leandrof/linux
1
0
Fork 0
forked from Minki/linux
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6

Browse Source
This commit is contained in:
David S. Miller 2009-12-29 19:44:25 -08:00
commit 7f9d3577e2
29 changed files with 129 additions and 447 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

18
drivers/net/wireless/ath/ath5k/base.c
View File

@ -1903,17 +1903,6 @@ accept:
rxs->noise = sc->ah->ah_noise_floor;
rxs->signal = rxs->noise + rs.rs_rssi;
/* An rssi of 35 indicates you should be able use
* 54 Mbps reliably. A more elaborate scheme can be used
* here but it requires a map of SNR/throughput for each
* possible mode used */
rxs->qual = rs.rs_rssi * 100 / 35;
/* rssi can be more than 35 though, anything above that
* should be considered at 100% */
if (rxs->qual > 100)
rxs->qual = 100;
rxs->antenna = rs.rs_antenna;
rxs->rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate);
rxs->flag |= ath5k_rx_decrypted(sc, ds, skb, &rs);
@ -2381,6 +2370,9 @@ ath5k_init(struct ath5k_softc *sc)
*/
ath5k_stop_locked(sc);
/* Set PHY calibration interval */
ah->ah_cal_intval = ath5k_calinterval;
/*
* The basic interface to setting the hardware in a good
* state is ``reset''. On return the hardware is known to
@ -2408,10 +2400,6 @@ ath5k_init(struct ath5k_softc *sc)
/* Set ack to be sent at low bit-rates */
ath5k_hw_set_ack_bitrate_high(ah, false);
/* Set PHY calibration inteval */
ah->ah_cal_intval = ath5k_calinterval;
ret = 0;
done:
mmiowb();

3
drivers/net/wireless/ath/ath9k/mac.h
View File

@ -77,6 +77,9 @@
#define ATH9K_TXERR_XTXOP 0x08
#define ATH9K_TXERR_TIMER_EXPIRED 0x10
#define ATH9K_TX_ACKED 0x20
#define ATH9K_TXERR_MASK \
(ATH9K_TXERR_XRETRY | ATH9K_TXERR_FILT | ATH9K_TXERR_FIFO | \
ATH9K_TXERR_XTXOP | ATH9K_TXERR_TIMER_EXPIRED)
#define ATH9K_TX_BA 0x01
#define ATH9K_TX_PWRMGMT 0x02

14
drivers/net/wireless/ath/ath9k/main.c
View File

@ -2514,6 +2514,9 @@ static void ath9k_stop(struct ieee80211_hw *hw)
return; /* another wiphy still in use */
}
/* Ensure HW is awake when we try to shut it down. */
ath9k_ps_wakeup(sc);
if (ah->btcoex_hw.enabled) {
ath9k_hw_btcoex_disable(ah);
if (ah->btcoex_hw.scheme == ATH_BTCOEX_CFG_3WIRE)
@ -2534,6 +2537,9 @@ static void ath9k_stop(struct ieee80211_hw *hw)
/* disable HAL and put h/w to sleep */
ath9k_hw_disable(ah);
ath9k_hw_configpcipowersave(ah, 1, 1);
ath9k_ps_restore(sc);
/* Finally, put the chip in FULL SLEEP mode */
ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP);
sc->sc_flags |= SC_OP_INVALID;
@ -2647,8 +2653,10 @@ static void ath9k_remove_interface(struct ieee80211_hw *hw,
if ((sc->sc_ah->opmode == NL80211_IFTYPE_AP) ||
(sc->sc_ah->opmode == NL80211_IFTYPE_ADHOC) ||
(sc->sc_ah->opmode == NL80211_IFTYPE_MESH_POINT)) {
ath9k_ps_wakeup(sc);
ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq);
ath_beacon_return(sc, avp);
ath9k_ps_restore(sc);
}
sc->sc_flags &= ~SC_OP_BEACONS;
@ -3097,15 +3105,21 @@ static int ath9k_ampdu_action(struct ieee80211_hw *hw,
case IEEE80211_AMPDU_RX_STOP:
break;
case IEEE80211_AMPDU_TX_START:
ath9k_ps_wakeup(sc);
ath_tx_aggr_start(sc, sta, tid, ssn);
ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_STOP:
ath9k_ps_wakeup(sc);
ath_tx_aggr_stop(sc, sta, tid);
ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_OPERATIONAL:
ath9k_ps_wakeup(sc);
ath_tx_aggr_resume(sc, sta, tid);
ath9k_ps_restore(sc);
break;
default:
ath_print(ath9k_hw_common(sc->sc_ah), ATH_DBG_FATAL,

