forked from Minki/linux
at91: add support for RSIs EWS board
This adds support for the RSI EWS machine (at91rm9200-based), machine type 1609. Includes fixes as suggested by Uwe Kleine-König and cleanups as suggested by Russell and R.Schwebel. Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> [nicolas.ferre@atmel.com: simplify board file header, move to at91_init_irq_default] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit is contained in:
Josef Holzmayr
Nicolas Ferre
parent
ddf28352b8
commit
82cb865482
@ -182,6 +182,11 @@ config MACH_ECO920
|
||||
help
|
||||
Select this if you are using the eco920 board
|
||||
|
||||
config MACH_RSI_EWS
|
||||
bool "RSI Embedded Webserver"
|
||||
depends on ARCH_AT91RM9200
|
||||
help
|
||||
Select this if you are using RSIs EWS board.
|
||||
endif
|
||||
|
||||
# ----------------------------------------------------------
|
||||
|
||||
@ -36,6 +36,7 @@ obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o
|
||||
obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o
|
||||
obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o
|
||||
obj-$(CONFIG_MACH_ECO920) += board-eco920.o
|
||||
obj-$(CONFIG_MACH_RSI_EWS) += board-rsi-ews.o
|
||||
|
||||
# AT91SAM9260 board-specific support
|
||||
obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
|
||||
|
||||
233
arch/arm/mach-at91/board-rsi-ews.c
Normal file
233
arch/arm/mach-at91/board-rsi-ews.c
Normal file
@ -0,0 +1,233 @@
|
||||
/*
|
||||
* board-rsi-ews.c
|
||||
*
|
||||
* Copyright (C)
|
||||
* 2005 SAN People,
|
||||
* 2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
|
||||
*
|
||||
* Licensed under GPLv2 or later.
|
||||
*/
|
||||
|
||||
#include <linux/types.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/mm.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/mtd/physmap.h>
|
||||
|
||||
#include <asm/setup.h>
|
||||
#include <asm/mach-types.h>
|
||||
#include <asm/irq.h>
|
||||
|
||||
#include <asm/mach/arch.h>
|
||||
#include <asm/mach/map.h>
|
||||
#include <asm/mach/irq.h>
|
||||
|
||||
#include <mach/hardware.h>
|
||||
#include <mach/board.h>
|
||||
|
||||
#include <linux/gpio.h>
|
||||
|
||||
#include "generic.h"
|
||||
|
||||
static void __init rsi_ews_init_early(void)
|
||||
{
|
||||
/* Initialize processor: 18.432 MHz crystal */
|
||||
at91_initialize(18432000);
|
||||
|
||||
/* Setup the LEDs */
|
||||
at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
|
||||
|
||||
/* DBGU on ttyS0. (Rx & Tx only) */
|
||||
/* This one is for debugging */
|
||||
at91_register_uart(0, 0, 0);
|
||||
|
||||
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
||||
/* Dialin/-out modem interface */
|
||||
at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
|
||||
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
|
||||
| ATMEL_UART_RI);
|
||||
|
||||
/* USART3 on ttyS4. (Rx, Tx, RTS) */
|
||||
/* RS485 communication */
|
||||
at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
|
||||
|
||||
/* set serial console to ttyS0 (ie, DBGU) */
|
||||
at91_set_serial_console(0);
|
||||
}
|
||||
|
||||
/*
|
||||
* Ethernet
|
||||
*/
|
||||
static struct at91_eth_data rsi_ews_eth_data __initdata = {
|
||||
.phy_irq_pin = AT91_PIN_PC4,
|
||||
.is_rmii = 1,
|
||||
};
|
||||
|
||||
/*
|
||||
* USB Host
|
||||
*/
|
||||
static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
|
||||
.ports = 1,
|
||||
};
|
||||
|
||||
/*
|
||||
* SD/MC
|
||||
*/
|
||||
static struct at91_mmc_data rsi_ews_mmc_data __initdata = {
|
||||
.slot_b = 0,
|
||||
.wire4 = 1,
|
||||
.det_pin = AT91_PIN_PB27,
|
||||
.wp_pin = AT91_PIN_PB29,
|
||||
};
|
||||
|
||||
/*
|
||||
* I2C
|
||||
*/
|
||||
