r11 +1: +#endif /* CONFIG_TRACE_IRQFLAGS */ rlwinm r10,r1,0,0,(31-THREAD_SHIFT) /* current_thread_info() */ lwz r11,TI_FLAGS(r10) andi. r11,r11,_TIF_SYSCALL_T_OR_A @@ -275,6 +338,7 @@ ret_from_syscall: rlwinm r12,r1,0,0,(31-THREAD_SHIFT) /* current_thread_info() */ /* disable interrupts so current_thread_info()->flags can't change */ LOAD_MSR_KERNEL(r10,MSR_KERNEL) /* doesn't include MSR_EE */ + /* Note: We don't bother telling lockdep about it */ SYNC MTMSRD(r10) lwz r9,TI_FLAGS(r12) @@ -288,6 +352,19 @@ ret_from_syscall: oris r11,r11,0x1000 /* Set SO bit in CR */ stw r11,_CCR(r1) syscall_exit_cont: + lwz r8,_MSR(r1) +#ifdef CONFIG_TRACE_IRQFLAGS + /* If we are going to return from the syscall with interrupts + * off, we trace that here. It shouldn't happen though but we + * want to catch the bugger if it does right ? + */ + andi. r10,r8,MSR_EE + bne+ 1f + stw r3,GPR3(r1) + bl trace_hardirqs_off + lwz r3,GPR3(r1) +1: +#endif /* CONFIG_TRACE_IRQFLAGS */ #if defined(CONFIG_4xx) || defined(CONFIG_BOOKE) /* If the process has its own DBCR0 value, load it up. The internal debug mode bit tells us that dbcr0 should be loaded. */ @@ -311,7 +388,6 @@ END_FTR_SECTION_IFSET(CPU_FTR_NEED_PAIRED_STWCX) mtlr r4 mtcr r5 lwz r7,_NIP(r1) - lwz r8,_MSR(r1) FIX_SRR1(r8, r0) lwz r2,GPR2(r1) lwz r1,GPR1(r1) @@ -394,7 +470,9 @@ syscall_exit_work: andi. r0,r9,(_TIF_SYSCALL_T_OR_A|_TIF_SINGLESTEP) beq ret_from_except - /* Re-enable interrupts */ + /* Re-enable interrupts. There is no need to trace that with + * lockdep as we are supposed to have IRQs on at this point + */ ori r10,r10,MSR_EE SYNC MTMSRD(r10) @@ -705,6 +783,7 @@ ret_from_except: /* Hard-disable interrupts so that current_thread_info()->flags * can't change between when we test it and when we return * from the interrupt. */ + /* Note: We don't bother telling lockdep about it */ LOAD_MSR_KERNEL(r10,MSR_KERNEL) SYNC /* Some chip revs have problems here... */ MTMSRD(r10) /* disable interrupts */ @@ -744,11 +823,24 @@ resume_kernel: beq+ restore andi. r0,r3,MSR_EE /* interrupts off? */ beq restore /* don't schedule if so */ +#ifdef CONFIG_TRACE_IRQFLAGS + /* Lockdep thinks irqs are enabled, we need to call + * preempt_schedule_irq with IRQs off, so we inform lockdep + * now that we -did- turn them off already + */ + bl trace_hardirqs_off +#endif 1: bl preempt_schedule_irq rlwinm r9,r1,0,0,(31-THREAD_SHIFT) lwz r3,TI_FLAGS(r9) andi. r0,r3,_TIF_NEED_RESCHED bne- 1b +#ifdef CONFIG_TRACE_IRQFLAGS + /* And now, to properly rebalance the above, we tell lockdep they + * are being turned back on, which will happen when we return + */ + bl trace_hardirqs_on +#endif #else resume_kernel: #endif /* CONFIG_PREEMPT */ @@ -765,6 +857,28 @@ restore: stw r6,icache_44x_need_flush@l(r4) 1: #endif /* CONFIG_44x */ + + lwz r9,_MSR(r1) +#ifdef CONFIG_TRACE_IRQFLAGS + /* Lockdep doesn't know about the fact that IRQs are temporarily turned + * off in this assembly code while peeking at TI_FLAGS() and such. However + * we need to inform it if the exception turned interrupts off, and we + * are about to trun them back on. + * + * The problem here sadly is that we don't know whether the exceptions was + * one that turned interrupts off or not. So we always tell lockdep about + * turning them on here when we go back to wherever we came from with EE + * on, even if that may meen some redudant calls being tracked. Maybe later + * we could encode what the exception did somewhere or test the exception + * type in the pt_regs but that sounds overkill + */ + andi. r10,r9,MSR_EE + beq 1f + bl trace_hardirqs_on + lwz r9,_MSR(r1) +1: +#endif /* CONFIG_TRACE_IRQFLAGS */ + lwz r0,GPR0(r1) lwz r2,GPR2(r1) REST_4GPRS(3, r1) @@ -782,7 +896,6 @@ END_FTR_SECTION_IFSET(CPU_FTR_NEED_PAIRED_STWCX) stwcx. r0,0,r1 /* to clear the reservation */ #if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE)) - lwz r9,_MSR(r1) andi. r10,r9,MSR_RI /* check if this exception occurred */ beql nonrecoverable /* at a bad place (MSR:RI = 0) */ @@ -805,7 +918,6 @@ END_FTR_SECTION_IFSET(CPU_FTR_NEED_PAIRED_STWCX) MTMSRD(r10) /* clear the RI bit */ .globl exc_exit_restart exc_exit_restart: - lwz r9,_MSR(r1) lwz r12,_NIP(r1) FIX_SRR1(r9,r10) mtspr SPRN_SRR0,r12 @@ -1035,11 +1147,18 @@ do_work: /* r10 contains MSR_KERNEL here */ beq do_user_signal do_resched: /* r10 contains MSR_KERNEL here */ + /* Note: We don't need to inform lockdep that we are enabling + * interrupts here. As far as it knows, they are already enabled + */ ori r10,r10,MSR_EE SYNC MTMSRD(r10) /* hard-enable interrupts */ bl schedule recheck: + /* Note: And we don't tell it we are disabling them again + * neither. Those disable/enable cycles used to peek at + * TI_FLAGS aren't advertised. + */ LOAD_MSR_KERNEL(r10,MSR_KERNEL) SYNC MTMSRD(r10) /* disable interrupts */ diff --git a/arch/powerpc/kernel/head_32.S b/arch/powerpc/kernel/head_32.S index 48469463f89e..fc2132942754 100644 --- a/arch/powerpc/kernel/head_32.S +++ b/arch/powerpc/kernel/head_32.S @@ -1124,9 +1124,8 @@ mmu_off: RFI /* - * Use the first pair of BAT registers to map the 1st 16MB - * of RAM to PAGE_OFFSET. From this point on we can't safely - * call OF any more. + * On 601, we use 3 BATs to map up to 24M of RAM at _PAGE_OFFSET + * (we keep one for debugging) and on others, we use one 256M BAT. */ initial_bats: lis r11,PAGE_OFFSET@h @@ -1136,12 +1135,16 @@ initial_bats: bne 4f ori r11,r11,4 /* set up BAT registers for 601 */ li r8,0x7f /* valid, block length = 8MB */ - oris r9,r11,0x800000@h /* set up BAT reg for 2nd 8M */ - oris r10,r8,0x800000@h /* set up BAT reg for 2nd 8M */ mtspr SPRN_IBAT0U,r11 /* N.B. 601 has valid bit in */ mtspr SPRN_IBAT0L,r8 /* lower BAT register */ - mtspr SPRN_IBAT1U,r9 - mtspr SPRN_IBAT1L,r10 + addis r11,r11,0x800000@h + addis r8,r8,0x800000@h + mtspr SPRN_IBAT1U,r11 + mtspr SPRN_IBAT1L,r8 + addis r11,r11,0x800000@h + addis r8,r8,0x800000@h + mtspr SPRN_IBAT2U,r11 + mtspr SPRN_IBAT2L,r8 isync blr diff --git a/arch/powerpc/kernel/of_device.c b/arch/powerpc/kernel/of_device.c index fa983a59c4ce..a359cb08e900 100644 --- a/arch/powerpc/kernel/of_device.c +++ b/arch/powerpc/kernel/of_device.c @@ -76,7 +76,7 @@ struct of_device *of_device_alloc(struct device_node *np, dev->dev.archdata.of_node = np; if (bus_id) - dev_set_name(&dev->dev, bus_id); + dev_set_name(&dev->dev, "%s", bus_id); else of_device_make_bus_id(dev); diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c index 3e7135bbe40f..892a9f2e6d76 100644 --- a/arch/powerpc/kernel/process.c +++ b/arch/powerpc/kernel/process.c @@ -528,7 +528,7 @@ void show_regs(struct pt_regs * regs) for (i = 0; i < 32; i++) { if ((i % REGS_PER_LINE) == 0) - printk("\n" KERN_INFO "GPR%02d: ", i); + printk("\nGPR%02d: ", i); printk(REG " ", regs->gpr[i]); if (i == LAST_VOLATILE && !FULL_REGS(regs)) break; diff --git a/arch/powerpc/kernel/rtas.c b/arch/powerpc/kernel/rtas.c index ee4c7609b649..c434823b8c83 100644 --- a/arch/powerpc/kernel/rtas.c +++ b/arch/powerpc/kernel/rtas.c @@ -38,9 +38,10 @@ #include #include #include +#include struct rtas_t rtas = { - .lock = SPIN_LOCK_UNLOCKED + .lock = __RAW_SPIN_LOCK_UNLOCKED }; EXPORT_SYMBOL(rtas); @@ -67,6 +68,28 @@ unsigned long rtas_rmo_buf; void (*rtas_flash_term_hook)(int); EXPORT_SYMBOL(rtas_flash_term_hook); +/* RTAS use home made raw locking instead of spin_lock_irqsave + * because those can be called from within really nasty contexts + * such as having the timebase stopped which would lockup with + * normal locks and spinlock debugging enabled + */ +static unsigned long lock_rtas(void) +{ + unsigned long flags; + + local_irq_save(flags); + preempt_disable(); + __raw_spin_lock_flags(&rtas.lock, flags); + return flags; +} + +static void unlock_rtas(unsigned long flags) +{ + __raw_spin_unlock(&rtas.lock); + local_irq_restore(flags); + preempt_enable(); +} + /* * call_rtas_display_status and call_rtas_display_status_delay * are designed only for very early low-level debugging, which @@ -79,7 +102,7 @@ static void call_rtas_display_status(char c) if (!rtas.base) return; - spin_lock_irqsave(&rtas.lock, s); + s = lock_rtas(); args->token = 10; args->nargs = 1; @@ -89,7 +112,7 @@ static void call_rtas_display_status(char c) enter_rtas(__pa(args)); - spin_unlock_irqrestore(&rtas.lock, s); + unlock_rtas(s); } static void call_rtas_display_status_delay(char c) @@ -411,8 +434,7 @@ int rtas_call(int token, int nargs, int nret, int *outputs, ...) if (!rtas.entry || token == RTAS_UNKNOWN_SERVICE) return -1; - /* Gotta do something different here, use global lock for now... */ - spin_lock_irqsave(&rtas.lock, s); + s = lock_rtas(); rtas_args = &rtas.args; rtas_args->token = token; @@ -439,8 +461,7 @@ int rtas_call(int token, int nargs, int nret, int *outputs, ...) outputs[i] = rtas_args->rets[i+1]; ret = (nret > 0)? rtas_args->rets[0]: 0; - /* Gotta do something different here, use global lock for now... */ - spin_unlock_irqrestore(&rtas.lock, s); + unlock_rtas(s); if (buff_copy) { log_error(buff_copy, ERR_TYPE_RTAS_LOG, 0); @@ -837,7 +858,7 @@ asmlinkage int ppc_rtas(struct rtas_args __user *uargs) buff_copy = get_errorlog_buffer(); - spin_lock_irqsave(&rtas.lock, flags); + flags = lock_rtas(); rtas.args = args; enter_rtas(__pa(&rtas.args)); @@ -848,7 +869,7 @@ asmlinkage int ppc_rtas(struct rtas_args __user *uargs) if (args.rets[0] == -1) errbuf = __fetch_rtas_last_error(buff_copy); - spin_unlock_irqrestore(&rtas.lock, flags); + unlock_rtas(flags); if (buff_copy) { if (errbuf) @@ -951,3 +972,33 @@ int __init early_init_dt_scan_rtas(unsigned long node, /* break now */ return 1; } + +static raw_spinlock_t timebase_lock; +static u64 timebase = 0; + +void __cpuinit rtas_give_timebase(void) +{ + unsigned long flags; + + local_irq_save(flags); + hard_irq_disable(); + __raw_spin_lock(&timebase_lock); + rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL); + timebase = get_tb(); + __raw_spin_unlock(&timebase_lock); + + while (timebase) + barrier(); + rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL); + local_irq_restore(flags); +} + +void __cpuinit rtas_take_timebase(void) +{ + while (!timebase) + barrier(); + __raw_spin_lock(&timebase_lock); + set_tb(timebase >> 32, timebase & 0xffffffff); + timebase = 0; + __raw_spin_unlock(&timebase_lock); +} diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c index 1d154248cf40..e1e3059cf34b 100644 --- a/arch/powerpc/kernel/setup_32.c +++ b/arch/powerpc/kernel/setup_32.c @@ -119,6 +119,8 @@ notrace unsigned long __init early_init(unsigned long dt_ptr) */ notrace void __init machine_init(unsigned long dt_ptr) { + lockdep_init(); + /* Enable early debugging if any specified (see udbg.h) */ udbg_early_init(); diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c index 65484b2200b3..0b47de07302d 100644 --- a/arch/powerpc/kernel/smp.c +++ b/arch/powerpc/kernel/smp.c @@ -68,7 +68,8 @@ EXPORT_PER_CPU_SYMBOL(cpu_core_map); /* SMP operations for this machine */ struct smp_ops_t *smp_ops; -static volatile unsigned int cpu_callin_map[NR_CPUS]; +/* Can't be static due to PowerMac hackery */ +volatile unsigned int cpu_callin_map[NR_CPUS]; int smt_enabled_at_boot = 1; diff --git a/arch/powerpc/kernel/udbg_16550.c b/arch/powerpc/kernel/udbg_16550.c index 0362a891e54e..acb74a17bbbf 100644 --- a/arch/powerpc/kernel/udbg_16550.c +++ b/arch/powerpc/kernel/udbg_16550.c @@ -219,7 +219,7 @@ void udbg_init_pas_realmode(void) #ifdef CONFIG_PPC_EARLY_DEBUG_44x #include -static int udbg_44x_as1_flush(void) +static void udbg_44x_as1_flush(void) { if (udbg_comport) { while ((as1_readb(&udbg_comport->lsr) & LSR_THRE) == 0) diff --git a/arch/powerpc/mm/Makefile b/arch/powerpc/mm/Makefile index 2d2192e48de7..3e68363405b7 100644 --- a/arch/powerpc/mm/Makefile +++ b/arch/powerpc/mm/Makefile @@ -30,3 +30,4 @@ obj-$(CONFIG_PPC_MM_SLICES) += slice.o obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o obj-$(CONFIG_PPC_SUBPAGE_PROT) += subpage-prot.o obj-$(CONFIG_NOT_COHERENT_CACHE) += dma-noncoherent.o +obj-$(CONFIG_HIGHMEM) += highmem.o diff --git a/arch/powerpc/mm/highmem.c b/arch/powerpc/mm/highmem.c new file mode 100644 index 000000000000..c2186c74c85a --- /dev/null +++ b/arch/powerpc/mm/highmem.c @@ -0,0 +1,77 @@ +/* + * highmem.c: virtual kernel memory mappings for high memory + * + * PowerPC version, stolen from the i386 version. + * + * Used in CONFIG_HIGHMEM systems for memory pages which + * are not addressable by direct kernel virtual addresses. + * + * Copyright (C) 1999 Gerhard Wichert, Siemens AG + * Gerhard.Wichert@pdb.siemens.de + * + * + * Redesigned the x86 32-bit VM architecture to deal with + * up to 16 Terrabyte physical memory. With current x86 CPUs + * we now support up to 64 Gigabytes physical RAM. + * + * Copyright (C) 1999 Ingo Molnar + * + * Reworked for PowerPC by various contributors. Moved from + * highmem.h by Benjamin Herrenschmidt (c) 2009 IBM Corp. + */ + +#include +#include + +/* + * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap + * gives a more generic (and caching) interface. But kmap_atomic can + * be used in IRQ contexts, so in some (very limited) cases we need + * it. + */ +void *kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot) +{ + unsigned int idx; + unsigned long vaddr; + + /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ + pagefault_disable(); + if (!PageHighMem(page)) + return page_address(page); + + debug_kmap_atomic(type); + idx = type + KM_TYPE_NR*smp_processor_id(); + vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx); +#ifdef CONFIG_DEBUG_HIGHMEM + BUG_ON(!pte_none(*(kmap_pte-idx))); +#endif + __set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot), 1); + local_flush_tlb_page(NULL, vaddr); + + return (void*) vaddr; +} +EXPORT_SYMBOL(kmap_atomic_prot); + +void kunmap_atomic(void *kvaddr, enum km_type type) +{ +#ifdef CONFIG_DEBUG_HIGHMEM + unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK; + enum fixed_addresses idx = type + KM_TYPE_NR*smp_processor_id(); + + if (vaddr < __fix_to_virt(FIX_KMAP_END)) { + pagefault_enable(); + return; + } + + BUG_ON(vaddr != __fix_to_virt(FIX_KMAP_BEGIN + idx)); + + /* + * force other mappings to Oops if they'll try to access + * this pte without first remap it + */ + pte_clear(&init_mm, vaddr, kmap_pte-idx); + local_flush_tlb_page(NULL, vaddr); +#endif + pagefault_enable(); +} +EXPORT_SYMBOL(kunmap_atomic); diff --git a/arch/powerpc/platforms/44x/warp.c b/arch/powerpc/platforms/44x/warp.c index 42e09a9f77e2..0362c88f47d7 100644 --- a/arch/powerpc/platforms/44x/warp.c +++ b/arch/powerpc/platforms/44x/warp.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include @@ -65,7 +66,6 @@ define_machine(warp) { static u32 post_info; -/* I am not sure this is the best place for this... */ static int __init warp_post_info(void) { struct device_node *np; @@ -194,9 +194,9 @@ static int pika_setup_leds(void) return 0; } -static void pika_setup_critical_temp(struct i2c_client *client) +static void pika_setup_critical_temp(struct device_node *np, + struct i2c_client *client) { - struct device_node *np; int irq, rc; /* Do this before enabling critical temp interrupt since we @@ -208,14 +208,7 @@ static void pika_setup_critical_temp(struct i2c_client *client) i2c_smbus_write_byte_data(client, 2, 65); /* Thigh */ i2c_smbus_write_byte_data(client, 3, 0); /* Tlow */ - np = of_find_compatible_node(NULL, NULL, "adi,ad7414"); - if (np == NULL) { - printk(KERN_ERR __FILE__ ": Unable to find ad7414\n"); - return; - } - irq = irq_of_parse_and_map(np, 0); - of_node_put(np); if (irq == NO_IRQ) { printk(KERN_ERR __FILE__ ": Unable to get ad7414 irq\n"); return; @@ -244,32 +237,24 @@ static inline void pika_dtm_check_fan(void __iomem *fpga) static int pika_dtm_thread(void __iomem *fpga) { - struct i2c_adapter *adap; + struct device_node *np; struct i2c_client *client; - /* We loop in case either driver was compiled as a module and - * has not been insmoded yet. - */ - while (!