2
drivers/net/wireless/ath/ath9k/pci.c
View File

@ -96,7 +96,7 @@ static void ath_pci_bt_coex_prep(struct ath_common *common)
pci_write_config_byte(pdev, ATH_PCIE_CAP_LINK_CTRL, aspm);
}
const static struct ath_bus_ops ath_pci_bus_ops = {
static const struct ath_bus_ops ath_pci_bus_ops = {
.read_cachesize = ath_pci_read_cachesize,
.cleanup = ath_pci_cleanup,
.eeprom_read = ath_pci_eeprom_read,

2
drivers/net/wireless/ath/ath9k/xmit.c
View File

@ -2072,7 +2072,7 @@ static void ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq)
&txq->axq_q, lastbf->list.prev);
txq->axq_depth--;
txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_FILT);
txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_MASK);
txq->axq_tx_inprogress = false;
spin_unlock_bh(&txq->axq_lock);

195
drivers/net/wireless/b43/dma.c
View File

@ -383,160 +383,44 @@ static inline
}
}
/* Check if a DMA region fits the device constraints.
* Returns true, if the region is OK for usage with this device. */
static inline bool b43_dma_address_ok(struct b43_dmaring *ring,
dma_addr_t addr, size_t size)
{
switch (ring->type) {
case B43_DMA_30BIT:
if ((u64)addr + size > (1ULL << 30))
return 0;
break;
case B43_DMA_32BIT:
if ((u64)addr + size > (1ULL << 32))
return 0;
break;
case B43_DMA_64BIT:
/* Currently we can't have addresses beyond
* 64bit in the kernel. */
break;
}
return 1;
}
#define is_4k_aligned(addr) (((u64)(addr) & 0x0FFFull) == 0)
#define is_8k_aligned(addr) (((u64)(addr) & 0x1FFFull) == 0)
static void b43_unmap_and_free_ringmem(struct b43_dmaring *ring, void *base,
dma_addr_t dmaaddr, size_t size)
{
ssb_dma_unmap_single(ring->dev->dev, dmaaddr, size, DMA_TO_DEVICE);
free_pages((unsigned long)base, get_order(size));
}
static void * __b43_get_and_map_ringmem(struct b43_dmaring *ring,
dma_addr_t *dmaaddr, size_t size,
gfp_t gfp_flags)
{
void *base;
base = (void *)__get_free_pages(gfp_flags, get_order(size));
if (!base)
return NULL;
memset(base, 0, size);
*dmaaddr = ssb_dma_map_single(ring->dev->dev, base, size,
DMA_TO_DEVICE);
if (ssb_dma_mapping_error(ring->dev->dev, *dmaaddr)) {
free_pages((unsigned long)base, get_order(size));
return NULL;
}
return base;
}
static void * b43_get_and_map_ringmem(struct b43_dmaring *ring,
dma_addr_t *dmaaddr, size_t size)
{
void *base;
base = __b43_get_and_map_ringmem(ring, dmaaddr, size,
GFP_KERNEL);
if (!base) {
b43err(ring->dev->wl, "Failed to allocate or map pages "
"for DMA ringmemory\n");
return NULL;
}
if (!b43_dma_address_ok(ring, *dmaaddr, size)) {
/* The memory does not fit our device constraints.
* Retry with GFP_DMA set to get lower memory. */
b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
base = __b43_get_and_map_ringmem(ring, dmaaddr, size,
GFP_KERNEL | GFP_DMA);
if (!base) {
b43err(ring->dev->wl, "Failed to allocate or map pages "
"in the GFP_DMA region for DMA ringmemory\n");
return NULL;
}
if (!b43_dma_address_ok(ring, *dmaaddr, size)) {
b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
b43err(ring->dev->wl, "Failed to allocate DMA "
"ringmemory that fits device constraints\n");
return NULL;
}
}
/* We expect the memory to be 4k aligned, at least. */
if (B43_WARN_ON(!is_4k_aligned(*dmaaddr))) {
b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size);
return NULL;
}
return base;
}
static int alloc_ringmemory(struct b43_dmaring *ring)
{
unsigned int required;
void *base;
dma_addr_t dmaaddr;
gfp_t flags = GFP_KERNEL;
/* There are several requirements to the descriptor ring memory:
* - The memory region needs to fit the address constraints for the
* device (same as for frame buffers).
* - For 30/32bit DMA devices, the descriptor ring must be 4k aligned.
* - For 64bit DMA devices, the descriptor ring must be 8k aligned.
/* The specs call for 4K buffers for 30- and 32-bit DMA with 4K