static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
|
||||
{
|
||||
I2C_BOARD_INFO("ds1337", 0x68),
|
||||
},
|
||||
{
|
||||
I2C_BOARD_INFO("24c01", 0x50),
|
||||
}
|
||||
};
|
||||
|
||||
/*
|
||||
* LEDs
|
||||
*/
|
||||
static struct gpio_led rsi_ews_leds[] = {
|
||||
{
|
||||
.name = "led0",
|
||||
.gpio = AT91_PIN_PB6,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "led1",
|
||||
.gpio = AT91_PIN_PB7,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "led2",
|
||||
.gpio = AT91_PIN_PB8,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "led3",
|
||||
.gpio = AT91_PIN_PB9,
|
||||
.active_low = 0,
|
||||
},
|
||||
};
|
||||
|
||||
/*
|
||||
* DataFlash
|
||||
*/
|
||||
static struct spi_board_info rsi_ews_spi_devices[] = {
|
||||
{ /* DataFlash chip 1*/
|
||||
.modalias = "mtd_dataflash",
|
||||
.chip_select = 0,
|
||||
.max_speed_hz = 5 * 1000 * 1000,
|
||||
},
|
||||
{ /* DataFlash chip 2*/
|
||||
.modalias = "mtd_dataflash",
|
||||
.chip_select = 1,
|
||||
.max_speed_hz = 5 * 1000 * 1000,
|
||||
},
|
||||
};
|
||||
|
||||
/*
|
||||
* NOR flash
|
||||
*/
|
||||
static struct mtd_partition rsiews_nor_partitions[] = {
|
||||
{
|
||||
.name = "boot",
|
||||
.offset = 0,
|
||||
.size = 3 * SZ_128K,
|
||||
.mask_flags = MTD_WRITEABLE
|
||||
},
|
||||
{
|
||||
.name = "kernel",
|
||||
.offset = MTDPART_OFS_NXTBLK,
|
||||
.size = SZ_2M - (3 * SZ_128K)
|
||||
},
|
||||
{
|
||||
.name = "root",
|
||||
.offset = MTDPART_OFS_NXTBLK,
|
||||
.size = SZ_8M
|
||||
},
|
||||
{
|
||||
.name = "kernelupd",
|
||||
.offset = MTDPART_OFS_NXTBLK,
|
||||
.size = 3 * SZ_512K,
|
||||
.mask_flags = MTD_WRITEABLE
|
||||
},
|
||||
{
|
||||
.name = "rootupd",
|
||||
.offset = MTDPART_OFS_NXTBLK,
|
||||
.size = 9 * SZ_512K,
|
||||
.mask_flags = MTD_WRITEABLE
|
||||
},
|
||||
};
|
||||
|
||||
static struct physmap_flash_data rsiews_nor_data = {
|
||||
.width = 2,
|
||||
.parts = rsiews_nor_partitions,
|
||||
.nr_parts = ARRAY_SIZE(rsiews_nor_partitions),
|
||||
};
|
||||
|
||||
#define NOR_BASE AT91_CHIPSELECT_0
|
||||
#define NOR_SIZE SZ_16M
|
||||
|
||||
static struct resource nor_flash_resources[] = {
|
||||
{
|
||||
.start = NOR_BASE,
|
||||
.end = NOR_BASE + NOR_SIZE - 1,
|
||||
.flags = IORESOURCE_MEM,
|
||||
}
|
||||
};
|
||||
|
||||
static struct platform_device rsiews_nor_flash = {
|
||||
.name = "physmap-flash",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &rsiews_nor_data,
|
||||
},
|
||||
.resource = nor_flash_resources,
|
||||
.num_resources = ARRAY_SIZE(nor_flash_resources),
|
||||
};
|
||||
|
||||
/*
|
||||
* Init Func
|
||||
*/
|
||||
static void __init rsi_ews_board_init(void)
|
||||
{
|
||||
/* Serial */
|
||||
at91_add_device_serial();
|
||||
at91_set_gpio_output(AT91_PIN_PA21, 0);
|
||||
/* Ethernet */
|
||||
at91_add_device_eth(&rsi_ews_eth_data);
|
||||
/* USB Host */
|
||||
at91_add_device_usbh(&rsi_ews_usbh_data);
|
||||
/* I2C */
|
||||
at91_add_device_i2c(rsi_ews_i2c_devices,
|
||||
ARRAY_SIZE(rsi_ews_i2c_devices));
|
||||
/* SPI */
|
||||
at91_add_device_spi(rsi_ews_spi_devices,
|
||||
ARRAY_SIZE(rsi_ews_spi_devices));
|
||||
/* MMC */
|
||||
at91_add_device_mmc(0, &rsi_ews_mmc_data);
|
||||
/* NOR Flash */
|
||||
platform_device_register(&rsiews_nor_flash);
|
||||
/* LEDs */
|
||||
at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
|
||||
}
|
||||
|
||||
MACHINE_START(RSI_EWS, "RSI EWS")
|
||||
/* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */
|
||||
.timer = &at91rm9200_timer,
|
||||
.map_io = at91_map_io,
|
||||
.init_early = rsi_ews_init_early,
|
||||
.init_irq = at91_init_irq_default,
|
||||
.init_machine = rsi_ews_board_init,
|
||||
MACHINE_END
|
||||
Loading…
Reference in New Issue
Block a user