(adap = i2c_get_adapter(0))) { - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(HZ); + np = of_find_compatible_node(NULL, NULL, "adi,ad7414"); + if (np == NULL) + return -ENOENT; + + client = of_find_i2c_device_by_node(np); + if (client == NULL) { + of_node_put(np); + return -ENOENT; } - while (1) { - list_for_each_entry(client, &adap->clients, list) - if (client->addr == 0x4a) - goto found_it; + pika_setup_critical_temp(np, client); - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(HZ); - } + of_node_put(np); -found_it: - pika_setup_critical_temp(client); - - i2c_put_adapter(adap); - - printk(KERN_INFO "PIKA DTM thread running.\n"); + printk(KERN_INFO "Warp DTM thread running.\n"); while (!kthread_should_stop()) { int val; @@ -291,7 +276,6 @@ found_it: return 0; } - static int __init pika_dtm_start(void) { struct task_struct *dtm_thread; diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c index 77f90b356356..60ed9c067b1d 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c @@ -285,6 +285,7 @@ static struct of_device_id mpc85xx_ids[] = { { .type = "qe", }, { .compatible = "fsl,qe", }, { .compatible = "gianfar", }, + { .compatible = "fsl,rapidio-delta", }, {}, }; diff --git a/arch/powerpc/platforms/85xx/smp.c b/arch/powerpc/platforms/85xx/smp.c index cc0b0db8a6f3..62c592ede641 100644 --- a/arch/powerpc/platforms/85xx/smp.c +++ b/arch/powerpc/platforms/85xx/smp.c @@ -52,20 +52,19 @@ smp_85xx_kick_cpu(int nr) pr_debug("smp_85xx_kick_cpu: kick CPU #%d\n", nr); - local_irq_save(flags); - np = of_get_cpu_node(nr, NULL); cpu_rel_addr = of_get_property(np, "cpu-release-addr", NULL); if (cpu_rel_addr == NULL) { printk(KERN_ERR "No cpu-release-addr for cpu %d\n", nr); - local_irq_restore(flags); return; } /* Map the spin table */ bptr_vaddr = ioremap(*cpu_rel_addr, SIZE_BOOT_ENTRY); + local_irq_save(flags); + out_be32(bptr_vaddr + BOOT_ENTRY_PIR, nr); out_be32(bptr_vaddr + BOOT_ENTRY_ADDR_LOWER, __pa(__early_start)); @@ -73,10 +72,10 @@ smp_85xx_kick_cpu(int nr) while ((__secondary_hold_acknowledge != nr) && (++n < 1000)) mdelay(1); - iounmap(bptr_vaddr); - local_irq_restore(flags); + iounmap(bptr_vaddr); + pr_debug("waited %d msecs for CPU #%d.\n", n, nr); } diff --git a/arch/powerpc/platforms/85xx/socrates.c b/arch/powerpc/platforms/85xx/socrates.c index d0e8443b12c6..747d8fb3ab82 100644 --- a/arch/powerpc/platforms/85xx/socrates.c +++ b/arch/powerpc/platforms/85xx/socrates.c @@ -102,10 +102,11 @@ static struct of_device_id __initdata socrates_of_bus_ids[] = { {}, }; -static void __init socrates_init(void) +static int __init socrates_publish_devices(void) { - of_platform_bus_probe(NULL, socrates_of_bus_ids, NULL); + return of_platform_bus_probe(NULL, socrates_of_bus_ids, NULL); } +machine_device_initcall(socrates, socrates_publish_devices); /* * Called very early, device-tree isn't unflattened @@ -124,7 +125,6 @@ define_machine(socrates) { .name = "Socrates", .probe = socrates_probe, .setup_arch = socrates_setup_arch, - .init = socrates_init, .init_IRQ = socrates_pic_init, .get_irq = mpic_get_irq, .restart = fsl_rstcr_restart, diff --git a/arch/powerpc/platforms/85xx/xes_mpc85xx.c b/arch/powerpc/platforms/85xx/xes_mpc85xx.c index ee01532786e4..1b426050a2f9 100644 --- a/arch/powerpc/platforms/85xx/xes_mpc85xx.c +++ b/arch/powerpc/platforms/85xx/xes_mpc85xx.c @@ -32,7 +32,6 @@ #include #include -#include /* A few bit definitions needed for fixups on some boards */ #define MPC85xx_L2CTL_L2E 0x80000000 /* L2 enable */ diff --git a/arch/powerpc/platforms/cell/smp.c b/arch/powerpc/platforms/cell/smp.c index 9046803c8276..bc97fada48c6 100644 --- a/arch/powerpc/platforms/cell/smp.c +++ b/arch/powerpc/platforms/cell/smp.c @@ -36,7 +36,6 @@ #include #include #include -#include #include #include #include @@ -140,31 +139,6 @@ static void __devinit smp_cell_setup_cpu(int cpu) mtspr(SPRN_DABRX, DABRX_KERNEL | DABRX_USER); } -static DEFINE_SPINLOCK(timebase_lock); -static unsigned long timebase = 0; - -static void __devinit cell_give_timebase(void) -{ - spin_lock(&timebase_lock); - rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL); - timebase = get_tb(); - spin_unlock(&timebase_lock); - - while (timebase) - barrier(); - rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL); -} - -static void __devinit cell_take_timebase(void) -{ - while (!timebase) - barrier(); - spin_lock(&timebase_lock); - set_tb(timebase >> 32, timebase & 0xffffffff); - timebase = 0; - spin_unlock(&timebase_lock); -} - static void __devinit smp_cell_kick_cpu(int nr) { BUG_ON(nr < 0 || nr >= NR_CPUS); @@ -224,8 +198,8 @@ void __init smp_init_cell(void) /* Non-lpar has additional take/give timebase */ if (rtas_token("freeze-time-base") != RTAS_UNKNOWN_SERVICE) { - smp_ops->give_timebase = cell_give_timebase; - smp_ops->take_timebase = cell_take_timebase; + smp_ops->give_timebase = rtas_give_timebase; + smp_ops->take_timebase = rtas_take_timebase; } DBG(" <- smp_init_cell()\n"); diff --git a/arch/powerpc/platforms/chrp/smp.c