* alignment and 8K buffers for 64-bit DMA with 8K alignment. Testing
* has shown that 4K is sufficient for the latter as long as the buffer
* does not cross an 8K boundary.
*
* For unknown reasons - possibly a hardware error - the BCM4311 rev
* 02, which uses 64-bit DMA, needs the ring buffer in very low memory,
* which accounts for the GFP_DMA flag below.
*
* The flags here must match the flags in free_ringmemory below!
*/
if (ring->type == B43_DMA_64BIT)
required = ring->nr_slots * sizeof(struct b43_dmadesc64);
else
required = ring->nr_slots * sizeof(struct b43_dmadesc32);
if (B43_WARN_ON(required > 0x1000))
flags |= GFP_DMA;
ring->descbase = ssb_dma_alloc_consistent(ring->dev->dev,
B43_DMA_RINGMEMSIZE,
&(ring->dmabase), flags);
if (!ring->descbase) {
b43err(ring->dev->wl, "DMA ringmemory allocation failed\n");
return -ENOMEM;
ring->alloc_descsize = 0x1000;
base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize);
if (!base)
return -ENOMEM;
ring->alloc_descbase = base;
ring->alloc_dmabase = dmaaddr;
if ((ring->type != B43_DMA_64BIT) || is_8k_aligned(dmaaddr)) {
/* We're on <=32bit DMA, or we already got 8k aligned memory.
* That's all we need, so we're fine. */
ring->descbase = base;
ring->dmabase = dmaaddr;
return 0;
}
b43_unmap_and_free_ringmem(ring, base, dmaaddr, ring->alloc_descsize);
/* Ok, we failed at the 8k alignment requirement.
* Try to force-align the memory region now. */
ring->alloc_descsize = 0x2000;
base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize);
if (!base)
return -ENOMEM;
ring->alloc_descbase = base;
ring->alloc_dmabase = dmaaddr;
if (is_8k_aligned(dmaaddr)) {
/* We're already 8k aligned. That Ok, too. */
ring->descbase = base;
ring->dmabase = dmaaddr;
return 0;
}
/* Force-align it to 8k */
ring->descbase = (void *)((u8 *)base + 0x1000);
ring->dmabase = dmaaddr + 0x1000;
B43_WARN_ON(!is_8k_aligned(ring->dmabase));
memset(ring->descbase, 0, B43_DMA_RINGMEMSIZE);
return 0;
}
static void free_ringmemory(struct b43_dmaring *ring)
{
b43_unmap_and_free_ringmem(ring, ring->alloc_descbase,
ring->alloc_dmabase, ring->alloc_descsize);
gfp_t flags = GFP_KERNEL;
if (ring->type == B43_DMA_64BIT)
flags |= GFP_DMA;
ssb_dma_free_consistent(ring->dev->dev, B43_DMA_RINGMEMSIZE,
ring->descbase, ring->dmabase, flags);
}
/* Reset the RX DMA channel */
@ -646,14 +530,29 @@ static bool b43_dma_mapping_error(struct b43_dmaring *ring,
if (unlikely(ssb_dma_mapping_error(ring->dev->dev, addr)))
return 1;
if (!b43_dma_address_ok(ring, addr, buffersize)) {
/* We can't support this address. Unmap it again. */
unmap_descbuffer(ring, addr, buffersize, dma_to_device);
return 1;
switch (ring->type) {
case B43_DMA_30BIT:
if ((u64)addr + buffersize > (1ULL << 30))
goto address_error;
break;
case B43_DMA_32BIT:
if ((u64)addr + buffersize > (1ULL << 32))
goto address_error;
break;
case B43_DMA_64BIT:
/* Currently we can't have addresses beyond
* 64bit in the kernel. */
break;
}
/* The address is OK. */
return 0;
address_error:
/* We can't support this address. Unmap it again. */
unmap_descbuffer(ring, addr, buffersize, dma_to_device);
return 1;
}
static bool b43_rx_buffer_is_poisoned(struct b43_dmaring *ring, struct sk_buff *skb)
@ -715,9 +614,6 @@ static int setup_rx_descbuffer(struct b43_dmaring *ring,
meta->dmaaddr = dmaaddr;
ring->ops->fill_descriptor(ring, desc, dmaaddr,
ring->rx_buffersize, 0, 0, 0);
ssb_dma_sync_single_for_device(ring->dev->dev,
ring->alloc_dmabase,
ring->alloc_descsize, DMA_TO_DEVICE);
return 0;
}
@ -1354,9 +1250,6 @@ static int dma_tx_fragment(struct b43_dmaring *ring,
}
/* Now transfer the whole frame. */
wmb();
ssb_dma_sync_single_for_device(ring->dev->dev,
ring->alloc_dmabase,
ring->alloc_descsize, DMA_TO_DEVICE);
ops->poke_tx(ring, next_slot(ring, slot));
return 0;

7
drivers/net/wireless/b43/dma.h
View File

@ -157,6 +157,7 @@ struct b43_dmadesc_generic {
} __attribute__ ((__packed__));
/* Misc DMA constants */
#define B43_DMA_RINGMEMSIZE PAGE_SIZE
#define B43_DMA0_RX_FRAMEOFFSET 30
/* DMA engine tuning knobs */
@ -246,12 +247,6 @@ struct b43_dmaring {
/* The QOS priority assigned to this ring. Only used for TX rings.
* This is the mac80211 "queue" value. */
u8 queue_prio;
/* Pointers and size of the originally allocated and mapped memory
* region for the descriptor ring. */
void *alloc_descbase;
dma_addr_t alloc_dmabase;
unsigned int alloc_descsize;
/* Pointer to our wireless device. */
struct b43_wldev *dev;
#ifdef CONFIG_B43_DEBUG
/* Maximum number of used slots. */

10
drivers/net/wireless/iwlwifi/iwl-3945.c
View File

@ -681,19 +681,13 @@ static void iwl3945_rx_reply_rx(struct iwl_priv *priv,
snr = rx_stats_sig_avg / rx_stats_noise_diff;
rx_status.noise = rx_status.signal -
iwl3945_calc_db_from_ratio(snr);
rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal,
rx_status.noise);
/* If noise info not available, calculate signal quality indicator (%)
* using just the dBm signal level. */
} else {
rx_status.noise = priv->last_rx_noise;
rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, 0);
}
IWL_DEBUG_STATS(priv, "Rssi %d noise %d qual %d sig_avg %d noise_diff %d\n",
rx_status.signal, rx_status.noise, rx_status.qual,
IWL_DEBUG_STATS(priv, "Rssi %d noise %d sig_avg %d noise_diff %d\n",
rx_status.signal, rx_status.noise,
rx_stats_sig_avg, rx_stats_noise_diff);
header = (struct ieee80211_hdr *)IWL_RX_DATA(pkt);

1
drivers/net/wireless/iwlwifi/iwl-3945.h
View File

@ -222,7 +222,6 @@ struct iwl3945_ibss_seq {
*
*****************************************************************************/
extern int iwl3945_calc_db_from_ratio(int sig_ratio);
extern int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm);
extern void iwl3945_rx_replenish(void *data);
extern void iwl3945_rx_queue_reset(struct iwl_priv *priv, struct iwl_rx_queue *rxq);
extern unsigned int iwl3945_fill_beacon_frame(struct iwl_priv *priv,

2
drivers/net/wireless/iwlwifi/iwl-agn-rs.c
View File

@ -150,7 +150,7 @@ static s32 expected_tpt_mimo3_40MHz[4][IWL_RATE_COUNT] = {
};
/* mbps, mcs */
const static struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = {
static const struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = {
{ "1", "BPSK DSSS"},
{ "2", "QPSK DSSS"},
{"5.5", "BPSK CCK"},

48
drivers/net/wireless/iwlwifi/iwl-rx.c
View File

@ -650,47 +650,6 @@ void iwl_reply_statistics(struct iwl_priv *priv,
}
EXPORT_SYMBOL(iwl_reply_statistics);
#define PERFECT_RSSI (-20) /* dBm */
#define WORST_RSSI (-95) /* dBm */
#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI)
/* Calculate an indication of rx signal quality (a percentage, not dBm!).
* See http://www.ces.clemson.edu/linux/signal_quality.shtml for info
* about formulas used below. */
static int iwl_calc_sig_qual(int rssi_dbm, int noise_dbm)
{
int sig_qual;
int degradation = PERFECT_RSSI - rssi_dbm;
/* If we get a noise measurement, use signal-to-noise ratio (SNR)
* as indicator; formula is (signal dbm - noise dbm).
* SNR at or above 40 is a great signal (100%).
* Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator.
* Weakest usable signal is usually 10 - 15 dB SNR. */
if (noise_dbm) {
if (rssi_dbm - noise_dbm >= 40)
return 100;
else if (rssi_dbm < noise_dbm)
return 0;
sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2;
/* Else use just the signal level.
* This formula is a least squares fit of data points collected and
* compared with a reference system that had a percentage (%) display
* for signal quality. */
} else
sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation *
(15 * RSSI_RANGE + 62 * degradation)) /
(RSSI_RANGE * RSSI_RANGE);
if (sig_qual > 100)
sig_qual = 100;
else if (sig_qual < 1)
sig_qual = 0;
return sig_qual;
}
/* Calc max signal level (dBm) among 3 possible receivers */
static inline int iwl_calc_rssi(struct iwl_priv *priv,
struct iwl_rx_phy_res *rx_resp)
@ -1101,11 +1060,8 @@ void iwl_rx_reply_rx(struct iwl_priv *priv,
if (iwl_is_associated(priv) &&
!test_bit(STATUS_SCANNING, &priv->status)) {
rx_status.noise = priv->last_rx_noise;
rx_status.qual = iwl_calc_sig_qual(rx_status.signal,
rx_status.noise);
} else {
rx_status.noise = IWL_NOISE_MEAS_NOT_AVAILABLE;
rx_status.qual = iwl_calc_sig_qual(rx_status.signal, 0);
}
/* Reset beacon noise level if not associated. */
@ -1118,8 +1074,8 @@ void iwl_rx_reply_rx(struct iwl_priv *priv,
iwl_dbg_report_frame(priv, phy_res, len, header, 1);
#endif
iwl_dbg_log_rx_data_frame(priv, len, header);
IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, qual %d, TSF %llu\n",
rx_status.signal, rx_status.noise, rx_status.qual,
IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, TSF %llu\n",
rx_status.signal, rx_status.noise,
(unsigned long long)rx_status.mactime);
/*