b/arch/powerpc/platforms/chrp/smp.c index 10a4a4d063b6..02cafecc90e3 100644 --- a/arch/powerpc/platforms/chrp/smp.c +++ b/arch/powerpc/platforms/chrp/smp.c @@ -26,7 +26,6 @@ #include #include #include -#include #include #include #include @@ -42,40 +41,12 @@ static void __devinit smp_chrp_setup_cpu(int cpu_nr) mpic_setup_this_cpu(); } -static DEFINE_SPINLOCK(timebase_lock); -static unsigned int timebase_upper = 0, timebase_lower = 0; - -void __devinit smp_chrp_give_timebase(void) -{ - spin_lock(&timebase_lock); - rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL); - timebase_upper = get_tbu(); - timebase_lower = get_tbl(); - spin_unlock(&timebase_lock); - - while (timebase_upper || timebase_lower) - barrier(); - rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL); -} - -void __devinit smp_chrp_take_timebase(void) -{ - while (!(timebase_upper || timebase_lower)) - barrier(); - spin_lock(&timebase_lock); - set_tb(timebase_upper, timebase_lower); - timebase_upper = 0; - timebase_lower = 0; - spin_unlock(&timebase_lock); - printk("CPU %i taken timebase\n", smp_processor_id()); -} - /* CHRP with openpic */ struct smp_ops_t chrp_smp_ops = { .message_pass = smp_mpic_message_pass, .probe = smp_mpic_probe, .kick_cpu = smp_chrp_kick_cpu, .setup_cpu = smp_chrp_setup_cpu, - .give_timebase = smp_chrp_give_timebase, - .take_timebase = smp_chrp_take_timebase, + .give_timebase = rtas_give_timebase, + .take_timebase = rtas_take_timebase, }; diff --git a/arch/powerpc/platforms/pasemi/setup.c b/arch/powerpc/platforms/pasemi/setup.c index 153051eb6d93..a4619347aa7e 100644 --- a/arch/powerpc/platforms/pasemi/setup.c +++ b/arch/powerpc/platforms/pasemi/setup.c @@ -71,20 +71,25 @@ static void pas_restart(char *cmd) } #ifdef CONFIG_SMP -static DEFINE_SPINLOCK(timebase_lock); +static raw_spinlock_t timebase_lock; static unsigned long timebase; static void __devinit pas_give_timebase(void) { - spin_lock(&timebase_lock); + unsigned long flags; + + local_irq_save(flags); + hard_irq_disable(); + __raw_spin_lock(&timebase_lock); mtspr(SPRN_TBCTL, TBCTL_FREEZE); isync(); timebase = get_tb(); - spin_unlock(&timebase_lock); + __raw_spin_unlock(&timebase_lock); while (timebase) barrier(); mtspr(SPRN_TBCTL, TBCTL_RESTART); + local_irq_restore(flags); } static void __devinit pas_take_timebase(void) @@ -92,10 +97,10 @@ static void __devinit pas_take_timebase(void) while (!timebase) smp_rmb(); - spin_lock(&timebase_lock); + __raw_spin_lock(&timebase_lock); set_tb(timebase >> 32, timebase & 0xffffffff); timebase = 0; - spin_unlock(&timebase_lock); + __raw_spin_unlock(&timebase_lock); } struct smp_ops_t pas_smp_ops = { diff --git a/arch/powerpc/platforms/powermac/setup.c b/arch/powerpc/platforms/powermac/setup.c index 86f69a4eb49b..c20522656367 100644 --- a/arch/powerpc/platforms/powermac/setup.c +++ b/arch/powerpc/platforms/powermac/setup.c @@ -103,11 +103,6 @@ unsigned long smu_cmdbuf_abs; EXPORT_SYMBOL(smu_cmdbuf_abs); #endif -#ifdef CONFIG_SMP -extern struct smp_ops_t psurge_smp_ops; -extern struct smp_ops_t core99_smp_ops; -#endif /* CONFIG_SMP */ - static void pmac_show_cpuinfo(struct seq_file *m) { struct device_node *np; @@ -341,34 +336,6 @@ static void __init pmac_setup_arch(void) ROOT_DEV = DEFAULT_ROOT_DEVICE; #endif -#ifdef CONFIG_SMP - /* Check for Core99 */ - ic = of_find_node_by_name(NULL, "uni-n"); - if (!ic) - ic = of_find_node_by_name(NULL, "u3"); - if (!ic) - ic = of_find_node_by_name(NULL, "u4"); - if (ic) { - of_node_put(ic); - smp_ops = &core99_smp_ops; - } -#ifdef CONFIG_PPC32 - else { - /* - * We have to set bits in cpu_possible_map here since the - * secondary CPU(s) aren't in the device tree, and - * setup_per_cpu_areas only allocates per-cpu data for - * CPUs in the cpu_possible_map. - */ - int cpu; - - for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu) - cpu_set(cpu, cpu_possible_map); - smp_ops = &psurge_smp_ops; - } -#endif -#endif /* CONFIG_SMP */ - #ifdef CONFIG_ADB if (strstr(cmd_line, "adb_sync")) { extern int __adb_probe_sync; @@ -512,6 +479,14 @@ static void __init pmac_init_early(void) #ifdef CONFIG_PPC64 iommu_init_early_dart(); #endif + + /* SMP Init has to be done early as we need to patch up + * cpu_possible_map before interrupt stacks are allocated + * or kaboom... + */ +#ifdef CONFIG_SMP + pmac_setup_smp(); +#endif } static int __init pmac_declare_of_platform_devices(void) diff --git a/arch/powerpc/platforms/powermac/smp.c b/arch/powerpc/platforms/powermac/smp.c index cf1dbe758890..6d4da7b46b41 100644 --- a/arch/powerpc/platforms/powermac/smp.c +++ b/arch/powerpc/platforms/powermac/smp.c @@ -64,10 +64,11 @@ extern void __secondary_start_pmac_0(void); extern int pmac_pfunc_base_install(void); -#ifdef CONFIG_PPC32 +static void (*pmac_tb_freeze)(int freeze); +static u64 timebase; +static int tb_req; -/* Sync flag for HW tb sync */ -static volatile int sec_tb_reset = 0; +#ifdef CONFIG_PPC32 /* * Powersurge (old powermac SMP) support. @@ -294,6 +295,9 @@ static int __init smp_psurge_probe(void) psurge_quad_init(); /* All released cards using this HW design have 4 CPUs */ ncpus = 4; + /* No sure how timebase sync works on those, let's use SW */ + smp_ops->give_timebase = smp_generic_give_timebase; + smp_ops->take_timebase = smp_generic_take_timebase; } else { iounmap(quad_base); if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) { @@ -308,18 +312,15 @@ static int __init smp_psurge_probe(void) psurge_start = ioremap(PSURGE_START, 4); psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4); - /* - * This is necessary because OF doesn't know about the + /* This is necessary because OF doesn't know about the * secondary cpu(s), and thus there aren't nodes in the * device tree for them, and smp_setup_cpu_maps hasn't - * set their bits in cpu_possible_map and cpu_present_map. + * set their bits in cpu_present_map. */ if (ncpus > NR_CPUS) ncpus = NR_CPUS; - for (i = 1; i < ncpus ; ++i) { + for (i = 1; i < ncpus ; ++i) cpu_set(i, cpu_present_map); - set_hard_smp_processor_id(i, i); - } if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352); @@ -329,8 +330,14 @@ static int __init smp_psurge_probe(void) static void __init smp_psurge_kick_cpu(int nr) { unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8; - unsigned long a; - int i; + unsigned long a, flags; + int i, j; + + /* Defining this here is evil ... but I prefer hiding that + * crap to avoid giving people ideas that they can do the + * same. + */ + extern volatile unsigned int cpu_callin_map[NR_CPUS]; /* may need to flush here if secondary bats aren't setup */ for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32) @@ -339,47 +346,52 @@ static void __init smp_psurge_kick_cpu(int nr) if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353); + /* This is going to freeze the timeebase, we disable interrupts */ + local_irq_save(flags); + out_be32(psurge_start, start); mb(); psurge_set_ipi(nr); + /* * We can't use udelay here because the timebase is now frozen. */ for (i = 0; i < 2000; ++i) - barrier(); + asm volatile("nop" : : : "memory"); psurge_clr_ipi(nr); - if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354); -} - -/* - * With the dual-cpu powersurge board, the decrementers and timebases - * of both cpus are frozen after the secondary cpu is started up, - * until we give the secondary cpu another interrupt. This routine - * uses this to get the timebases synchronized. - * -- paulus. - */ -static void __init psurge_dual_sync_tb(int cpu_nr) -{ - int t; - - set_dec(tb_ticks_per_jiffy); - /* XXX fixme */ - set_tb(0, 0); - - if (cpu_nr > 0) { - mb(); - sec_tb_reset = 1; - return; + /* + * Also, because the timebase is frozen, we must not return to the + * caller which will try to do udelay's etc... Instead, we wait -here- + * for the CPU to callin. + */ + for (i = 0; i < 100000 && !cpu_callin_map[nr]; ++i) { + for (j = 1; j < 10000; j++) + asm volatile("nop" : : : "memory"); + asm volatile("sync" : : : "memory"); } + if (!cpu_callin_map[nr]) + goto stuck; - /* wait for the secondary to have reset its TB before proceeding */ - for (t = 10000000; t > 0 && !sec_tb_reset; --t) - ; + /* And we do the TB sync here too for standard dual CPU cards */ + if (psurge_type == PSURGE_DUAL) { + while(!tb_req) + barrier(); + tb_req = 0; + mb(); + timebase = get_tb(); + mb(); + while (timebase) + barrier(); + mb(); + } + stuck: + /* now interrupt the secondary, restarting both TBs */ + if (psurge_type == PSURGE_DUAL) + psurge_set_ipi(1); - /* now interrupt the secondary, starting both TBs */ - psurge_set_ipi(1); + if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354); } static struct irqaction psurge_irqaction = { @@ -390,36 +402,35 @@ static struct irqaction psurge_irqaction = { static void __init smp_psurge_setup_cpu(int cpu_nr) { + if (cpu_nr != 0) + return; - if (cpu_nr == 0) { - /* If we failed to start the second CPU, we should still - * send it an IPI to start the timebase & DEC or we might - * have them stuck. - */ - if (num_online_cpus() < 2) { - if (psurge_type == PSURGE_DUAL) - psurge_set_ipi(1); - return; - } - /* reset the entry point so if we get another intr we won't - * try to startup again */ - out_be32(psurge_start, 0x100); - if (setup_irq(30, &psurge_irqaction)) - printk(KERN_ERR "Couldn't get primary IPI interrupt"); - } - - if (psurge_type == PSURGE_DUAL) - psurge_dual_sync_tb(cpu_nr); + /* reset the entry point so if we get another intr we won't + * try to startup again */ + out_be32(psurge_start, 0x100); + if (setup_irq(30, &psurge_irqaction)) + printk(KERN_ERR "Couldn't get primary IPI interrupt"); } void __init smp_psurge_take_timebase(void) { - /* Dummy implementation */ + if (psurge_type != PSURGE_DUAL) + return; + + tb_req = 1; + mb(); + while (!timebase) + barrier(); + mb(); + set_tb(timebase >> 32, timebase & 0xffffffff); + timebase = 0; + mb(); + set_dec(tb_ticks_per_jiffy/2); } void __init smp_psurge_give_timebase(void) { - /* Dummy implementation */ + /* Nothing to do here */ } /* PowerSurge-style Macs */ @@ -437,9 +448,6 @@ struct smp_ops_t psurge_smp_ops = { * Core 99 and later support */ -static void (*pmac_tb_freeze)(int freeze); -static u64 timebase; -static int tb_req; static void smp_core99_give_timebase(void) { @@ -478,7 +486,6 @@ static void __devinit smp_core99_take_timebase(void) set_tb(timebase >> 32, timebase & 0xffffffff); timebase = 0; mb(); - set_dec(tb_ticks_per_jiffy/2); local_irq_restore(flags); } @@ -920,3 +927,34 @@ struct smp_ops_t core99_smp_ops = { # endif #endif }; + +void __init pmac_setup_smp(void) +{ + struct device_node *np; + + /* Check for Core99 */ + np = of_find_node_by_name(NULL, "uni-n"); + if (!np) + np = of_find_node_by_name(NULL, "u3"); + if (!np) + np = of_find_node_by_name(NULL, "u4"); + if (np) { + of_node_put(np); + smp_ops = &core99_smp_ops; + } +#ifdef CONFIG_PPC32 + else { + /* We have to set bits in cpu_possible_map here since the + * secondary CPU(s) aren't in the device tree. Various + * things won't be initialized for CPUs not in the possible + * map, so we really need to fix it up here. + */ + int cpu; + + for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu) + cpu_set(cpu, cpu_possible_map); + smp_ops = &psurge_smp_ops; + } +#endif /* CONFIG_PPC32 */ +} + diff --git a/arch/powerpc/platforms/pseries/smp.c b/arch/powerpc/platforms/pseries/smp.c index 1a231c389ba0..1f8f6cfb94f7 100644 --- a/arch/powerpc/platforms/pseries/smp.c +++ b/arch/powerpc/platforms/pseries/smp.c @@ -35,7 +35,6 @@ #include #include #include -#include #include #include #include @@ -118,31 +117,6 @@ static void __devinit smp_xics_setup_cpu(int cpu) } #endif /* CONFIG_XICS */ -static DEFINE_SPINLOCK(timebase_lock); -static unsigned long timebase = 0; - -static void __devinit pSeries_give_timebase(void) -{ - spin_lock(&timebase_lock); - rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL); - timebase = get_tb(); - spin_unlock(&timebase_lock); - - while (timebase) - barrier(); - rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL); -} - -static void __devinit pSeries_take_timebase(void) -{ - while (!timebase) - barrier(); - spin_lock(&timebase_lock); - set_tb(timebase >> 32, timebase & 0xffffffff); - timebase = 0; - spin_unlock(&timebase_lock); -} - static void __devinit smp_pSeries_kick_cpu(int nr) { BUG_ON(nr < 0 || nr >= NR_CPUS); @@ -209,8 +183,8 @@ static void __init smp_init_pseries(void) /* Non-lpar has additional take/give timebase */ if (rtas_token("freeze-time-base") != RTAS_UNKNOWN_SERVICE) { - smp_ops->give_timebase = pSeries_give_timebase; - smp_ops->take_timebase = pSeries_take_timebase; + smp_ops->give_timebase = rtas_give_timebase; + smp_ops->take_timebase = rtas_take_timebase; } pr_debug(" <- smp_init_pSeries()\n"); diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c index 9c3af5045495..d46de1f0f3ee 100644 --- a/arch/powerpc/sysdev/mpic.c +++ b/arch/powerpc/sysdev/mpic.c @@ -279,28 +279,29 @@ static void _mpic_map_mmio(struct mpic *mpic, phys_addr_t phys_addr, } #ifdef CONFIG_PPC_DCR -static void _mpic_map_dcr(struct mpic *mpic, struct mpic_reg_bank *rb, +static void _mpic_map_dcr(struct mpic *mpic, struct device_node *node, + struct mpic_reg_bank *rb, unsigned int offset, unsigned int size) { const u32 *dbasep; - dbasep = of_get_property(mpic->irqhost->of_node, "dcr-reg", NULL); + dbasep = of_get_property(node, "dcr-reg", NULL); - rb->dhost = dcr_map(mpic->irqhost->of_node, *dbasep + offset, size); + rb->dhost = dcr_map(node, *dbasep + offset, size); BUG_ON(!DCR_MAP_OK(rb->dhost)); } -static inline void mpic_map(struct mpic *mpic, phys_addr_t phys_addr, - struct mpic_reg_bank *rb, unsigned int offset, - unsigned int size) +static inline void mpic_map(struct mpic *mpic, struct device_node *node, + phys_addr_t phys_addr, struct mpic_reg_bank *rb, + unsigned int offset, unsigned int size) { if (mpic->flags & MPIC_USES_DCR) - _mpic_map_dcr(mpic, rb, offset, size); + _mpic_map_dcr(mpic, node, rb, offset, size); else _mpic_map_mmio(mpic, phys_addr, rb, offset, size); } #else /* CONFIG_PPC_DCR */ -#define mpic_map(m,p,b,o,s) _mpic_map_mmio(m,p,b,o,s) +#define mpic_map(m,n,p,b,o,s) _mpic_map_mmio(m,p,b,o,s) #endif /* !CONFIG_PPC_DCR */ @@ -1052,11 +1053,10 @@ struct mpic * __init mpic_alloc(struct device_node *node, int intvec_top; u64 paddr = phys_addr; - mpic = alloc_bootmem(sizeof(struct mpic)); + mpic = kzalloc(sizeof(struct mpic), GFP_KERNEL); if (mpic == NULL) return NULL; - - memset(mpic, 0, sizeof(struct mpic)); + mpic->name = name; mpic->hc_irq = mpic_irq_chip; @@ -1152,8 +1152,8 @@ struct mpic * __init mpic_alloc(struct device_node *node, } /* Map the global registers */ - mpic_map(mpic, paddr, &mpic->gregs, MPIC_INFO(GREG_BASE), 0x1000); - mpic_map(mpic, paddr, &mpic->tmregs, MPIC_INFO(TIMER_BASE), 0x1000); + mpic_map(mpic, node, paddr, &mpic->gregs, MPIC_INFO(GREG_BASE), 0x1000); + mpic_map(mpic, node, paddr, &mpic->tmregs, MPIC_INFO(TIMER_BASE), 0x1000); /* Reset */ if (flags & MPIC_WANTS_RESET) { @@ -1194,7 +1194,7 @@ struct mpic * __init mpic_alloc(struct device_node *node, /* Map the per-CPU registers */ for (i = 0; i < mpic->num_cpus; i++) { - mpic_map(mpic, paddr, &mpic->cpuregs[i], + mpic_map(mpic, node, paddr, &mpic->cpuregs[i], MPIC_INFO(CPU_BASE) + i * MPIC_INFO(CPU_STRIDE), 0x1000); } @@ -1202,7 +1202,7 @@ struct mpic * __init mpic_alloc(struct device_node *node, /* Initialize main ISU if none provided */ if (mpic->isu_size == 0) { mpic->isu_size = mpic->num_sources; - mpic_map(mpic, paddr, &mpic->isus[0], + mpic_map(mpic, node, paddr, &mpic->isus[0], MPIC_INFO(IRQ_BASE), MPIC_INFO(IRQ_STRIDE) * mpic->isu_size); } mpic->isu_shift = 1 + __ilog2(mpic->isu_size - 1); @@ -1256,8 +1256,10 @@ void __init mpic_assign_isu(struct mpic *mpic, unsigned int isu_num, BUG_ON(isu_num >= MPIC_MAX_ISU); - mpic_map(mpic, paddr, &mpic->isus[isu_num], 0, + mpic_map(mpic, mpic->irqhost->of_node, + paddr, &mpic->isus[isu_num], 0, MPIC_INFO(IRQ_STRIDE) * mpic->isu_size); + if ((isu_first + mpic->isu_size) > mpic->num_sources) mpic->num_sources = isu_first + mpic->isu_size; } diff --git a/arch/powerpc/sysdev/qe_lib/qe.c b/arch/powerpc/sysdev/qe_lib/qe.c index b28b0e512d67..237e3654f48c 100644 --- a/arch/powerpc/sysdev/qe_lib/qe.c +++ b/arch/powerpc/sysdev/qe_lib/qe.c @@ -112,6 +112,7 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input) { unsigned long flags; u8 mcn_shift = 0, dev_shift = 0; + u32 ret; spin_lock_irqsave(&qe_lock, flags); if (cmd == QE_RESET) { @@ -139,11 +140,13 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input) } /* wait for the QE_CR_FLG to clear */ - while(in_be32(&qe_immr->cp.cecr) & QE_CR_FLG) - cpu_relax(); + ret = spin_event_timeout((in_be32(&qe_immr->cp.cecr) & QE_CR_FLG) == 0, + 100, 0); + /* On timeout (e.g. failure), the expression will be false (ret == 0), + otherwise it will be true (ret == 1). */ spin_unlock_irqrestore(&qe_lock, flags); - return 0; + return ret == 1; } EXPORT_SYMBOL(qe_issue_cmd); diff --git a/drivers/char/bsr.c b/drivers/char/bsr.c index 140ea10ecb88..c02db01f736e 100644 --- a/drivers/char/bsr.c +++ b/drivers/char/bsr.c @@ -27,6 +27,7 @@ #include #include #include +#include #include /* @@ -75,12 +76,13 @@ static struct class *bsr_class; static int bsr_major; enum { - BSR_8 = 0, - BSR_16 = 1, - BSR_64 = 2, - BSR_128 = 3, - BSR_UNKNOWN = 4, - BSR_MAX = 5, + BSR_8 = 0, + BSR_16 = 1, + BSR_64 = 2, + BSR_128 = 3, + BSR_4096 = 4, + BSR_UNKNOWN = 5, + BSR_MAX = 6, }; static unsigned bsr_types[BSR_MAX]; @@ -117,15 +119,22 @@ static int bsr_mmap(struct file *filp, struct vm_area_struct *vma) { unsigned long size = vma->vm_end - vma->vm_start; struct bsr_dev *dev = filp->private_data; + int ret; - if (size > dev->bsr_len || (size & (PAGE_SIZE-1))) - return -EINVAL; - - vma->vm_flags |= (VM_IO | VM_DONTEXPAND); vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); - if (io_remap_pfn_range(vma, vma->vm_start, dev->bsr_addr >> PAGE_SHIFT, - size, vma->vm_page_prot)) + /* check for the case of a small BSR device and map one 4k page for it*/ + if (dev->bsr_len < PAGE_SIZE && size == PAGE_SIZE) + ret = remap_4k_pfn(vma, vma->vm_start, dev->bsr_addr >> 12, + vma->vm_page_prot); + else if (size <= dev->bsr_len) + ret = io_remap_pfn_range(vma, vma->vm_start, + dev->bsr_addr >> PAGE_SHIFT, + size, vma->vm_page_prot); + else + return -EINVAL; + + if (ret) return -EAGAIN; return 0; @@ -205,6 +214,11 @@ static int bsr_add_node(struct device_node *bn) cur->bsr_stride = bsr_stride[i]; cur->bsr_dev = MKDEV(bsr_major, i + total_bsr_devs); + /* if we have a bsr_len of > 4k and less then PAGE_SIZE (64k pages) */ + /* we can only map 4k of it, so only advertise the 4k in sysfs */ + if (cur->bsr_len > 4096 && cur->bsr_len < PAGE_SIZE) + cur->bsr_len = 4096; + switch(cur->bsr_bytes) { case 8: cur->bsr_type = BSR_8; @@ -218,9 +232,11 @@ static int bsr_add_node(struct device_node *bn) case 128: cur->bsr_type = BSR_128; break; + case 4096: + cur->bsr_type = BSR_4096; + break; default: cur->bsr_type = BSR_UNKNOWN; - printk(KERN_INFO "unknown BSR size %d\n",cur->bsr_bytes); } cur->bsr_num = bsr_types[cur->bsr_type]; diff --git a/drivers/macintosh/macio_asic.c b/drivers/macintosh/macio_asic.c index 6e149f4a1fff..a0f68386c12f 100644 --- a/drivers/macintosh/macio_asic.c +++ b/drivers/macintosh/macio_asic.c @@ -378,6 +378,17 @@ static struct macio_dev * macio_add_one_device(struct macio_chip *chip, dev->ofdev.dev.bus = &macio_bus_type; dev->ofdev.dev.release = macio_release_dev; +#ifdef CONFIG_PCI + /* Set the DMA ops to the ones from the PCI device, this could be + * fishy if we didn't know that on PowerMac it's always direct ops + * or iommu ops that will work fine + */ + dev->ofdev.dev.archdata.dma_ops = + chip->lbus.pdev->dev.archdata.dma_ops; + dev->ofdev.dev.archdata.dma_data = + chip->lbus.pdev->dev.archdata.dma_data; +#endif /* CONFIG_PCI */ + #ifdef DEBUG printk("preparing mdev @%p, ofdev @%p, dev @%p, kobj @%p\n", dev, &dev->ofdev, &dev->ofdev.dev, &dev->ofdev.dev.kobj); diff --git a/drivers/watchdog/wdrtas.c b/drivers/watchdog/wdrtas.c index a4fe7a38d9b0..3bde56bce63a 100644 --- a/drivers/watchdog/wdrtas.c +++ b/drivers/watchdog/wdrtas.c @@ -218,16 +218,14 @@ static void wdrtas_timer_keepalive(void) */ static int wdrtas_get_temperature(void) { - long result; + int result; int temperature = 0; - result = rtas_call(wdrtas_token_get_sensor_state, 2, 2, - (void *)__pa(&temperature), - WDRTAS_THERMAL_SENSOR, 0); + result = rtas_get_sensor(WDRTAS_THERMAL_SENSOR, 0, &temperature); if (result < 0) printk(KERN_WARNING "wdrtas: reading the thermal sensor " - "faild: %li\n", result); + "failed: %i\n", result); else temperature = ((temperature * 9) / 5) + 32; /* fahrenheit */ diff --git a/scripts/dtc/.gitignore b/scripts/dtc/.gitignore new file mode 100644 index 000000000000..095acb49a374 --- /dev/null +++ b/scripts/dtc/.gitignore @@ -0,0 +1,5 @@ +dtc +dtc-lexer.lex.c +dtc-parser.tab.c +dtc-parser.tab.h +