41
drivers/net/wireless/iwlwifi/iwl3945-base.c
View File

@ -1299,47 +1299,6 @@ int iwl3945_calc_db_from_ratio(int sig_ratio)
return (int)ratio2dB[sig_ratio];
}
#define PERFECT_RSSI (-20) /* dBm */
#define WORST_RSSI (-95) /* dBm */
#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI)
/* Calculate an indication of rx signal quality (a percentage, not dBm!).
* See http://www.ces.clemson.edu/linux/signal_quality.shtml for info
* about formulas used below. */
int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm)
{
int sig_qual;
int degradation = PERFECT_RSSI - rssi_dbm;
/* If we get a noise measurement, use signal-to-noise ratio (SNR)
* as indicator; formula is (signal dbm - noise dbm).
* SNR at or above 40 is a great signal (100%).
* Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator.
* Weakest usable signal is usually 10 - 15 dB SNR. */
if (noise_dbm) {
if (rssi_dbm - noise_dbm >= 40)
return 100;
else if (rssi_dbm < noise_dbm)
return 0;
sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2;
/* Else use just the signal level.
* This formula is a least squares fit of data points collected and
* compared with a reference system that had a percentage (%) display
* for signal quality. */
} else
sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation *
(15 * RSSI_RANGE + 62 * degradation)) /
(RSSI_RANGE * RSSI_RANGE);
if (sig_qual > 100)
sig_qual = 100;
else if (sig_qual < 1)
sig_qual = 0;
return sig_qual;
}
/**
* iwl3945_rx_handle - Main entry function for receiving responses from uCode
*

2
drivers/net/wireless/iwmc3200wifi/iwm.h
View File

@ -268,7 +268,7 @@ struct iwm_priv {
struct sk_buff_head rx_list;
struct list_head rx_tickets;
struct list_head rx_packets[IWM_RX_ID_HASH];
struct list_head rx_packets[IWM_RX_ID_HASH + 1];
struct workqueue_struct *rx_wq;
struct work_struct rx_worker;

22
drivers/net/wireless/libertas/scan.c
View File

@ -567,11 +567,8 @@ int lbs_scan_networks(struct lbs_private *priv, int full_scan)
chan_count = lbs_scan_create_channel_list(priv, chan_list);
netif_stop_queue(priv->dev);
netif_carrier_off(priv->dev);
if (priv->mesh_dev) {
if (priv->mesh_dev)
netif_stop_queue(priv->mesh_dev);
netif_carrier_off(priv->mesh_dev);
}
/* Prepare to continue an interrupted scan */
lbs_deb_scan("chan_count %d, scan_channel %d\n",
@ -635,16 +632,13 @@ out2:
priv->scan_channel = 0;
out:
if (priv->connect_status == LBS_CONNECTED) {
netif_carrier_on(priv->dev);
if (!priv->tx_pending_len)
netif_wake_queue(priv->dev);
}
if (priv->mesh_dev && (priv->mesh_connect_status == LBS_CONNECTED)) {
netif_carrier_on(priv->mesh_dev);
if (!priv->tx_pending_len)
netif_wake_queue(priv->mesh_dev);
}
if (priv->connect_status == LBS_CONNECTED && !priv->tx_pending_len)
netif_wake_queue(priv->dev);
if (priv->mesh_dev && (priv->mesh_connect_status == LBS_CONNECTED) &&
!priv->tx_pending_len)
netif_wake_queue(priv->mesh_dev);
kfree(chan_list);
lbs_deb_leave_args(LBS_DEB_SCAN, "ret %d", ret);

1
drivers/net/wireless/libertas_tf/main.c
View File

@ -495,7 +495,6 @@ int lbtf_rx(struct lbtf_private *priv, struct sk_buff *skb)
stats.band = IEEE80211_BAND_2GHZ;
stats.signal = prxpd->snr;
stats.noise = prxpd->nf;
stats.qual = prxpd->snr - prxpd->nf;
/* Marvell rate index has a hole at value 4 */
if (prxpd->rx_rate > 4)
--prxpd->rx_rate;

6
drivers/net/wireless/orinoco/wext.c
View File

@ -23,7 +23,7 @@
#define MAX_RID_LEN 1024
/* Helper routine to record keys
* Do not call from interrupt context */
* It is called under orinoco_lock so it may not sleep */
static int orinoco_set_key(struct orinoco_private *priv, int index,
enum orinoco_alg alg, const u8 *key, int key_len,
const u8 *seq, int seq_len)
@ -32,14 +32,14 @@ static int orinoco_set_key(struct orinoco_private *priv, int index,
kzfree(priv->keys[index].seq);
if (key_len) {
priv->keys[index].key = kzalloc(key_len, GFP_KERNEL);
priv->keys[index].key = kzalloc(key_len, GFP_ATOMIC);
if (!priv->keys[index].key)
goto nomem;
} else
priv->keys[index].key = NULL;
if (seq_len) {
priv->keys[index].seq = kzalloc(seq_len, GFP_KERNEL);
priv->keys[index].seq = kzalloc(seq_len, GFP_ATOMIC);
if (!priv->keys[index].seq)
goto free_key;
} else

1
drivers/net/wireless/rt2x00/rt2800usb.c
View File

@ -922,6 +922,7 @@ static struct usb_device_id rt2800usb_device_table[] = {
{ USB_DEVICE(0x1737, 0x0070), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x1737, 0x0071), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x1737, 0x0077), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x1737, 0x0079), USB_DEVICE_DATA(&rt2800usb_ops) },
/* Logitec */
{ USB_DEVICE(0x0789, 0x0162), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x0789, 0x0163), USB_DEVICE_DATA(&rt2800usb_ops) },

1
drivers/net/wireless/rtl818x/rtl8180_dev.c
View File

@ -132,7 +132,6 @@ static void rtl8180_handle_rx(struct ieee80211_hw *dev)
rx_status.antenna = (flags2 >> 15) & 1;
/* TODO: improve signal/rssi reporting */
rx_status.qual = flags2 & 0xFF;
rx_status.signal = (flags2 >> 8) & 0x7F;
/* XXX: is this correct? */
rx_status.rate_idx = (flags >> 20) & 0xF;

2
drivers/net/wireless/wl12xx/wl1251_boot.c
View File

@ -256,7 +256,7 @@ int wl1251_boot_run_firmware(struct wl1251 *wl)
}
}
if (loop >= INIT_LOOP) {
if (loop > INIT_LOOP) {
wl1251_error("timeout waiting for the hardware to "
"complete initialization");
return -EIO;

4
drivers/net/wireless/wl12xx/wl1271_cmd.c
View File

@ -777,7 +777,7 @@ out:
return ret;
}
static int wl1271_build_basic_rates(char *rates, u8 band)
static int wl1271_build_basic_rates(u8 *rates, u8 band)
{
u8 index = 0;
@ -804,7 +804,7 @@ static int wl1271_build_basic_rates(char *rates, u8 band)
return index;
}
static int wl1271_build_extended_rates(char *rates, u8 band)
static int wl1271_build_extended_rates(u8 *rates, u8 band)
{
u8 index = 0;

140
drivers/net/wireless/zd1211rw/zd_chip.c
View File

@ -1325,151 +1325,11 @@ int zd_chip_set_basic_rates(struct zd_chip *chip, u16 cr_rates)
return r;
}
static int ofdm_qual_db(u8 status_quality, u8 zd_rate, unsigned int size)
{
static const u16 constants[] = {
715, 655, 585, 540, 470, 410, 360, 315,
270, 235, 205, 175, 150, 125, 105, 85,
65, 50, 40, 25, 15
};
int i;
u32 x;
/* It seems that their quality parameter is somehow per signal
* and is now transferred per bit.
*/
switch (zd_rate) {
case ZD_OFDM_RATE_6M:
case ZD_OFDM_RATE_12M:
case ZD_OFDM_RATE_24M:
size *= 2;
break;
case ZD_OFDM_RATE_9M:
case ZD_OFDM_RATE_18M:
case ZD_OFDM_RATE_36M:
case ZD_OFDM_RATE_54M:
size *= 4;
size /= 3;
break;
case ZD_OFDM_RATE_48M:
size *= 3;
size /= 2;
break;
default:
return -EINVAL;
}
x = (10000 * status_quality)/size;
for (i = 0; i < ARRAY_SIZE(constants); i++) {
if (x > constants[i])
break;
}
switch (zd_rate) {
case ZD_OFDM_RATE_6M:
case ZD_OFDM_RATE_9M:
i += 3;
break;
case ZD_OFDM_RATE_12M:
case ZD_OFDM_RATE_18M:
i += 5;
break;
case ZD_OFDM_RATE_24M:
case ZD_OFDM_RATE_36M:
i += 9;
break;
case ZD_OFDM_RATE_48M:
case ZD_OFDM_RATE_54M:
i += 15;
break;
default:
return -EINVAL;
}
return i;
}
static int ofdm_qual_percent(u8 status_quality, u8 zd_rate, unsigned int size)
{
int r;
r = ofdm_qual_db(status_quality, zd_rate, size);
ZD_ASSERT(r >= 0);
if (r < 0)
r = 0;
r = (r * 100)/29;
return r <= 100 ? r : 100;
}
static unsigned int log10times100(unsigned int x)
{
static const u8 log10[] = {
0,
0, 30, 47, 60, 69, 77, 84, 90, 95, 100,
104, 107, 111, 114, 117, 120, 123, 125, 127, 130,
132, 134, 136, 138, 139, 141, 143, 144, 146, 147,
149, 150, 151, 153, 154, 155, 156, 157, 159, 160,
161, 162, 163, 164, 165, 166, 167, 168, 169, 169,
170, 171, 172, 173, 174, 174, 175, 176, 177, 177,
178, 179, 179, 180, 181, 181, 182, 183, 183, 184,
185, 185, 186, 186, 187, 188, 188, 189, 189, 190,
190, 191, 191, 192, 192, 193, 193, 194, 194, 195,
195, 196, 196, 197, 197, 198, 198, 199, 199, 200,
200, 200, 201, 201, 202, 202, 202, 203, 203, 204,
204, 204, 205, 205, 206, 206, 206, 207, 207, 207,
208, 208, 208, 209, 209, 210, 210, 210, 211, 211,
211, 212, 212, 212, 213, 213, 213, 213, 214, 214,
214, 215, 215, 215, 216, 216, 216, 217, 217, 217,
217, 218, 218, 218, 219, 219, 219, 219, 220, 220,
220, 220, 221, 221, 221, 222, 222, 222, 222, 223,
223, 223, 223, 224, 224, 224, 224,
};
return x < ARRAY_SIZE(log10) ? log10[x] : 225;
}
enum {
MAX_CCK_EVM_DB = 45,
};
static int cck_evm_db(u8 status_quality)
{
return (20 * log10times100(status_quality)) / 100;
}
static int cck_snr_db(u8 status_quality)
{
int r = MAX_CCK_EVM_DB - cck_evm_db(status_quality);
ZD_ASSERT(r >= 0);
return r;
}
static int cck_qual_percent(u8 status_quality)
{
int r;
r = cck_snr_db(status_quality);
r = (100*r)/17;
return r <= 100 ? r : 100;
}
static inline u8 zd_rate_from_ofdm_plcp_header(const void *rx_frame)
{
return ZD_OFDM | zd_ofdm_plcp_header_rate(rx_frame);
}
u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size,
const struct rx_status *status)
{
return (status->frame_status&ZD_RX_OFDM) ?
ofdm_qual_percent(status->signal_quality_ofdm,
zd_rate_from_ofdm_plcp_header(rx_frame),
size) :
cck_qual_percent(status->signal_quality_cck);
}
/**
* zd_rx_rate - report zd-rate
* @rx_frame - received frame

3
drivers/net/wireless/zd1211rw/zd_chip.h
View File

@ -929,9 +929,6 @@ static inline int zd_get_beacon_interval(struct zd_chip *chip, u32 *interval)
struct rx_status;
u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size,
const struct rx_status *status);
u8 zd_rx_rate(const void *rx_frame, const struct rx_status *status);
struct zd_mc_hash {

3
drivers/net/wireless/zd1211rw/zd_mac.c
View File

@ -828,9 +828,6 @@ int zd_mac_rx(struct ieee80211_hw *hw, const u8 *buffer, unsigned int length)
stats.freq = zd_channels[_zd_chip_get_channel(&mac->chip) - 1].center_freq;
stats.band = IEEE80211_BAND_2GHZ;
stats.signal = status->signal_strength;
stats.qual = zd_rx_qual_percent(buffer,
length - sizeof(struct rx_status),
status);
rate = zd_rx_rate(buffer, status);

2
include/net/mac80211.h
View File

@ -547,7 +547,6 @@ enum mac80211_rx_flags {
* unspecified depending on the hardware capabilities flags
* @IEEE80211_HW_SIGNAL_*
* @noise: noise when receiving this frame, in dBm.
* @qual: overall signal quality indication, in percent (0-100).
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates or MCS index if
* HT rates are use (RX_FLAG_HT)
@ -559,7 +558,6 @@ struct ieee80211_rx_status {
int freq;
int signal;
int noise;
int __deprecated qual;
int antenna;
int rate_idx;
int flag;

4
net/mac80211/ibss.c
View File

@ -382,6 +382,7 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
struct sta_info *ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
u8 *bssid,u8 *addr, u32 supp_rates)
{
struct ieee80211_if_ibss *ifibss = &sdata->u.ibss;
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
int band = local->hw.conf.channel->band;
@ -397,6 +398,9 @@ struct sta_info *ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
return NULL;
}
if (ifibss->state == IEEE80211_IBSS_MLME_SEARCH)
return NULL;
if (compare_ether_addr(bssid, sdata->u.ibss.bssid))
return NULL;

4
net/mac80211/tx.c
View File

@ -1419,6 +1419,10 @@ static bool need_dynamic_ps(struct ieee80211_local *local)
if (!local->ps_sdata)
return false;
/* No point if we're going to suspend */
if (local->quiescing)
return false;
return true;
}

12
net/mac80211/util.c
View File

@ -1039,7 +1039,19 @@ int ieee80211_reconfig(struct ieee80211_local *local)
/* restart hardware */
if (local->open_count) {
/*
* Upon resume hardware can sometimes be goofy due to
* various platform / driver / bus issues, so restarting
* the device may at times not work immediately. Propagate
* the error.
*/
res = drv_start(local);
if (res) {
WARN(local->suspended, "Harware became unavailable "
"upon resume. This is could be a software issue"
"prior to suspend or a harware issue\n");
return res;
}
ieee80211_led_radio(local, true);
}

13
net/wireless/mlme.c
View File

@ -93,7 +93,18 @@ void cfg80211_send_rx_assoc(struct net_device *dev, const u8 *buf, size_t len)
}
}
WARN_ON(!bss);
/*
* We might be coming here because the driver reported
* a successful association at the same time as the
* user requested a deauth. In that case, we will have
* removed the BSS from the auth_bsses list due to the
* deauth request when the assoc response makes it. If
* the two code paths acquire the lock the other way
* around, that's just the standard situation of a
* deauth being requested while connected.
*/
if (!bss)
goto out;
} else if (wdev->conn) {
cfg80211_sme_failed_assoc(wdev);
/*

13
net/wireless/scan.c
View File

@ -601,7 +601,7 @@ int cfg80211_wext_siwscan(struct net_device *dev,
struct cfg80211_registered_device *rdev;
struct wiphy *wiphy;
struct iw_scan_req *wreq = NULL;
struct cfg80211_scan_request *creq;
struct cfg80211_scan_request *creq = NULL;
int i, err, n_channels = 0;
enum ieee80211_band band;
@ -694,8 +694,10 @@ int cfg80211_wext_siwscan(struct net_device *dev,
/* translate "Scan for SSID" request */
if (wreq) {
if (wrqu->data.flags & IW_SCAN_THIS_ESSID) {
if (wreq->essid_len > IEEE80211_MAX_SSID_LEN)
return -EINVAL;
if (wreq->essid_len > IEEE80211_MAX_SSID_LEN) {
err = -EINVAL;
goto out;
}
memcpy(creq->ssids[0].ssid, wreq->essid, wreq->essid_len);
creq->ssids[0].ssid_len = wreq->essid_len;
}
@ -707,12 +709,15 @@ int cfg80211_wext_siwscan(struct net_device *dev,
err = rdev->ops->scan(wiphy, dev, creq);
if (err) {
rdev->scan_req = NULL;
kfree(creq);
/* creq will be freed below */
} else {
nl80211_send_scan_start(rdev, dev);
/* creq now owned by driver */
creq = NULL;
dev_hold(dev);
}
out:
kfree(creq);
cfg80211_unlock_rdev(rdev);
return err;
}